Export thread

Add a fuel Filter? Yes or No?

#1

G

GregGA

I've seen some small fuel filters that can be added to my Honda HRX. I think it would be of value. Does anyone use one, and which one? If it's not worth the small cost and effort, let me know your thoughts. Thank you.


#2

reynoldston

reynoldston

GregGA said:
I've seen some small fuel filters that can be added to my Honda HRX. I think it would be of value. Does anyone use one, and which one? If it's not worth the small cost and effort, let me know your thoughts. Thank you.
Click to expand...

Yes its cheap insurance.


#3

exotion

exotion

I run in-line fuel filters on all my mowers like said above cheap insurance


#4

Carscw

Carscw

Yes put one on. Everything should have a filter.

(( cowboy up and get over it ))


#5

Ric

Ric

GregGA said:
I've seen some small fuel filters that can be added to my Honda HRX. I think it would be of value. Does anyone use one, and which one? If it's not worth the small cost and effort, let me know your thoughts. Thank you.
Click to expand...

Most all commercial mowers, even the commercial push mowers all come with a fuel shut off and gas filter if that tells you anything. It would be worth the cost to install one.


#6

G

GregGA

Ric said:
Most all commercial mowers, even the commercial push mowers all come with a fuel shut off and gas filter if that tells you anything. It would be worth the cost to install one.
Click to expand...

Sold. Thanks guys!


#7

exotion

exotion

Carscw said:
Yes put one on. Everything should have a filter.

(( cowboy up and get over it ))
Click to expand...

Ya I buy mine through napa for a buck fifty takes 30 seconds to put in just cut the existing fuel line while still attached insert filter all done :)


#8

robert@honda

robert@honda

Most Honda's mowers already have a filter ("fuel strainer"); just pull one clip and it is inline with the outflow fitting at the bottom of the fuel tank. Remove and clean or replace as necessary...

fuelfilter_zps77f9f1a4.jpg


#9

exotion

exotion

robert@honda said:
Most Honda's mowers already have a filter ("fuel strainer"); just pull one clip and it is inline with the outflow fitting at the bottom of the fuel tank. Remove and clean or replace as necessary...
Click to expand...

Those strainers are a pita.... I remove them and use an inline filter much easier


#10

G

GregGA

exotion said:
Those strainers are a pita.... I remove them and use an inline filter much easier
Click to expand...

Makes sense.
Put it after the fuel shutoff valve


#11

M

motoman

Wal Mart auto section bubble pak if you can't find it cheaper. $3 with clips and hose sections. Transparent. Ran 'em for years.


#12

exotion

exotion

The strainers seem to get clogged a little easier. With the inline filter if you get the see through kind you can see what's in the filter and see the flow of the gas I put it after the shut off so when I drain the tank and run it dry it will suck most of the gas out of the filter. Also the shut off makes it easier to change the filter.


#13

G

GregGA

exotion said:
Ya I buy mine through napa for a buck fifty takes 30 seconds to put in just cut the existing fuel line while still attached insert filter all done :)
Click to expand...

Napa has a see through filter with pleats. It is 3 1/2 inches long. Seems kinda big. Is that the one you are using?

Thank you.


#14

exotion

exotion

GregGA said:
Napa has a see through filter with pleats. It is 3 1/2 inches long. Seems kinda big. Is that the one you are using?

Thank you.
Click to expand...

Yes. Its big but still functional :) on my mowers I just find a place to zip tie them to hold them steady.


#15

S

swimman

Just bought an HRX217HYA yesterday and have yet to put fuel in it. First thing I did was remove the strainer which is very simple (just remove the three bolts holding the pull start/engine cover on and the fuel tank comes right out as it's attached to the engine cover) and installed the pictured filter. Got the filter at Advanced Auto Parts for $5 and bought a little extra 1/4" fuel line in order to provide enough room to install the filter as it's a little large. I positioned the filter on the outside of the control cables as the cables will prevent the plastic filter from contacting the engine or sitting close to the hot cooling fins which as we all know, could result in something akin to a mower BBQ!

The filter does sit outside of the engine cover but I'm not too worried about it snagging. Time will tell but I think this set up works for me as the filter will be easy to change in the future.

Any other tips others can share? Believe it or not, this is my first push/self propelled mower as I just sold my rider in anticipation of moving into my new home with less grass area.

Edit - Filter in picture if positioned the wrong way for fuel flow. I've since flipped the filter.







#16

exotion

exotion

Just make sure the line allows for fuel flow it is gravity fed.

Change oil often, clean/replace airfilter often, change spark plug once a year or so. Keep blade sharp and under deck clean it should last you for a good long while.


#17

G

GregGA

exotion said:
Just make sure the line allows for fuel flow it is gravity fed.

I don't that is going to work the way the hose is routed up, then back down. I could be wrong.

Welcome to the forum. I love my HRX.
Click to expand...


#18

S

swimman

It does work as I started it up and let it run for about 10 minutes. However, I may have an issue when the fuel level drops lower and currently, the top of the loop in the hose is lower than the top of the fuel level so fuel is flowing. But once the fuel drops below that level I have a feeling the engine will quit. I'm going to reconfigure the filter to be in line. The only reservation I have is that the plastic filter will be closer to the engine. It will not touch but I'm hoping it will not melt. Otherwise I better get the marshmallows ready!


#19

exotion

exotion

swimman said:
It does work as I started it up and let it run for about 10 minutes. However, I may have an issue when the fuel level drops lower and currently, the top of the loop in the hose is lower than the top of the fuel level so fuel is flowing. But once the fuel drops below that level I have a feeling the engine will quit. I'm going to reconfigure the filter to be in line. The only reservation I have is that the plastic filter will be closer to the engine. It will not touch but I'm hoping it will not melt. Otherwise I better get the marshmallows ready!
Click to expand...

They are built to withstand quite a bit of heat as long as it is not touching metal you should be ok.. also cut out about an inch of line and zip tie the filter steady


#20

G

GregGA

exotion said:
They are built to withstand quite a bit of heat as long as it is not touching metal you should be ok.. also cut out about an inch of line and zip tie the filter steady
Click to expand...

Agree. The filter is on the opposite side from the exhaust. I held an IF thermometer over most of the engine, and only got temps in the 200F range. My Chonda pressure washer engine runs ALOT hotter: 350f over most of the engine.
I am going to use Rotella 15-40 in that engine. The Honda will be fine with 10-30.


#21

S

swimman

Filter has now been relocated in line between the tank and carb. Straight shot and gravity will allow all the fuel to leave the tank. Zip tied the filter to the control cable to keep it away from the auto choke arm which gets hot. Mowed for an hour yesterday and worked perfectly. Loving the HRX217HYA as it's very smooth - both in cutting as well as rolling across the ground. My 10 year old did our back yard which took about 45 minutes (he walks slower than I would) and was very proud of himself!

Here are pics of the filter repositioned.





#22

G

GregGA

swimman said:
Filter has now been relocated in line between the tank and carb. Straight shot and gravity will allow all the fuel to leave the tank. Zip tied the filter to the control cable to keep it away from the auto choke arm which gets hot. Moved for an hour yesterday and worked perfectly. Loving the HRX217HYA as it's very smooth - both in cutting as well as rolling across the ground. My 10 year old did our back yard which took about 45 minutes (he walks slower than I would) and was very proud of himself!

Here are pics of the filter repositioned.



Click to expand...

Well done:thumbsup: Looks great. Did you remove the factory "filter" coming out of the tank?


#23

S

swimman

Yes, I removed the strainer filter although probably could have left it in as it does no harm but would have to check it occasionally to make sure there are no clogs. Simple to reinstall if I feel the need.


#24

exotion

exotion

Perfect that's basically how I have mine


Footer Links 1

Top