Search results

I went back out and burned the sparkplug clean with my propane bottle torch and reinstalled it, it seems to be running good now its reactive to throttle changes and I can engage the blades. It does seem like its burning some oil, it arrived to the shop non running so I am just getting to see...

I am working on a 06 Bronco with an 18.5hp Briggs and Stratton Intek Single Cylinder, it runs pretty well at idle and when easily giving it throttle but if I give it throttle too fast it starts surging, backfiring through the carb and sometimes will recover if I throttle it down or will die...

917.252450, It's a lawn tractor, with a 5 speed assuming peerless transaxle.

I acquired a 90's model craftsman 2 38" 12.5hp briggs and stratton riding mower. I'm going to replace the spindles, deckbelt, battery, fuelline, air cleaner, and change the oil. It runs and drives good, brakes work. After I do the work what would you value this machine at? The paint is mostly...

I've got good contunity from ground to the black wire, 622 ohms from the red wire to ground and 622 ohms from the black to red wire. Junk Stator? Or is it possible the diode is bad?

No regulator, just a diode before the plug. I will check for continuity.

I recently acquired a commercial size pressure washer with an 18hp Briggs Opposed twin, it needed a carb clean and fuel pump kit. I got it running and it runs pretty well but it's not charging. It's got a heavy duty push button starter switch on it I saw they had the charging wire connected to...

Okay, looking at them again they aren't as bad as I thought they were after cleaning out the old bentonite,but they could still be the problem. The axle shafts also had some up and down slop and the input shaft bearings are toast.

I have a Stx38 with transmission problems, it won't move forward in any gear it just pops and makes a rapid clunking sound, everyonce in a while it will catch and inch forward. It's acting like something it stripped or slipping but it will move in reverse fine. I removed the transmission from...

Okay, Ill have to pull it apart and take a look.

I've got an L100 that has developed a rod knock, on John Deere's part breakdowns all I see them sell is a connecting rod, no rod bearing. Do I have to replace the entire rod? If it's something that's not fixable I will just run it till it blows up since Ive got several other engines that could...

Sorry for no reply, I got busy with other projects but I got back to this mower tonight and I was going to swap the engine out for another one since I have a whole barn full of mowers. When I pulled the engine out I heard something rattling around inside, so I opened the case and it was the pin...

For some reason when I try to upload pictures it says the file size is too large.

Okay, I didn't think that o ring was supposed to be there.

I've tried doing that and it didn't change anything.

I was given a Yardman 42" mower with a Kohler CV16S, the guy told me he replaced the o-ring on the governor shaft and now it revs wide open if I put it in full throttle. Like wide open it will blow up, when I return the throttle to idle it idle's no problem. When I start the deck the rpms drop...

I was given a Yardman 42" mower with a Kohler CV16S, the guy told me he replaced the o-ring on the governor shaft and now it revs wide open if I put it in full throttle. Like wide open it will blow up, when I return the throttle to idle it idle's no problem. When I start the deck the rpms drop...

I was given a Harmony 2013 Riding Lawnmower, the Previous Owner said he stopped using it because he was tired of having it worked on he said it had been to the Honda Dealer 4 times at least for issues with starter sims, Does anyone know anything about this? When I first tried to start it the...

I was given a Harmony 2013, I got it running and mowed the yard today. All was good until I was almost done I disengaged the PTO and the belt threw all the tension around the engine pulley and the belt fell through the peg that is supposed to hold it on. I put it back on and it did it again. I'm...