Search results

Hi All, Vtwin will not shut down, if I ground out each coil it will shut down, replaced diode string, soldered connections to coils as they seemed a bit loose, still no Joy, diodes test OK with Fluke meter diode setting. Any thoughts? Thanks Geo🇺🇸

Hi All, looking for pics and doc’s for setting up fixed throttle on a 16 HP B&S V Twin, something different than what is in the B&S manuals. Thanks

Hi All, is there a correct way to install and adjust the throttle cable , the way I have it now it’s hard to operate and seems like it may be fighting the governor, cable moves freely when disconnected. Thanks

Hi, what should the resistance be on a 20 Amp Stator? Thanks

Hi All, can anyone tell me the correct R&R for this stator, it’s a 20 Amp.

Hi All, what could be causing a really erratic idle on an M8 , governor rod is jumping all of the place. Thanks

Hi All. Trying to get the fuel pump working on this 16HP vacuum pulse pump, should we be able to read vacuum pressure from the valve cover port ? if so, how much. 2nd pump and have the same results, no fuel to carb.

Hi All, having great difficulty installing and aftermarket recoil starter assembly, original was taken apart by my son and who knows where 1/2 the parts are, anyway the white plastic pawl with the little pin keeps snapping off, this is my second try, I wonder if a factory pawl would be a better...

Hi All, I pulled the fuel supply line off this carb, and found this substance in the port, it can’t possible be normal, engine did run quite will, I removed the top of the carb and everything looked ok , this substance blew out with compressed air, lower port is connection for PVC tube. Any...

Hi All, primer bulb not priming, new tubing, has been working fine until it stopped and there is no fuel in the bulb after pumping many times. Geo??

Hi All, before I tear this fuel pump apart, any idea what’s causing it to weep out of the two holes on the top? engine runs fine otherwise. It’s a Mikuni pump. Geo ??

Hi All , B&S Vangard 16 HP , switch has R B S A I. What I used R from rectifier, B battery , S start, and A for accessories, not sure what the I terminal would be for, motor has a magneto ignition, does this switch short out internally to kill the motor? I haven’t started it yet , only...

Hi All, what is the tap size for the emulsion tube on a B&S Flo Jet carb. Thanks Geo??

Hi All, looking to possibly replacing a Kohler M8S motor, hopefully something that would plug and play as much as possible. Thanks

Hi All ! B&S Flo Jet 2 piece, leaks out of the hole past the chock plate, is that because the float is set wrong? seems these carbs are a real problem, although the one on my 6R6 seems to be working fine. Geo??

Hi All, B&S. Vangard , battery drains over night, 2.29 Amps of parasitic voltage, after much TS. I removed the positive lead to the alternator which cleared up that load, alternator is putting out 13.5 VDC , replaced the Regulator/Rectifier with one from another engine, same results, I should...

Hi All, installed this carb on my 6R6 B&S , no leaks, I set it according to specs for starting, it will fire and runs for a short bit, how should the throttle be set when I am trying to start it? and what else s I try? Thanks Geo??

Hi All, back again, anyone have good pictures as to how the carb. linkage should be set up on this engine, I need something other than what is in the B&S manual , I don’t have a rod for linkage adjustment, see pics.

Hi All, this engine is on a pressure washer, originally ran out of oil, refilled with clean oil, ran fine for quite awhile until it stopped again, drained oil which was grey in color, when I tried to restart it just seemed to spin freely, I disassembled it, piston and rings seem fine at least...

Hi All, looking for a video for rebuilding a B&S carb, #99876, I believe that the venture in this carb is placed in the wrong position but I would like to confirm, is this tiny hole supposed to be clear? Can’t poke a paper clip through it. Thanks Geo??

Hi All, there are 2 wires on this magneto, 1 goes to ground terminated right on the mag mounting screw, where does the other wire connect? 1 obliviously there is the plug wire there also. Geo??

DELETE

Hi All, I have a B&S 10T802 0547 B2 engine, on a push mower, it has no power, fresh gas, new plug, clean air filter, under deck clean, seems like the governor is not working correctly, it has been adjusted per specs , no springs involved just a straight rod from carb to governor shaft. almost...