Search results

I found it at a dump site. No bar/Chain and trigger lock is missing. So where is the S.N. located? I found no tags other than EPA and Saw shop decal. Would like to know what year of manufacture. I have no way for a photo/ What size bar/chain 45 CC Air Induction Thanks

Why does the pto for the blades wind up faster when the deck is higher ? Belt and pto linkage are ok. The deck height system seems to me to be the culprit. Rather than lift system lifting the deck straight up keeping belt tension equal regardless of position. When raising it moves the deck to...

Can spray carb cleaner be used to clean internaly a Zama W-26 Carb????

What would be the base settings be for a old Woodshark 14 inch saw? I live at 2500 feet.

Mower leaks fuel from carburator when shut down. I put a shutoff valve before the filter to temporarily solve problem 3 years ago. I,m guessing that its from that solenoid but its hard for me to see down there. Is that solenoid really necessary? Or should I buy a solenoid and orings? Does a...

Is there a adjustment for chainoil. My echo has a screw to adjust but I haven,t found anything on the Poulan. Is there really a weight for chainoil with temp changes?

I need picture or something on th gov. spring adjustment. Transition from no load to medium load without the rpm lag. Is this common on a single cylinder? What iis the bolt looking adjuster on the gov levrer?What is the purose of the skinny long spring that surrounds the linkage?

I have a Homelite EHRL 4400 approx 30 years old. I,m sure there can,t be 50 hrs run time. Last time used it had trouble transitioning between small load and larger load. Hesitation. I have just bought a B/S kit for carb. I would like to know how to adjust voltage and the govermnor. Is there...

Its a 2010 gen. that I bough new. It ran well for a few years then the surging started. It would smooth out with half choke. Now it will only run when you put gas down the spark plug hole. But stops Is there a fuel pump on this unit. The knob that allows start/stop feels more that a electric...

I need to find a carb kit or a replacement carb. The engine will not run constant. It just oscillates,/hunts/surges. I cant find any identying data on the carb. I have had the gen since new

I just replaced the clutch drum and clutch large washer. Installed new bar and chain. I have done this at least 3 other times. Cleaed saw replaced fuel filter and all fuel lines and primer.. Th saw starts and runs but bogs down like a binding. I noticed after bar chain it won,t roll chain...

Carb P.N. there any real difference between WT-829 A021001330 and A02100331 other than 20$ in price? Thanks Jim

This saw never did respond quickly to throttle opening. It starts easily ,idles well, cuts good, but now its worse than ever getting up to working rpm, without at least 5/6 squezzes of the trigger. I have replaced the fuel,air filter. The plug is tan color (Help)

My deck doesn,t seem to raise very high. The Handle seems to have a lot of no response movement before deck moves/ Deck wheels drag at times at full up position

Deck lever travels excessively before deck rises? Is there a adjustment for this or rigging procedure?

Well I,m still looking for my non engagement of my mower pto. I looked at the deck with the PTO lever engaged. The belt was still LOOSE. I reached in and moved the lever/Idler pulley approximately 2 inches and that tightened the Belt. As I said before the deck levers move freely and lubed, it...

My LTX 1040 Single cyl Kohler That runs extremely has developed a fuel drip at the Carburator. Its hard for me to get down that low but it feels like its coming from a solenoid on the bowl.hould I buy a solenoid or is there a gasket/oring/crush washer in that system.If I close the fuel shut off...

My pto handle is difficult for wife to move to engage but why doesn,t it return all the way back or is not necessary. They disengage fine but still need more travel at the deck lever for a less slip engage. Has anyone added some washers/shims behing the cable ferrul on the deck or maybe a...

Bought a new OEM belt and 2 idlers. Removed all levers and springs, no excessive wear. Dry Lubed and installed deck. Performed much better, but why does the rpm change with deck handle up/down. Why is the deck belt a A sec. . when the pulleys are wide like the other belts on the machine 5/8 wide.

It might start but won,t stay running. Removed tank n cleaned replaced lines and filter. still the same. Replaced fuel primer, seemed like the bulb was loosing its mojo.,. I then removed carb WTA-28 Dissasembled (looked clean but let soaked 24 hours in carb cleaner. Removed from cleaner and...

My LTX 1040 that I bought from neighbor as the second owner. Its 1 cyl with 42 inch deck . I,m having issues with pto engagement especially when I move height lever. I was looking under the tractor and noticed that both arms were factory stamped with the number 38?????? could this be the...

My LTX 1040 that I bought from neighbor as the second owner. Its 1 cyl with 42 inch deck . I,m having issues with pto engagement especially when I move height lever. I was looking under the tractor and noticed that both arms were factory stamped with the number 38?????? could this be the...