Search results

90 in. worked great.........thanks for the reply.....

I need a drive belt for an old toro...... jack"s recommends 5/8 x 901/2...tracter supply has 5/8 x 90........can i go short a half in????......or can someone recommend another seller........Jack is OUT OF STOCK.......and I have not bought from anywhere else....... thanks for any ideas......

sheared input shaft woodruff key....not flywheel key,,,,,

Ok thanks a lot........the old drive belt was stretched out so that it was rubbing on itself at the tension pulley........the new belt could have put alot more torque to the tranny that was too much for the old key that was about to give up.......??............I'll get it back together when i...

title explains it.......Is this a common problem??..........I replaced the long drive belt [I could have had some slippage with the old belt] I wonder if that kept the pin from shearing??..........I ran the new belt and the deck for ten minutes on the lawn and the wooddruff key gave up....I...

thanks for the reply...looking at the parts blownup is a good thing......but it leaves a lot to the imagination...I think I have all the parts and I am close to figuring it out........i aslo found a manual on an ariens website......I'll go at it again in the morning....

I bought an ariends mower 935009..........003026.......38" deck........I guess they were made from 79 to 89??.....this machine is in very nice condition for its age the deck still has paint showing on the UNDER side....... I got the briggs running right away and changed the oil and cleaned the...

I tore this one down to the circuit board.......no battery.in it.....I got 12 v to two wires but I couldn't get a flicker anywhere......I think it's dead....It had a nice long life........ thanks for your time,,,

I noticed that the hour meter was not working, so i thought I'de start by checking the plugin........i got a 12v reading on one wire and concluded that if i had power to it, that i should get some kind of reading ......the screen is just blank........Is it wiring or just a dead gage??......I'm...

I hope that you checked the oil carefully before you ran it......if that carburetor solenoid was stuck in the down position .......you could have oil and gas mixed........if you have ran it a while chances are that it is ok.........It happened to me, but I was lucky enough that I got so much gas...

I agree, but the manufacture also encloses the engine........I have just a skeleton tube frame on the sides and front I have only the hood hinged on the top of the engine cover......soooo when i get it running I will check the heat, with and without the tin.......I'll post the results, when I...

The fly wheel will be covered with the briggs hood. I'm talking about the tin side plates.........may I'll do a heat test before I start on the opposite side.....thanks for the comment,,,,,,

Do i need to replace the tin on the sides of this v twin?? I'm installing twin stacks and this tin is a pain to deal with....I have open sides with an open frame built for the hood......I would think the open sides would be enough to keep the heat down???.....but you guys are the experts...

.this morning I had to move it because i needed to do a little welding on a spring bracket on my snow blade.....I ended up starting it three or four times before I parked it again........I checked votage at the battery before I shut it down and the regulator wa putting out 14 volts.......so i...

I haven't been under the fly wheel yet, I'll give it a look and a cleanup.......I think this machine spent some time in a colorado town that is used to at least a couple feet of snow all winter, probably uncovered.........thanks a lot for all the info.........

thanks a lot rivets, i'll check it out.........the battery is keeping up ok so far without running the pto, but if I decide I want to mow with it again I don't want the clutch pulling the power out of the battery.......

I have a 22 hp v twin briggs 4o7777, it has a electric pt , Ive checked the out put on the stator and I can't get any more than 24 volts out of it and only 12.5 out of the regulator...........the battery is holding at about 12.5 to 12.7 enough to keep it starting ......I have used the deck only...

I'm a new guy here, but I guess I can chime in too I would check to see if you have a ground wire from the frame to the motor,,,,I had this happen on one of my briggs motors.......

must be 14V809H063.........thanks a lot..... i was getting close :-0

I could not find the number that i thought the tag said, the tag was a little hard to read after all these years.........I figured that the model number was 14AY809H063..... thanks for the tip.........I do plan on putting the correct belt in it, I just have to find one.....i'm checking jacks...

TROY BILT14AM909H063

TROY BILT14AM909H063 1IC29H10224

I bought a 22 year old troy bilt bronco 22 hp vtwin b&s with a vari drive I think it's called, I'm waiting for a carb, in the meantime I checked out the drive...... i have Forward low high and reverse but the only way to stop is to throw it out of gear.....the clutch will not slack up on the...

I think it has 791230 attached to it according to the list..........?? I think you take just as much of a chance ordering parts......that's why i just buy a new one, then if they are the same thats good....and if not, maybe i can get one out of two.........I do have a manual choke,,,,,,,

yep daylight made a difference.......damn 0 with a line through it.........I bet I'm not the first to do that... thanks for the info

sorry about that ..I meant that i found the info that scrubcadet gave me ..... the engine is a 427777 type0128e1 code 99 06 21 yg.........and i can't seem to find that 427777........every thing but that one!......I'll keep looking unless one of you guys can educate me on this engine......

Thanks a lot, since my last post I found this info...........

I bought a troy bilt mower just for something to keep me busy...it has a 22 horse v twin briggs...... the only numbers that i see on the hood are 40 V ohv and xbsxs7242vfe:m.............I need a carburetor but i can't find these exact numbers,,......everything else but 40v..........what am i...

slomo said that he has seen this happen a few times....so I guess it is not uncommon.........

I got my blades,........ opened package and the pattern was a star, OH SH!T.........THE star pattern worked great.....the blades might have been a little lighter than my originals, but the mower doesn't care...... thanks for all the advice and pointers......I'm gonna burn the stump that got the...

I used an 8 lb sledge and my anvil to get it straight, but you need heat for the bend in the cutter end, My torch tanks have been out of gas and oxygen for a couple of years, [ I went from steel work to wood turning, a very satisfying hobby ]...... new blades are cheaper than filling my tanks,,,,,

they measure ..21 and 3/16.........these blades were on this mower upside down when i bought it, the cutting edge never hit a blade of grass.........could be, that's why they sold it.......under the dust it was like new.........

I'll probably get in trouble over this but..........I always say cats are a lot like women...if they want something; they figure a good way to get it.......I had to go and check my order......I was happy to find the right hole and length ......I only saw made in usa and bought them....oregon...

many thanks,,,,,,I'll let ya know if I got the right ones........

this is what I can up with.....apparently they have them in stock......I'm pretty sure these are what I need??? https://www.amazon.com/gp/product/B01M97TNBX/ref=ox_sc_act_title_1?smid=A31NIKG2L2Z2RS&psc=1

I'm 74 and still learning!!.......I had NO idea..........sure enough.....21 and 3/16.........these blades were on this mower upside down when i bought it, the cutting edge never hit a blade of grass.........could be, that's why they sold it.......under the dust it was like new......... now that...

the blades that are in it are an exact 20 inches....[ I don't know that these are original blades??] the mower does a very good job mowing with these blades......I'll have to put them back on the deck and make sure that i have clearance for 21 3/16, that is the blade length on the ones in the...

Thanks a lot for your time bertsmobile1.......I'll try that road and see how i do........Jacks small engines was out of stock [If Idid the search right}....I'll try your other places..........I have a kitty cat trying to help me with this....he just decided to la down on the...

star tec said H or double diamond........ the H pattern apparently is not what i have, what I have is the pattern in his first pic.......now I guess I'll search for a double diamond......thanks for looking.....

i have the H pattern on the blades and I have never found a model # on the mower anywhere....the sticker on the seatback was gone years ago from the looks of it........about all i can tell you is that is a lawn chief 14.5 hp ohv briggs..........42 in cut.....I have the blade straitened......I...

I bent a blade on my old lawn chief and thought that it would be an easy replace....but I can't seem to find the compatible blades anywhere....I can find what looks like it might work but none that i have seen seem to match up with the spindle hole shape??.....Will the star hole fit on my...

sorry to have bothered.......I'm gone.....

I wouldn't think that you would need the info on my machine to lead me to an idea to filter a carborater with a 1 9/16 " inlet.............sorry i took your time.......I'll get it figured out

I got the box for the air filter in the deal, and after straightening and messing with it for and hour I finally got it to where the lid would fit right, then i had to thread some round stock for bolts, and after i got it all set up and in place, I see that you have to pull the filter off to...

Worked great. when i finish my box I'll see if I can post at pic or two......thanks for the replies.......

It's probably triple the size of the copper one that was on it and has a lot thicker insulation, I am wanting to keep ALL the wiring out away from the pullies and and belts......including the solenoid.........thanks for the reply.....

I've built a steel tool [and battery] box off of the back end of this old mtd that I am fooling around with ...I plan to use a full size battery and what ever wieght I might need for traction.....{ my next project for it is a blade]...........I' have lenghth of aluminum battery cable that has...

I'm new here. but i have to give you a handshake on a good job, you saw a problem and instead of complaining, tweaked that machine for your personal useage........Ive always experimented in treeking.........and got a lot of fails over the years, but it sure is fun for me...;-)

kill wire goes to mag.....[kill wire on this motor ran around the other side to the throttle linkage, then to the mag]....there are two wires coming out of the stator, red and black....I have it back together and it is running and charging.......thanks..........Happy Thanksgiving,,,,,

black stator wire pulled out of stator........some call them alternaters don't they??.........sorry i confused you.......I think i have it fixed...thanks for the reply