Briggs starter issues grind and locking

The ring gear on this design does not wear the teeth like some designs do.

Basically, you are trying to replace broken parts with worn out parts and it is just not working.

The starter in the picture has everything that moves simply worn out.

Trying to get by using salvage/used parts will send a person in circles like this.

"It can't be the starter.... it was just replaced".

Every time a single cylinder engine stops it will tend to stop in the same spot in relation to the upcoming compression stroke of the cylinder as rotation stops. The more cylinders an engine has, the less likely it is to stop in the same place every time.
 
let's try again. The stater gear is pushed up to engage when it spins. Then it drops back to disengage. Unless you took the photo of the starter with a high speed camera, the starter gear is in the engaged position, and the gear is covered in corrosion. It the starter does not disengage, it will spin and spin with the engine until it kills the flywheel and starter. Being polite, that starter is junk. The shaft or gear is worn out too because there is also too much play in it. It needs to go into the junk metal bin. If you put a good starter on it, it may work. Since the original gear was plastic, it is probably not what wore the flywheel teeth, it is the metal gear that probably spun and spun because it did not disengage. Do not use that starter again, on any engine.
 
I have replaced the plastic gear in starters before with success. I read the original gear was destroyed? What caused it? Did the starter bendix stay engaged and not retract?
I have a few thoughts:
1. You need a new starter or rebuild the original starter.
2. It may not getting be past the compression.
3. Weak battery
4. Degradation of the battery cables or starter cable. Not enough amps getting to the starter.
 
Hello M.,

Now take the old starter apart and analyze the wear damage. It will give you a better understanding of the design. I can say from experience that the armature shaft bushings on top and bottom are worn out, and the armature can be wobbled back and forth
 
Briggs Intek 31P7770348 E1 04052QZA. Picked up a nice mower For 300 a couple years ago. Now I have a starter issue. The starter wouldn't always catch and just grind. then It wouldn't even engage. Checked it out and found the bendix was totally destroyed. Went to the grave yard and got a good starter and all worked good for a day. What I found is It either grids or locks at one spot on the fly wheel. The fly wheel is part #591760. I think the teeth are worn on the fly wheel. It always happens at the same spot on the fly wheel. The teeth either don't mesh and grind or the teeth lock up edge to edge. The picture here is showing the gears in a locked situation. I have 2 junk engines.
3197770377E1 with a flywheel part number 591758 And 31f7070112E1 with fly wheel 693556 My flywheel is 591760. Can I use one of the two flywheels to replace my 591760? Please advise. Thanks , Matt.
Briggs starters have a combination of plastic and metal teeth, plus the number of teeth vary. If you have the original starter that worked properly at one time, comapere the gear material and count the teeth. Just the gear can be purchased.
 
Okay here we go.

Plastic 16 tooth is to use with flywheels with either plastic or aluminum ring gears.
Metal 14 tooth is use with flywheel with steel ring gears.
But this where it can get a little tricky as Briggs later came out with a 15 tooth steel gear.

This is why it is so important to go the engine's correct IPL. as the mounting plates are different enough to cause problems. And using steel on either plastic or aluminum with destroy the ring gear over time.

In this case the pinion gear is a 14 tooth Steel. And those that don't know magnets don't stick to plastic or aluminum but will stick to steel.

And a note on the 15 tooth gear there are two versions. One like the 14 and 16 tooth pinion and one that uses a rubber fiction pad system (lousy design in my opinion).
 
Briggs Intek 31P7770348 E1 04052QZA. Picked up a nice mower For 300 a couple years ago. Now I have a starter issue. The starter wouldn't always catch and just grind. then It wouldn't even engage. Checked it out and found the bendix was totally destroyed. Went to the grave yard and got a good starter and all worked good for a day. What I found is It either grids or locks at one spot on the fly wheel. The fly wheel is part #591760. I think the teeth are worn on the fly wheel. It always happens at the same spot on the fly wheel. The teeth either don't mesh and grind or the teeth lock up edge to edge. The picture here is showing the gears in a locked situation. I have 2 junk engines.
3197770377E1 with a flywheel part number 591758 And 31f7070112E1 with fly wheel 693556 My flywheel is 591760. Can I use one of the two flywheels to replace my 591760? Please advise. Thanks , Matt.
Is that the correct amount of teeth on the starter? Did you compare with old one?
 
Back
Top