replacement

Hello Everybody! I have this snowblower HST 8613, seller Biltema, see here (link) working just great for several years but now I have to replace one wire. The wire that controls the other track, clutch? I do not know where the wire goes or how to open the bottom of the snowblower. BEFORE I...

i am trying to overhaul this adjustable carb on a tecumseh 9hp snow king. this number is stamped in the carb body. is it a legitamate number? or a casting number? 1433J6X see attached photo, i think i found a kit on ebay. would the 7 ,8 and 9 Hp engines use the same kit?

I have an electric start Honda HRX217K6HZA. Evidently the original SHR3.6-12 12V-2.8Ah batteries are almost non existent! Only thing I've found that will fit IN the battery box is one of these...

I just bought a carburetor replacement kit for my Honda lawn mower, and I can't figure out where this piece goes. Looks like a fuel strainer, any idea?

Toro mower 20065 - SN 280105976 It surges, kinda weak. Still gets the job done but not ideal. Thinking of swapping this one in. Don't know why I got it as it's not exact but that's what I do lol. Can I? Should I just prop it open somehow or anyone got a tip to make a custom switch? And how does...

New'ish to Forum. I am new to old ExMark (pre-Toro) mowers. Have a 2007 unit that blows drive motor seals. Still have original Parker motor that leaks and a replacement motor only lasted about 4 months and now leaks. Both were seal leaks as far as I can tell from owners' description...

After 30 years I need to replace my HRX. I just found out that Honda has discontinued all gas powered walk behinds, what is the next BEST option?

I am trying to find the correct replacement coil for a 1989 L21ZPN. I have shined up all the mounting points mag pick-ups, flywheel mags and the grounding tab. Compliant mower so open circuit to run, ground to shut off handle lever actuated. Cable is good, pulls off the flywheel brake and...

Can’t find 2007 Regent starter replacement

Victa Mustang 18 Ultima 4 stroke 5 hp (1994) lawn mower with Tecumseh engine. I thought the starting problem was fixed by changing the ignition module, but today, after 2 weeks' absence, the same starting problem has reappeared. After priming many times, the engine starts at the first pull, but...

Husqvarna YTH 24V48 Product 960450046 Serial 012315a046880 Hi All, I acquired a Husq yth 24v48 with a blown briggs .The engine is a 24HP 44N877. The shaft is 1' Diameter, 3 5/32 length, 7/16x20 tapped along with a 1/4 inch keyway. My question is : Do I have any options for replacement ? Do I...

I'm starting to tear my GT5000 (917.275972) down to replace a broken ground drive belt and had a question about one of the pulleys underneath. The transaxle pulley and the two pulleys on the right side of the frame in front of it seem fine, spinning freely, but the pulley closest to the PTO...

According to what I have found the engine drive belt is supposed to be 5/8th by 91" so ordered one off of EBay. Now this is not OEM, and I am beginning to believe it may not be the proper belt. I have the PTO and drive pulley removed and in trying to get the belt back on the drive pulley...

The right Spindle failed on my Hopper mower deck. It was a bad failure too. As I dug into this, I noticed these have grease zerks - this tells me a couple of things 1) they do not use sealed bearings in these assemblies and 2) my old buddy who I just got this from, did not grease them. The pully...

Hello, I have a curved shaft Stihl FS 50C trimmer and I hate the head that came with it. My reason for saying that is that it is extremely difficult to put new line on the head and it has very limited capacity. You have to have the finger strength of a gorilla to turn the knob when feeding new...

Recently, I decided to do some deck maintenance on my Cub Cadet Pro Z 100. Two of the spindles (p/n 918-07255) seemed pretty solid. No play in any direction. Before greasing, though, they made a bit of noise when turning the blades. After greasing, they got quiet. The 3rd spindle... had vertical...

I have a 54" ZT Elites and the deck wheels are worn and it looks like the mounting bolts might be a bit bent, so I'm looking to replace them. I normally like to stick to OEM parts, but the squared off design they use occasionally dig in when turning on uneven surfaces, so I was thinking the...

Engine model:123K02-0193-E1 Primer button type carb I've replaced the float, needle valve, and the needle valve seat using all B&S genuine parts. From bench testing everything looks great; I test that everything seals right on the bench by turning the carb upside down and drawing a 5psi vacuum...

Started some work last year on the motor on my L120, didn't keep track of the bolts to reattach the intake on both sides.... Grrr, just get a ziploc baggie... anyway everything is basically a 10mm head but a 1/4-20 bolt seems to fit really well. I'd like to keep everything oem but not if I...

Good morning. My Craftsman GT6000 (917.288612) doesn't want to move forward with the pedal to the metal. I decided it was the drive belt. It should be here tomorrow, but no garage and it's supposed to rain for days. Ugh I watched some YouTube videos, and it seems straight forward. You know it...

The original drag links were replaced at some point in the past with aftermarket adjustable ones. The ball joints are worn on the steering drag link. Does anyone know if a replacement ball joint is a particular (standard) size for this model? Has anyone replaced the ball joint on an...

I have an old Toro Wheel Horse 17.44 HXL Model No.71283, Serial No. 240000104 - Deck may be a Model No.79107 - mows a great lawn. This mower was gifted to me, to use as parts - couldn't help myself - got her going and glad of it. Cutter deck belt needs replacing. Not sure but think Toro Part...

Anyone ever replace one? Will I need to bleed the fuel system after its done? Thanks

What is a replacement engine for a B&S 386777-0111-E1 ?

Hi folks, I have a ZRT50 (model no. 17AFCACP056) and had to swap engines; (Kohler seized - putting in a Briggs). I thought I took enough pictures during removal of PTO, etc., along with the Kohler boat anchor but here I am having just bolted on the PTO to the crank of the newly installed...

I have a B&S 4 stroke engine mounted on an old Mountfield (UK) mower and the fuel tank is badly cracked. The only reference I can find is a label on the side of the tank: “FAMILY 4BSXS.1581VA 276080” Is this enough information to find the part no. for a new fuel tank?

Hello I have a 1989 Troybilt Econo Horse with Tecumseh 6HP engine Model # H60-75505R Serial #SER0066D I want to replace the engine Im looking for any suggestions on what would be a easy and good replacement engine to swap out that won’t brake the bank Thanks for your Consideration

Any suggestions for currently made equivalent push mower ?

I purchased a Pulsar 21" 200cc Gas Push Lawn Mower from my local Menards (https://www.menards.com/main/outdoors/outdoor-power-equipment/lawn-mowers/pulsar-reg-21-200cc-gas-push-lawn-mower/ptg1221drm/p-1642874304916526-c-10112.htm). I've had it for a year, and so far, it's been a pretty solid...

Snapper Model 130.887650 Dual Stage 27" 11.5 TP Snowblower Wanted to replace both driver and auger belts, however could not figure out how to do auger belt as can't quite get clearance to remove drive belt as well as replace new one. The square metal plate on one side and the friction wheel on...

I acquired a 2009 GT2142 recently that had been parked for at least a few years (235 total hours). When I got it cranked and took it on a road test, the driveshaft went to banging and came off. I discovered the blue needle barrels on both engine and transmission end had “collapsed.” I watched...

I have a FD671D Kawasaki 23 hp engine on my Turf Tiger Scags I am going to be needing to replace it in the near future. Starting to blow smoke. Does anyone know if an FD750D will be an exact fit for replacement. So far all I can tell is that the 750 has more HP then the 671. I am aware of the...

I have an Ariens 42" riding mower and the front tires don't have much tread so they slip on hard turns- do the least expensive replacements last long, or should I spend a few bucks more and buy something else? It has Carlysle tires now. Rims are spotless, so I'll just replace the tires.

I have a Ferris IS4500z (Model IS4500ZC28061) - 61" with the 28 HP Cat diesel. Had a catastrophic failure and it looks like a rod broke a playing card size hole through the block. Our local CAT dealer quoted me something just shy of $7000 to replace that engine which is prohibitive but the rest...

I currently have the displeasure of working on a Toro 522xi with a Kohler CH22 engine. While doing service on it I noticed it has a very small headgasket leak starting on the right side cylinder head. (The one with the oil fill port). It's a little hard to say but does this engine need to be...

I have two more hydro brackets broken (again) on my Raptor SD model #937854 and I want replace all the brackets with heavier duty brackets. Problem 1: I can't find any bracket kit that explicitly lists my model #937854 as compatible. Is it safe to assume that all Raptor SD Hydro bracket kits...

Trying to replace a Briggs model 217802 onto a Swisher 44 inch finish cut pull behind with a new Briggs 11.5 hp E1150 model and unsure what fuel tank to use since engine does not come with one. Also how to mount to the engine?

Yardman Model 13AV9YG371 18 hp Kohler, 42" deck A simple main drive belt replacement has caused my repertoire of cursing at the stupidity of the American Yardman "inventors" to increase exponentially over last few days... Yep, like a few you tube blokes show, I'll undo the engine to slip the...

I have a v twin briggs that only needs a single piston. It's a old back up mower and I don't want to spend the money on a set and I already have a new rod and rings. Could I order a piston for a single cylinder engine? Model: 44R677 0004G1

My neighbor lady has this mower and while using the transmission belt broke so the self propelled stopped. I told her I would be glad to replace the belt for her and took it home. I took the covers off and lo and be hold there are 2 bels, a drive belt and transmission belt. You have to take the...

I'm replacing both hydr. pumps in an '08, IS3100Z (with the 26 or 27hp liquid-cooled kawasaki). Btw, I don't see a drain plug on the hydraulic drive units/ motor at each wheel. My goal is to get rid of the old, black oil in the drive units. How? Right now, both pumps are out, and there...

Where can I buy a seat for my wheel horse lawnmower mower¿

Greetings, I’m posting here because I’m aware this tyre has been fitted to a limited number of other machines (Scag for sure) not just my Hustler Raptor 36”. These Grassmaster/turf saver tyres are good however finding replacements in Australia is nearly impossible. The 20x8-10 is a...

The engine on my Toro Super Recycler is using oil. I don't think it will last much longer. The rest of the mower is in excellent shape. B&S made some major changes to the replacement engine. The carburetor and muffler are now on opposite sides ! How hard is it to attach the throttle and...

I have patched my deck as much as possible but it's at end of life due to severe corrosion and previous owner neglect. Each mowing I'm fearful a spindle or pulley mount will fail. I cannot find a replacement deck shell stocked anywhere and have been told that Ferris is no longer building the...

I have a Tvs100-44015b 3.5HP Tecumseh engine that I completely rebuilt last year. New crankcase and piston, valves,etc. Really runs great when warm but having trouble keeping it running when starting cold. I have to keep pumping the primer to keep it running. I am suspect of the cheap carb I...

I have been sharpening my lawn mower blades on an old bench grinder I inherited from my Father in Law for about the last 30 years. I put a new grinder wheel on it when I first got it but now I need a new grinder wheel. The old markings are wore off so I can't read the details type and size...

This is on older Stihl FS85 brushcutter, but any replacement's OK, if it works. Anyone found a good replacement plug wire, metal CONNECTOR tip [?female terminal] (guess style that “crimps" on outside of wire), w/o buying new wire & boot for this or similar equipment? (Pic) Orig...

Hello, I have a Shindaiwa C 35 purchased way back in 1985. Still runs great and I have no issues with it except one. I want to replace the original trimmer head with one of the newer speed (bump) heads currently on the market. My original trimmer head jams more than I would like, so I'm...

I have a Briggs and Stratton engine on a log splitter that needs to be replaced. I got it for free but the engine is locked up due to the old owner running it without oil. Its on a Huskee 22 ton log splitter. Honestly it looks like a push mower engine but I wasn't sure if one would work. I did...