Search results

Results 1 to 50 of 500
  1. S

    Hustler New Front Tyres

    Thanks Auto Doc's - Yes and decided against solids & semi solids. My mowers, much like my tractor and skid steer, depend of the flex/give in the pneumatic tyres for a small amount of ride comfort. Solids will take that away and make the ride just that little bit harsher (hard on my antient...
  2. S

    Hustler New Front Tyres

    I am about to replace my Super Z front tyres (13 x 6.50-6). I have found Kenda K404 Smooth (no tread) tyres similar to the origional. Can't say I have had any more than the usual problems with the OM's, but like the "look" of tyres with tread better. Do smooth get more or less punctures...
  3. S

    2008 Hustler Super Z Diesel - To repair or wave the white flag

    I think the low hours and the far too early hydraulic failures, suggest on going issues that you have unfortunately bought into. Repairing equipment is one of my retirement hobbies - if you are not into this sort of perversion, you may have to consider cutting your loses and selling to some old...
  4. S

    Bad fan in 2008 Super Z diesel

    If the fan is anything like the ones I have seen, it will be supplied by one of the auto thermostatic fan makers eg Davis Craig. Be sure to get your fan mounting dimensions and fan rotation direction details to compare with new. :devilish:
  5. S

    Hustler Super Z/60" xr-7 Deck, Idler Pulleys

    Has anyone tried to replace the bearing in one of these Flanged Flat Idler Pulleys ? Just checked one out - has about 6-8 spot welds holding the two halves' of the pulley together. Looks like it may be passible to drill out the spot welds, replace the bearing with good, rivet the two halves...
  6. S

    Hustler Super Z/60" xr-7 Deck, Idler Pulleys

    Hi Rivets, Thanks for getting back to me. Page 7-4 7--5 Part Number 781385, 6" Idler Pulley, x 3, appears to be the right part. I looked up the shaft/bolt PN 783738 x 3, CS .625-11 X 3.00 FULL HX G5 ZN CS: Cap Screw (Hex Bolt) .625: 5/8-inch nominal diameter (0.625 inches) (= 15.88mm...
  7. S

    Hustler Super Z/60" xr-7 Deck, Idler Pulleys

    My Hustler project has four idler pulleys. Three fixed, one tensioner. The two front ones feel loose - would like to replace them. Shaft OD 5/8" Two front are the same 6 3/4" OD, approximately 3/4 height, 21/32" ID (inner bearing). Both black, flat , assume welded. One (Good) at the back...
  8. S

    Mower Noise

    Speculating; Can't be correct. It may be true (in your neck of the woods) that they have to conformed to a Max dB, measured at a certain distance but that certainly doesn't mean that some may not be quieter than others. :devilish:
  9. S

    Tyre Goop & Slow Leaks

    They certainly are not "cheap" - I do know what you mean, which is poor quality. Mower tyres are actually very expensive and at the same time low quality, when you compare what you get to an automotive tyre. I can only assume this is due to lower volume sales. :devilish:
  10. S

    Tyre Goop & Slow Leaks

    Slow leaks are when the tyre loses pressure over many days. Mower tyres seem to be particularly prone to slow leaks. Small volume and lightweight construction, likly causes. I am attracted to the idea of using one of the liquid "goop" repairs, to extend the time between needing to add air to...
  11. S

    Kohler CV 745 FI (27 hp) Muffler

    Thanks Ilengine :devilish:
  12. S

    Kohler CV 745 FI (27 hp) Muffler

    There is a sensor (O2?) in the exhaust manifold. I'ts been damaged , so I would like to replace it - anyone got a PN or ON for this? :devilish:
  13. S

    To Tube or Not to Tube

    "The rims are likely no good to try and mount new tires on anyway and tire shops hate trying to install tubes on these small tires." They don't look the best externally. I will know how good they are when I take the old tires off. Just bought new bearings for them, so hope I havens wasted my...
  14. S

    To Tube or Not to Tube

    Current tubeless tires have had it - need to be replased. Have decided not to go with "flat free"/semi solids. Pneumatic tires give a much better ride (bit of suspension). I have always found that small tires like these, appear to lose pressure much quicker than larger. Makes sense when you...
  15. S

    To Tube or Not to Tube

    I am contemplating replacing the warn out front tires (13 x 6.50 - 6) on my Hustler Super Z . Do you recomend; Tubes or tube less?? 4 ply or 6ply ?? :devilish:
  16. S

    Mower Deck & Grass Baffle Metal

    I am repairing some wear & tear on my Hustler Super Z mower deck grass baffles, which are warn & cracked in places. It occurred to me that repairing with mild steel sheet may not be the best material. My question are; What is the steel used in my mower deck? Something special to resist...
  17. S

    Mower Noise

    Its realy great when the piece & relative quite, of the countryside is shattered by the noise of motorcycles - why would I consider other equipment to be any less intrusive. Even tractors are much quieter (in & out) than when I started in agriculture 50 years ago Most modern engines are...
  18. S

    Mower Noise

    Vanity??? Where on earth did you get that stupid statement from??? Reliability?? - exhaust noise is totally unrelated to the service life of the engine (assuming the nose is not indicative of a problem) - another "left of field comment". Engine/exhaust noise is, for the most part wasted...
  19. S

    Mower Noise

    I didn't know that there are muffler choice options when it comes to mowers ? - please elaborate. May be you are referring to aftermarket options? What's are available ?- again please elaborate :devilish:
  20. S

    Fluid venting through cap in reservoir cap

    "There are no leaks and the machine functions perfectly. " If there is air in the hydraulic oil, it would not perform as the OP stated - got to be something else. :devilish:
  21. S

    Fluid venting through cap in reservoir cap

    "... started noticing oil venting from the tank cap at a pretty good rate" . I ASSUME (??) that this is the transmission hydraulic oil ???? If so the oil is getting hot & expanding. The extra volume of oil is venting, as it must do. The only ways I can think that this could occur is: Wrong...
  22. S

    Mower Noise

    From Google; "...... the Vanguard Big Block (810cc to 993cc) is widely considered the quietest and smoothest running engine in its class. [1, 2] The Evidence: Decibel testing reveals a noticeable difference. For instance, in head-to-head real-world tracking, a Vanguard 40 hp EFI engine...
  23. S

    Mower Noise

    Yes I always use ear protection - Crazy if you don't unless reread profoundly deaf. Still, given the option, I would like to start with quieter mower. :devilish:
  24. S

    Mower Noise

    When considering, zero turn mowers, with the larger petrol engines, 27 hp and up, which tend to be quieter; Kawasaki ? Kohler ? Honda ? Briggs & Stratton (Vanguard) ? :devilish:
  25. S

    Hydraulic System

    I have ordered the new oil filter so should be replacing the oil early next week - How much effort should I put into removing the old oil ie is it necessary/desirable to try & drain the pumps & motors?? OR Is the amount of old oil (unknown type) remaining such a small percentage, that it will...
  26. S

    Hydraulic System

    Thanks Auto Doc/ StarTech, My origination choice (before confusion set in) was a Full Synthetic + Zinc 15W/50 however the Full Synthetic + Zinc 15W/60 (same oil company) is "On Special Sale" for a lot cheaper. Other than cost saving, I also thought that the higher viscosity may be beneficial...
  27. S

    Hydraulic System

    Hi Auto Doc, Dont know if its the Video or something else but it was almost unwatchable due to advertising breaks. That aside - Zinc would certainly seem to have significant wear reduction characteristics. Remembering that this is an old machine with unknown oil in the hydraulic system (some...
  28. S

    Hydraulic System

    Managed to get into "Bob the Oil Guy" website. If anything it posses more questions than answers. :devilish:
  29. S

    Hydraulic System

    Hi Auto Doc, Thanks for the above however you haven't actually commented on straight 20W/50 motor oil V a synthetic 15W/50 with Zinc. I tried to register on the "Bob the Oil Guy" website - ran into problems, so at the moment unable to discuss the options with Bobs members. Also having...
  30. S

    Hydraulic System

    Totally confused; My local Hustler dealer says I should not use an oil with Zinc additive but recommends a synthetic in the hydraulic transmission. (Both of the oils, mentioned above, have Zinc) The various oil manufactures technical advisors say that this older Hydro Gear system and I...
  31. S

    Mr. Funnel Problem

    I have no less than three Mr Funnels - small, medium & large. The first two use a single filter, the last, two filters. Reason for so many is that the small is used on my mowers/stationary engines and the medium /large on my home built aircraft. The small accommodates low fuel flow for small...
  32. S

    Hydraulic System

    Went for the first "drive" this afternoon - transmission works just like new. Will now replace hydraulic filter PN 783936. For the oil I am leaning towards B&S Vanguard Full Synthetic 15W/50 OR Penrite Full Synthetic HPR 15, 15W-60 (best price) Any comments? :devilish:
  33. S

    Kohler CV 745 FI (27 hp) Muffler

    The photo is identical to mine but not my mower. Mine is aesthetically very poor - will look better when I get the project finished. My thanks to Star Tech, the numbers provided will help me get past this problem. :devilish:
  34. S

    Kohler CV 745 FI (27 hp) Muffler

    Sorry ILENGINE if I had that information I would have used it myself. For some strange reason both Hustler & Kohler use stick on Model/Serial Number Labels, rather than punching the details into into metal (like B&S & others do) or using a metal label, riveted to engine/frame (even chainsaws...
  35. S

    Kohler CV 745 FI (27 hp) Muffler

    Hi, Hustlers Super Z, 60" Having trouble finding : Part Number for the Muffler - I am told its a Hustler part, not a Kohler. Alternative to the original part. The original is a vertical muffler with one inlet hole and one exit. Similar (not the same) in appearance to this Kawasaki; I can...
  36. S

    Hustler Barn Find

    Not helpful - Read my last posr. Thank you in advance for whatever information (Model Number of Muffler Part Number) you are able to provide.
  37. S

    Hustler Barn Find

    I don't have the Hustler or Kohler Model or Serial Number of my barn find. The engine may be a Kohler CV 745 (FI) 27-30 hp. The back end of my machine is identical to the above photo. I need to replace the muffler. As far as I understand, it's Hustler part NOT a Kohler BUT because I have no...
  38. S

    "Backyarders" and where to buy used equipment

    I don't know if I fit the characterisation of a "flipper". I have never ever purchased a mower of any description. People give me their "basket cases" just to avoid the disposal effort/cost. I either bring them back to life or keep them for spare parts. I have renovated a few push mowers and...
  39. S

    Hydraulic System

    The hydraulic transmission works!!!! When I say that, its with the wheels off, hubs rotate, at a good speed, in both forward/reverse. Is the above test sufficient to determine the condition of the transmission ie could the hubs work, with no load but be weak when asked to move the mower?? This...
  40. S

    mower hard to turn over after 6 months

    "...when the bale is pulled back." What is the "bale" ?- new term to me. Yet to see an engine fitted with a flywheel brake?
  41. S

    mower hard to turn over after 6 months

    Sounds like something causing friction eg string around the blade shaft, something within the engine cooling cowling rubbing against the fly wheel. :devilish:
  42. S

    Another question about tires

    Just to be pedantic; A wheel is usually made up from several components; Tyre - Outer structure/material in contact with the ground. Rim - Inner frame /structure that supports the Tire & connects with the Hub Hub - Connects the Rim to the axle. Some wheels will have the Rim & Hub in one...
  43. S

    Wide mower with multiple blades not cutting properly

    Wow! I have never seen a cutter disk /head/system quite like that. In theory it should work very well. The more cutters the less each has to do delivering more consistent power demand from the engine and a smoother cut. I wonder if some of the problem may be how the cutter head is set up? My...
  44. S

    Hydraulic System

    True!. That contamination (old/new oil) will exist no matter what I do, short of a complete drain. Should the hydraulics work, I will endeavour to drain as much of the old fluid as possible, before refilling with Hustler Synthetic Oil. Hopefully the percentage of old/new oil will be small and...
  45. S

    Hydraulic System

    Thanks Ilengine - I understand what you are saying about the reservoir level. I have changed all the hoses (not the big return at base of reservoir) and there was no oil in them. This makes me think that the oil in the reservoir may be used up in "filling" the system, resulting in...
  46. S

    Hydraulic System

    I am, trying to resurrect a Hustler Super Z. Taking small steps as I don't want to invest too heavily, before knowing what the outcome will be. I am nearly ready to test the hydraulic transmission. It had been leaking badly, so oil level is well below specified "1in from the top of the...
  47. S

    d140 B&S model 44 popping backfiring thru exhaust

    SGKENT has pretty much covered the majority of possible reasons for backfiring. In my limited experience the most common are: Ignition timing Exhaust valve timing Exhaust valve leaking Small leak in exhaust system has been known to cause backfire when engine decelerated fast. Ignition timing...
  48. S

    Hustler Barn Find

    Well I got the Kohler going this afternoon. Good sign. Had to replace some fuel lines that were leaking fuel out/air in and needed a good big, freshly changed battery to overcome the initial reluctance of not starting for several (?) years. Now that I know its a goer, I have given it a basic...
  49. S

    Uneven Grass Height with JD srx75

    While it is possible to have a level cutter deck, the blade head/spindle angle should always be slightly lower at the front than the back ie you cut with the front arc of the blade not the rear. When adjusting any cutter you measure the blade height, not the deck, from the ground. :devilish:
  50. S

    Air Pressures

    Tyre pressures are usually determined by a combination of load (weight) and carcase deformation ie is the tyre contacting with ground at its max "footprint" Too high pressure reduces ground contact (convex cross section) concentrates wear on the centre of tyre and reduces the suspension...
Back
Top