Search results

This is what I have found on the valves Do I set them at TDC? Can I do them like I do a Briggs one valve open and one closed? First Kawasaki I have had. Started getting a puff of smoke just on start up. And not every time.

Are the older grey echo trimmers as good as the new ones? to be the best you have to beat the best

6.5 power sport side shaft leaking oil out of governor shaft. Is there a O ring there?

Just some mowers

How much would you sell it for?

I as you all know I am not a JD fan But in my search for a deck belt for my toro. $110 at the dealer $42 on eBay. I found that a JD belt number gx20305 is 1/32 wider and 7/8 longer and sits in the pulleys very nice. Works better then the toro belt. No belt squealing when I engage the pto...

Has anyone used two V belts on the wheel drive pulleys rather then the $80 drive belt. The stock belt is 1 1/8 inch wide by 52 1/4 long I am thinking two V belts will work.

Ok I have a snapper pro walk behind. Around a 1998. No model numbers. Trying to find the two drive belts for the wheels. It is the wide belt with a groove in the middle. Same as a ferris so I have part numbers but can not find a belt. 1521442. New number is 1521447. Has anyone just used...

Have a peerless/Tecumseh transmission model number. 4988-p1. Replaced both shafts and all gears but the little beveled gear that sits on the pulley shaft Reverse 1st and 2nd work ok but a little slow to engage. 3rd and 4th will turn the output shaft until I release the brake and try to move...

Have a kohler cv14t 1497 Need number for a carb kit. It is on a snapper walk behind. Maybe from 1998

A friend sent this to me asking if it is worth it. I think it is what do you all think. http://chattanooga.craigslist.org/grd/4366875025.html

Have 2 ryobi trimmers that the coil went bad on this year. I made a comment about them on the ryobi Facebook page. They sent me a email asking about it I told them how much I use the trimmer. He told me even tho it is not considered a commercial unit it should still last. And is sending me...

I have always wanted to know why they use sealed bearing in blade spindles and not a two piece roller bearing. So here is my test. Putting bearing and a race in a mtd housing with a ayp shaft ( yes I use mtd housing on my ayp decks because they are better ) First test was to press the race...

Junk Deere propane kits http://m.deere.com/wps/dcom/en_US/corporate/our_company/news_and_media/news_and_media.page

Just picked up all three for $150 all 3 run and cut. All tires are like new worth the money just for the tires.

Today was my lucky day found this In a back yard of one of my HUD homes. Only thing missing is the chute. (( cowboy up and get over it ))

Found this for sale $6000 Going to look at it. No will not buy it. (( cowboy up and get over it ))

Can't pass this up for $80 (( cowboy up and get over it ))

Went to 5 repair shops 3 was dealers and none of them can even get me a spindle bearing. Said you can not get just the bearing. Ok so then why can I get it from mtd parts.com Went to NAPA and got all 4. Makes me so mad when I go to a mower shop and all they know is what a book tells them...

What are things you look for when looking to hire help? My biggest thing is if your standing there waiting for me with your hands in your pockets. Just say bye bye. No work boots no job. If you smoke ( I do ) no butts in the yard. Must be able to use a trimmer and leave the bark on the...

Why do so many people cut there grass this short? I will guess about 75% of the yards I cut next door to cut there grass right down to the dirt. This guy has nice weed free grass ( the one on the left ) I cut the HUD home on the right ( all weeds ) and looks better. (( racing is the only...

1990 ayp 12hp 38 deck runs and cuts like new Body and paint is very good Price FREE (( racing is the only sport that you need two balls ))

Can your Honda out cut this. It runs and cuts. He would not sell it so on my way home to build my own. Perfect for tall weeds (( racing is the only sport that you need two balls ))

12hp predator engine, 3 speed hi- low transaxle, yes the wheelie bars are functional, (( racing is the only sport that you need two balls ))

My wife wanted a riding mower so got this for her today. Have not tried it out yet but it has very good reviews for its class mower. She gets to try it out tomorrow on some nice thick 8 inch tall fescue. (( racing is the only sport that you need two balls ))

HUD home today work order was to remove pine straw and pinecones We got out the blowers and made beds around the trees Sent from my iPhone using LMF

http://youtu.be/cLxq5GeQWMY This is the only JD I have. This is me and my son taking down the sand washing tank Sent from my iPhone using LMF

Have asked this a few times and still can not find out why. 5hp Briggs will not start getting gas pull the plug and ground it next to the plug hole and it runs put plug back in and it will not run. 20hp briggs twin same thing just pulling one plug and ground next to the plug hole. Many have...

Can any one tell when this was made? And how you can tell this ? Sent from my iPhone using LMF

Been selling this for a month best offer is $150 This thing runs and cuts like new What do you all think Sent from my iPhone using LMF

Got this for free today been sitting in a barn for I know 5 years Got it home did new oil. Took bowl off of carb cleaned and put back on put gas and a battery air on the tires Fired right up and cut my half acre back yard. Now I get to take it all a part and rebuild it. Sent from my iPhone...

What type of grass do you like the most and why?? Sent from my iPhone using LMF

Clutch disk does not last long maybe 20 hours. Got this mower had been sitting a few years had some chunks missing so replaced with a new one and same thing. About 3 hours of mowing it had 2 chunks in it and getting more every time I use it. I have looked and looked and it does not hit...

Anyone ever use one? Guy wants $200 for it it's a 2002 with a 16hp Briggs that he can not get to run I am sure it will run and know I can make money off it. But have never used one and wanting to know how good they are Sent from my iPhone using LMF

Friend has a rear engine said will only drive in 5th and reverse. I am sure there is a adjustment for this ? Thank you for your help Sent from my iPhone using LMF

Ok I have a customer that has a large bed about 1/2 acre of English ivy that has over the past year has got alot of poison ivy growing. Does any one know or heard of away to kill the poison ivy and not the English ivy? Sent from my iPhone using LMF

Not a snapper fan but could not pass this up just drove two hours to get a 1642 could not find anything wrong with the mower it self. The man was selling it because it has gas in the oil someone cut the post off the fuel selanoid I td the man flush the engine out put new oil and a cut off...

Made parts list to start my build on this yard man garden tractor hi/lo 14 speed. It looks kinda bad right now but really it's not as bad as it looks Ordered a lot of new parts going to pass on a new hood and go with a bolens I have in the shop. I hope this turns out to be as much fun as I...

I do mine on a bench grinder free hand. I do know a man that made a jig but I would think is only good for the blades he uses Sent from my iPhone using LMF

Never used one but for $35 and runs like new. If I don't like it I am sure can double my money Sent from my iPhone using LMF

Has anyone used one of these and do you think this is a ok deal???? ZERO TURN CUB CADET LAWNMOWER .50 INCH. 22 H.P. HAS STEERING WHEEL. 40 HOURS LIKE NEW $2500.00 Looks just like one with the two handles but has a steering wheel not sure how you could make a Y turn Sent from my iPhone using LMF

20 hp Briggs was running bad put sea foam in ran like new still runs like new but when I shut it off and drive to next yard it won't start I put new coil on still the same I pulled a plug grounded it out next to the plug hole and it runs put plug back in and won't run. Plugs are new got...

Will it hurt anything if you run a 20hp twin Briggs with out a muffler?

Blade belt calls for a 92.25 I ran a 91 could this be why the belt broke after one yard of tall thick grass

Hi. I have a 1998 20 hp Briggs ran fine I hit a tree it started to pop out of the carb I rebuilt carb ran fine for a few hours now wants to stall when blades are on pulled Plugs they both had black dry carbon on them. Oh and before carb rebuild would only run on full choke. Thank you for any help

Hi. I have a 1998 20 hp Briggs ran fine I hit a tree it started to pop out of the carb I rebuilt carb ran fine for a few hours now wants to stall when blades are on pulled Plugs they both had black dry carbon on them. Oh and before carb rebuild would only run on full choke. Thank you for any help