Search results

I have a Kubota B4200 (1995) compact tractor, that I have turf tires and need to know the tire pressure to use on the front, 20X8X10 on the rear 29X12X15? thanks John

JD X580 using a lot of gas when mowing I have 2022 JD X580 with 18 hours on it. I am using a lot of gas when mowing at full throttle. The dealer said to put the rpm just in the green on the tack and if the mower runs good then cut there. I did this and the mower ran good did not use as much...

KeystoneKid2121 Reference your March 18, 2023, you asked when to do the first fluid change, I added two charts that were in text format and did not make any since. Since then, I changed them to PDF format and the came out good, so they are attached, and you can use them or make changes to suit...

I have a B4200 Kubota 2 cyl. diesel that is not getting fuel to start. I replaced the fuel filter and filled the fuel bowl with diesel fuel then turned the fuel shut off back on. Tractor started no problem and drove about 50 ft. and shut down. Would turn over but not start so I loosened the...

A very special thanks to WILL 1988 who suggested I buy a JD X580 and to javjacob and Bertmobile for their comments back on 11-11-22. I bought the JDX580 with a 47" snow blower in December, and this is the first time I have used it for snow and what a great machine even though the snow was about...

I have a Agco Allis 918H garden tractor that I want to sell how much do you think I can get for it. all in fair condition Agco Allis 918H SN #? 1681with a CH18 Kohler engine SN#2408207227 rebuilt 122.5 hours ago, 48” mower deck, 36” tiller, 42” snow blower with manual or electric controlled...

Hi guys I need some help in deciding what size JD I will need. In the next few months I intend to purchase a new JD. I have an acer of grass that is flat/slight slope with many cobbled stone curbing for flower beds. I pick up at least 200 bushels or more of mulched leaves every fall. I also have...

Hi guys it is John again with the Agco Allis bevel gear box. I just installed a used BGB from the 70” s, shafts were nice and tight installed new seals but when I went to put the PTO the pivot spring loaded pulley assembly and the retaining ring (#2172206sm) it keeps popping out of the grove on...

I received these replies to my post on Agco Allis Bevel Gear Box and can't make them out they appear to be in a foreign language or just SPAM from EarleSew ШґШ±ЩЉШ·-Ш§Щ„Ш¬Щ†Ші-ШіЩЉШ§Ш±Ш©-Щ…ШЩ„ЩЉШ©-Ш§Щ„ШµЩ†Ш№ from Pornstact said: таджик порно домашнее now this post from Pornstack cannot be found...

Hi guys need your help see my post under Simplicity and Allis Chalmers on Agco Allis 918H bevel gear box Does anyone have instruction on how to remove the bevel gear box? I have almost all the bolts out and still it won’t drop down. Does the bolt #157273 stud for the handle to tighten the belt...

Hi guys need your help see my post below on Agco Allis 918H bevel gear box Does anyone have instruction on how to remove the bevel gear box? I have almost all the bolts out and still it won’t drop down. Does the bolt #157273 stud for the handle to tighten the belt from the rear have to come...

Hi guys need your help see my post below on Agco Allis 918H bevel gear box Does anyone have instruction on how to remove the bevel gear box? I have almost all the bolts out and still it won’t drop down. Does the bolt #157273 stud for the handle to tighten the belt from the rear have to come...

Hi guys its John again with the bevel gear box (see topics under Allis Chalmers) Well again the bevel gear box let go. I called the dealer he can do nothing for me on the price of parts but will help out with the labor. This makes the 4th time, once I rebuilt the power take-off and twice, he...

Hi guys its John again with the bevel gear box (see topics below) Well again the bevel gear box let go. I called the dealer he can do nothing for me on the price of parts but will help out with the labor. This makes the 4th time, once I rebuilt the power take-off and twice, he rebuilt the PTO...

I have an Agco Allis 918H that I had the dealer repair the PTO at a cost of around $600 and it worked good thru the winter with the snow blower on now I have the mower on and having a problem with it slipping real bad, so bad the clutch go so hot it burned my hand. It is at the dealers again...

I have an Agco Allis 918H that I had the dealer repair the PTO at a cost of around $600 and it worked good thru the winter with the snow blower on now I have the mower on and having a problem with it slipping real bad, so bad the clutch go so hot it burned my hand. It is at the dealers again...

Guys I guess I explained this wrong it is called in the parts manual "Bevel Gear & Side Plate group" it is for the POWER TAKE OFF not the transmission as I stated And it says” fill with multi-purpose oil until oil touches the bottom” What I posted I have an Agco Allis 918 H and want to add a...

Guys I guess I explained this wrong it is called in the parts manual "Bevel Gear & Side Plate group" it is for the POWER TAKE OFF not the transmission as I stated And it says” fill with multi-purpose oil until oil touches the bottom” What I posted I have an Agco Allis 918 H and want to add a...

I have an Agco Allis 918 H and want to add a little oil to the transmission and it states that to use a multi-purpose oil What is a multi purpose oil, the internet says it is 3 in 1 oil but I think that is to light what oil should I use in the transmission? Thanks John

I have an Agco Allis 918 H and want to add a little oil to the transmission and it states that to use a multi-purpose oil What is a multi purpose oil, the internet says it is 3 in 1 oil but I think that is to light what oil should I use in the transmission? Thanks John

Hi guys need your help again Do you have the valve clearances for a Briggs and Stratton JD High performance technology G 4 crankshaft, Model 441677--Type 0130 E1 Code 061003YG this is in a JD LA120 riding mower I looked all over and finding to many different specs Thanks John

Hi guys hope everyone stayed safe I have a JD-LA-120 ( Home depot ) that is about 9 years old and has 200 hours on it (second machine) this won't move forward or reverse but starts and runs good. It moved when I parked it I removed the mower deck cover to grease the spindles only and did...

I have a Agco Allis 918H (symplicity) that I rebuilt the engine 2 years ago and replaced the stator, I also purchased a cheap rectifier on line and not charging, now I purchased a Kohler rectifier and it is still not charging. I have checked the stator and it is putting out 26 AC volts each...

Hi Guys need some help I have a 1995 Kubota B4200 4 wheel drive with a 2 cylinder 12 HP diesel engine with 812 hours. It has been loosing power Put a new fuel filter and no water in the fuel. Added diesel additive and let run for a while and no change Got any ideas Thank John O

Hi Guys need your help I have a Agco Allis 918 H the PTO get very very hot when running. I t got to the point that it deformed the belt at the PTO. I rebuilt the PTO several years ago. Last winter I put a 42" snow blower and had to make all kids of adjustment. This year I rebuilt the moter...

Hi guys first time at this site, used the B&S forum and it was helpful I have an Acgo Allis garden tractor with Kohler CH18 s and the carb has been replaced with a keihin 24-053-35. I believe it is running lean It back fires threw the exhaust only under heavy load, other than that it runs...

Hi new to this forum I have a 5 HP B&S engine model # 133432 type 00036 08, code 94081807 I have no spark, I replaced the coil with a B&S new armature magneto#397358 purchased for Jacks small engine. I also replace the key and cleaned the flywheel Still no spark I connected the coil wire...