engine

I have at last found a mower that seems to suit my requirements. Al-ko 520. Key start. Side chute. But it has a choice of engines. Honda, B&S, Longcin. What is best? Thanks.

I have a Kohler engine KT725-3031 that I can't get to run. I've replaced the fuel pump and carburetor and it will only run with carburetor cleaner for just a second. Fuel is getting to the carburetor, at least to fuel filter. It has a thermostat assembly 32 755 27-s that attaches to the side...

Battery was dead when I went to start engine about 2 hours after shutting down following 2 hours of mowing. Suspect battery is junk (it is at least 3 years old). BUT…when I charged it overnight, it came up to 12.5V and started engine, and here’s the thing, when I measured V at battery while...

Lost fire and need specs to check out the coil? Cant find them in a manual or on the internet?

I have a mower with the above engine in it 2018 vintage, my problem is I can find numerous stamps and stickers on the engine but nothing that seems to relate to the model etc numbers. stamped on the exhaust is 595506. And on a sticker on the flywheel cover 17 0908 56 8126. my problem is when I...

The engine on my Toro Super Recycler is using oil. I don't think it will last much longer. The rest of the mower is in excellent shape. B&S made some major changes to the replacement engine. The carburetor and muffler are now on opposite sides ! How hard is it to attach the throttle and...

Engine has been maintained but recently locked up. Any suggestions?

The engine just stopped, it will not crank!! nothing no clicking nothing, I did not hit anything. had to push it to the shed now what. It has fuel I checked the volts the other day when it was running had 13V. Is there a cut out for the oil level?? I thought I checked it before starting and it...

Just curious if a Kawasaki engine out of a JD 175 which is a 14hp will fit/work in a JD 240. These two lawn tractors are about the same age relative to years produced. I know the 240 had a pressurized oil lubrication system and oil filter but not sure if the 175 has the oil filter. Looks like...

Building a log splitter with an Intek 25 horse engine and need to know how to wire it. The original l engine was a a 13 horse but was worn out. I bought the 44t977 but didn’t realize it needed a battery connection for it to run my old set up I just used a jump pack to start it and choked it to...

So I was able to find a TB110 diagram on jack's site, but it doesn't include the engine. Here is my engine label, it has lots of odd numbers on them but I can't seem to successfully search any of them to get an engine diagram. Did I miss a different label or is something else going on here? I'm...

I have a Briggs and Stratton engine on a log splitter that needs to be replaced. I got it for free but the engine is locked up due to the old owner running it without oil. Its on a Huskee 22 ton log splitter. Honestly it looks like a push mower engine but I wasn't sure if one would work. I did...

I'm trying to fix a friends rider. It has a B&S 22 hp v-twin 'professional' series engine, model 44U677-0002 G1. It has a single barrel carb. The problem: When he's mowing, the engine will run fine, but then fade out, spit thru the carb once or twice, then come back and be fine for a little...

Engine was running fairly good but started surging so I replaced the carburetor and crankcase air breather tube and now the engine produces a lot of smoke and will not stay running. Any ideas?

I have an Kawasaki® FR691V Twin 23 hp/726cc. It is on an ariens ikon xd 52. I want to replace it with a FS691V. Will this work as a replacement? The FS engine is slightly large. That is about all I know.

have a cub cadetsc500 21 inch electric start mower with the following engine 2P70MU have cleaned carb it will start and run for a few seconds acting like not getting gas, so put a new carb on it and it does the same thiing, will not stay runnung like it is not getting gas any help would very...

I had problems starting my JD zero turn with B&S Vtech. Would start only if I put drops of fuel on air filter. This got worse until I finally changed carb with OEM. Ran great for a couple days then would die while running as if out of gas. I had put on a manual gas shutoff while swapping carb...

Bowens 11A-584E765 mower. B&S 3BSXS.1581VG engine. You fire the engine up and after 10-30 seconds it starts a sporadic miss in the RPMs. The spark plug is on the sooty side of black.

I hope this is the place to ask this question. It's a bit open ended. While mowing his lawn, my father in law heard a clunk and noticed that what appeared to oil was coming from the bottom/back of his mower. It's a Husqvarna MZT-61 with a 27hp Briggs engine. My question is two part. 1. With...

Hello, was mowing with JD 777 zero turn. Engine just stopped after mowing about 30 minutes. Cranks and has fire, but will not start.

This topic came up after I started a thread about my starter on this engine. Seemed like a new thread is in order: One or more significant oil leaks have existed for sometime causing quite a mess on the entire upper engine (mostly hidden by the engine cover). Txmowman pointed to the breather...

i have a hustler raptor mower with a kohler 7000 series engine..it has started to sputter like its running out of gas..i am going to change the fuel filter to see if that helps..what else should i check?

In the last two weeks I've done many things, but in the meantime the current problem is this definitely getting spark to the spark plug after spraying carburetor cleaner into the intake while turning the key. The only thing that happens is backfire through the carburetor or popping the engine...

I picked up a toro recycler 22 with Briggs 128m02-3425-b1 engine. Compression was very weak, I lapped the valve seats and it started up and ran great. I did a 10 minute or so test cut, changed the drive belt and cut my front yard. Ran great. I changed the oil, and it hasn't started since...

Anybody know what the valve clearances are supposed to be on a Briggs & Stratton Model# 08P502-0169F

I retired about 3 years ago after 48 years as a Ford/Lincoln Mercury tech. Now I spend my time fixing other things. I have a neighbor with a 1999 Exmark Lazer Z, model LZ22LKA604 and serial #204513 and engine #FD661D003939. It is a Kawasaki V twin, water cooled. Over the years I have...

I have a GX200 6.5 Hp powered pressure washer that is too difficult to pull-start. I took it on as a project, but things are not looking good. I've checked the valve lash (to make sure the anti-compression was opening the valve a bit) and the crank key (to make sure kickback wasn't from...

I have a 19hp Briggs and Stratton engine on a Husqvarna 2042 YTH. I have changed the plug, cleaned fuel tank, cleaned carburetor, and checked the seat switch. The issue is that after about an hour of mower the engine will stutter/bog down. I can release the blade switch the engine will...

I put a new battery into the mower and it worked fine. But the red plastic cover over the positive terminal was shot - so I ordered some covers. Today I installed them on both terminals - r/b. The starter gets juice but it doesn't turn over. Sounds like a stuck solenoid on a 1966 Ford I used...

I recently bought a cheap used Bolens 11A-020W765 mower with the 125cc Briggs 08P502-0165 engine, which has the plastic carb and foam air filter. I got it for trim work, but before I needed to use it for that, I needed to use it to mow a small yard. The first time I tried to mow with it, it ran...

I'm looking for a muffler for my ZTH6127 mower.

I think I posted something about this a couple weeks ago. On startup after sitting idle for a season this John Deere D140 riding mower with a B&S 24hp motor revved up so high I thought it was going to blow up. The governor went full throttle and would not go to an idle. I took the engine apart...

The engine I was working on is a Kohler Command CV22S. It is a 2001 and running great. I had just changed the oil and was test running the engine. During the checking of the oil level I noticed that it was a little foamy. That should have set off an alert. I continued noting that the oil...

The engine started surging after running and cutting for about 10 minutes. RPMs up and down and then had to engage choke to keep it running but RPMs would still hunt and then it would die. I installed: New carburetor New air filter New fuel lines New fuel pump New fuel filter New gas Removed and...

M# LGT2654 Product # 960450047 S# 061815A031116 Briggs 407777 0274 G5 A couple of issues here. This engine has the smaller crank because it had the manual PTO. The rider it's on now, once had an electric PTO. Using the crank & deck pulley, the deck belt pulley rubs the drag links when I turn...

I got an areins lawn mower for free and the previous person ripped all of the wiring out and I have to start from scratch. I dont plan on redoing all the wiring like it was originally, I just want the seat. Is there a way to wire it up a kill switch where if I get out of the seat it would not...

I have posted the problems that I have with my BADBOY 2009 Lightning not stating. Here is a new thread that I am hoping will get me some new help. It starts and runs until the engine warms up gets hot them dies and will not restart until it cools down or about a 30 mins to a hour. I have...

please delete

2 of the 3 bolts that attach the engine to the mower deck ripped out of the mower deck of my self propelled push mower. What is the fix for this? I don't have access to a welder.

I have a Toro 3072 mower with what I believe is a Toro engine model lc1p65fc engine. Presently it will start first pull and run perfectly. It will not restart when warm. It will sometimes stutter, cough and maybe start and run ok. I've run out of things to check. Is the attached photo of the...

I have a bolens bl41can 0 tiller with a bad engine. I have a Stihl f38 trimmer and an echo trimmer with good engines. Can I use the trimmer engines on the tiller?

I built this log splitter about 25 years ago and it has split may tons of wood during that time. I changed the oil about a month ago and a few days ago I started it and it had a knock. I've started it several times and it knocks every time. The engine numbers are 252417 5526 01 and I assume this...

I bought a 44S977-0032-G1 engine to replace my failed engine. Does anyone know what the wires are for this engine? There are 3 colored wires Red goes to the voltage rectifier and regulator, There is a grey wire which I am assuming is the fuel cut off solenoid. And there is a Black wire which I...

G'day all Got a TS 142T husqvarna fitted with a Loncin CC HV764 engine Displays typical no ACR symptoms so after wasting a day trying to find the specs for the engine , I thought i might just have a stab After fighting with the glued on rocker covers for an hour I find every rocker has a...

Hi all. I need to remove the engine from my Hayter Hobby 41 mower. The engine is a Briggs and Stratton unit: Model: 94502 Type: 5911-02 Code: 88072804 The flywheel (underneath, where the blade mounts) needs to be removed from the crank to get the engine out. I suspect it is a push fit with...

Hi all. I need to remove the engine from my Hayter Hobby 41 mower. The engine is a Briggs and Stratton unit: Model: 94502 Type: 5911-02 Code: 88072804 The frictiod disc (underneath, where the blade mounts) needs to be removed from the crank to get the engine out. I suspect it is a push fit with...

I have a new (4.2 hours) 19 day old 2024 Ferris ISX2200 w/28hp Vanguard engine. When delivered I asked the delivery guy if everything had been checked and he stated that it was "ready to mow". After mowing for two hours, the mower was parked in the shop. Next day I decided to check the oil...

My Honda HRN 21 inch mower had some debris & caked up oil on the block of the engine and I was wondering if it’s safe to spray on a degreaser ( heat the engine first?) on the engine and then spray the entire engine with water from a pump sprayed.Is this the best way to clean the mower?

I looked at a John Deere 425 this morning. It has the FD620D engine. The serial number tag is gone from the mower so I can't date the mower. I'm reluctant to buy it until I'm sure the engine has steel cams, which I believe are post-1998. The mower has 1435 hours on it. I didn't know where...

I just picked up a fairly nice looking 3311X6S (I am guessing on the 6 - can't remember for sure). I was little surprised to see it was a 1980's model - by the looks I had assumed 1970s or earlier. The previous owner told me about all the trouble had trying to get it to run and how it had sat...