Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999

sillyboy

Active Member
Joined
Aug 20, 2011
Threads
28
Messages
90
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
Hello All, At the end of last summer I had a mower shop trouble shoot a non-starting engine. It was fixed, but the exhaust smells like it is running rich. Did not smell that way when it was running during the summer (2022).

Does anyone have a diagram (picture), and instructions on how to set up the carb?
I would sent a picture but the mower is still in my shed.

Thank You...
sb
 

smalltimerpm

Active Member
Joined
Feb 4, 2023
Threads
5
Messages
84
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
How long has the fuel been in the gas tank that you are smelling right now?
 

sillyboy

Active Member
Joined
Aug 20, 2011
Threads
28
Messages
90
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
Hi smalltimer, thanks for the reply.
The exhaust odor I smelled (rich), the gas was only 2 weeks older than from when it was running good, with no odor.
I have been storing my mower in the fall, in my shed, since 2009. I put Stabol in the gas every year before storage.
Starts right up in the spring. Battery also removed and kept in my garage on trickle charge.

I just need instructions to set up the carb. ;)

Thanks sb
 

StarTech

Lawn Royalty
Top Poster Of Month
Joined
Feb 19, 2020
Threads
93
Messages
11,589
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
There is only two adjustments that the user can perform.

  • Idle mixture. Set at best speed between too rich and too lean.
  • And idle speed which is usually set at 1750 rpms.
 

smalltimerpm

Active Member
Joined
Feb 4, 2023
Threads
5
Messages
84
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
Maybe make sure correct spark plugs were installed if changed by the shop also.
 

sillyboy

Active Member
Joined
Aug 20, 2011
Threads
28
Messages
90
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
There is only two adjustments that the user can perform.

  • Idle mixture. Set at best speed between too rich and too lean.
  • And idle speed which is usually set at 1750 rpms.
Thank You
 

sillyboy

Active Member
Joined
Aug 20, 2011
Threads
28
Messages
90
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
Hello...On the idle-mixture screw what is the starting point? OR, how many turns out from fully closed? There are lots of conflicting answers to this question online.
Plug was never changed from the shop.

Thanks
 

StarTech

Lawn Royalty
Top Poster Of Month
Joined
Feb 19, 2020
Threads
93
Messages
11,589
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
As a rule of thumb I use 1-1/2 turns from seated position. Note on some carburetors these mixture screws have no effect especially on the idle jetted Nikki carbs; unless, the jet is resized.
 

sillyboy

Active Member
Joined
Aug 20, 2011
Threads
28
Messages
90
  • / Need help with Walbro carb. It's on a "28n700" B&S 15.5 HP. 1999
Thank You so much Star Tech
 
Top