Search results

It's probably #000001

This is VERY good advice. My sentiments exactly. Water is your equipments worst enemy. Also, one of the worst things you can do is cover a piece of equipment with a piece of plastic or a tarp if it is setting on a dirt floor even inside a building. Moisture comes up from the ground & is trapped...

Thanks for your input.

Make sure each pulley is turning freely & belt is on correctly.

You might look at the Scag Cheetah & the Exmark.

P Make sure belt & all the belt pulleys are turning freely.

I have a near new Scag Cheetah with 27hp Kawasaki I got it out of my shop & mowed the yard. When I took it back to the shop I could not get off the seat without engine trying to die. I checked all the safety switches & they all seemed to work properly. Then it would not start. I checked the PTO...

If you have a Kawasaki 25 HP that the air cleaner looks like this, You need to read <THIS LINK> They designed the cover to clear the air cleaner with 1/2" clearance, then put on a foam pre-filter that's 1/2" thick, cutting off the air on half of the filter. To get full use of the air...

KK, I cannot thank you enough. I did as you said and the clutch fell off within one minute. You saved me 2 x 60 mile round trips to shop & at least $100. I forgot a problem I had back in 1965. I was replacing the tie rod ends on a 1960 Volkswagon. I pried and beat with a big hammer for an...

I need some help from a good mechanic. I have a 61" Great Dane Chariot with a Kawasaki 25hp Engine # FH21VB09436. The lower bearing on the clutch that engages the blades has locked up. I removed the bolt that holds the clutch on & had trouble getting the clutch off, but finally got the...

My 25HP Kawasaki has an oblong paper air filter and a foam pre-filter over that. They are both pretty expensive and get dirty quickly. I add a wrap of 3M Vetrap over the foam cleaner and then replace it often, saving the pre-cleaner and the paper cleaner from getting so dirty so soon. The 3M...

1973 is not so old. I have a 1960 Lawn boy with grass catcher I bought new in 1960. It runs good and I use it every year to mow around the back door of the house. I always cut off the tank valve and run it until it dies. I then turn it completely upside down to empty the tank. It usually...

I have a 60" John Deere lawn Sweeper that I bought probably 15 years ago. We lost all of our leaves last night, so even though the sweeper has never done too good at picking up leaves, I decided to give it a try, pulling it with my 60" Great Dane ZTR mower. The wheels driving the brush were...

Looks like a good job for one of those computer hard drive magnets I have been saving. I have found lots of other uses such as hiding spare car keys, stick one on oil filter to trap steel particles in oil, finding that nut I lose in the grass......the list goes on and on. :-) Here is one in a...

The Great Dane Chariot 61" has a terrible system for setting the deck height. It has a pin with a knuckle-busting ball that is hard to change to a different hole. I made a plate with notches and then a dog to drop into those notches using the existing lever handle. It is really easy and fast...

Here are photos of the tension springs and chain on the mower. A "U" shaped pin is inserted through a chain link to lock it into place. I tie up the excess chain after adjustment is made. I left the chain long so I can hook it onto a come-along and tighten or loosen it.

My Great Dane Chariot 60" Blade Belt Tension Spring (part #D28025) broke so I got a OEM spring on the 'net for $25.00 and replaced it. Eight weeks and about 30 hours of use later, the new one broke just like the first one did. The spring has a hook on each end and one of there hooks broke off...

I have had my 60" Great Dane ZTR W/25hp Kawasaki for several years. About the only complaint I have had is they put the oil drain valve on the left side, behind the battery. That engine has a tap for the drain on both sides, so I bought an oil drain line made for the Exmark W/25hp Kawasaki and...