Search results

Thanks for the info. I did replace both hanger bars as the holes had egg shaped. I also replace the right brake spring as it was missing. The replacement belt is two inches longer than what was on the deck, but it is the correct OEM spec'd length. I will watch and make sure the brakes...

Hello All, I have a 2007 MTD\Troy-Bilt that the deck is causing me nightmares. The deck will vibrate heavily when the blades are first turned on or when under heavy load. When the manual PTO is engaged, it vibrates then smooths out. I have replaced blades, belt and spindle shafts. Blades are...

Did some matching of part numbers and found that they both are a 94mm bore. Parts such as head, valves, piston, gaskets all have the same 20-xxx-yy part number where only the yy number is different. Any idea of wither the parts will be compatible or not. I want to use the sv620 20hp head with...

Sounds positive, tanx

Problem is the engine shroud and valve cover is missing from the CC 22hp motor. Unless stamped on the block somewhere, they're gone.

Hi Everyone, will the head assembly from a Kohler SV470-620 22hp fit a SV470-620 19hp? Are the valves and the bore the same. I have a TB Super Bronco 13BX60TG766 that threw a rod and I need the head, carb and starter from it to make a Cub Cadet 13AX11CH056 motor complete. Thanks for the help.

Gentlemen, thank you all for the advice. I rebuilt a car engine back in the 80s and it was vey important to match the rings to the bore. I have not seen anything related to that or different size rings. Pistons come with rings attached. I am probably jumping the gun as I have not opened to...

slomo- my thoughts were the same. Kit come with rings? If so, generic size? Bertsmobile- can counterweights be reused or best to buy new? Thanks guys

Hello Everyone, I obtained a mower with a Kohler SV590 19hp single on it. I'm pretty sure the connecting rod is broke, as the engine spins free and the piston does not move. I can push it in with a dowel. My question is, what are the chances I can install a piston and rod from another SV590...

Thanks Tinkerer. I'll look first to see if I can download a copy so you don't have to be put out.

Thanks StarTech

Thank Bertsmobile. Both are set to .005 both with one one closed at a time and with both closed. I did not know if it affected the compression relief.

Hi Ya'll, I have a Briggs Intek Single 18hp on a Troy-Bilt rider. Very generic. I have watched many videos on doing the valve adjust. One will have you set the lash by setting the engine at a point where one valve is open and the other closed, and another has you going to 1\4" past TDC and...

Thanks everyone...not wanting to rebuild at this time

Bolts are tight...someone has been inside before. lots of red silicone. Thanks

I have a Kohler 19hp Courage single on a mower with a powered pto. I have a Briggs 17hp Intek single that was a manual pto. Can I swap the 10 amp magneto fron the Kohler and put it on the Briggs?

I have a Kohler 19hp Courage single on a mower with a powered pto. I have a Briggs 17hp Intek single that was a manual pto. Can I swap the 10 amp magneto fron the Kohler and put it on the Briggs?

It's got to be EPA vent. Runs great not connected. No place to connect.

Thanks for that, I wondered if that was the case.

Depends on usage. I have a small residential grade 42" and a 60" commercial. For everyday home use, the residential is fine, save the money. I've had mine for 8 years now and it still running great. But I don't baby my machine when I'm cutting my 2 acre lot. That deck will mow down trees...

I have a 60" and a 42" ZT. Yard is divided into large and smaller sections. The 60" cuts a lot of lawn but in the smaller spaces requires a lot of maneuvering. This takes time. I prefer the smaller unit here, but here's a suggestion. Go over a 42". That size deck does not extend beyond the...

Got this garage find and engine was free when parked a year ago. Craftsman DVT4000 lawn tractor. Was seized when I got it. Small amount of Mystery Oil in cylinder over night freed it. Now it turns very hard (breaker bar on shaft bolt). Starter will not rotate it. Plug is out and belts are...

I have disassembled the front steering components, clean, greased and reassembled and this has cured the hard steering. The front tires are very hard and has a smooth thread. I think they just do not grip and then mower slides in stead of turning at very sharp turns. I will live with this.

I'm replacing the plastic carb that is the no choke model. Supplied with the carb is 1\8" id tubing that I'm guessing hooks to the small white barbed fitting on the side of the carb. What is that fitting for and where, if anywhere, does it connect. The primer bulb feeds the front of the carb...

I have about a Toro Sw4200 steering wheel zero turn that's about 5+ years old. It is steadily becoming harder to turn, moving or not. Front wheel spindles and wheels hubs have been disassembled and greased. Tire pressure is correct. Also, the mower will continue to slide straight, sometimes...