Search results

Thanks for that! I just placed an order.

Well, there's a story there... I've actually been to Autozone three times in the last week, first to get studs (that didn't fit), then to get a puller because the one I had wasn't large enough for the hub, Then to go back in an attempt to get larger studs, which they didn't have. Then I placed...

They're the right size (1/2 x 20) but they're not wide enough at the "head". They spin around in the hub because of the smaller diameter. You may be able to spot the difference in the image above.

Here's what was sent to me compared to the original stud.

No, nothing is there. I know it dates from about 2010 based on other manufacturer's stickers.

I've looked all around my Hustler for a label that has the model number on it and can't find it. I know it's a Hustler Super Z 60" deck with a Kawasaki FX-850V engine. I'm trying to replace the wheel studs and can't find the right size for my hub, and my yard is really looking like a jungle at...

Same problem. How do I get this damn thing off???

So, here's the latest. I unplugged and cleaned every electrical connection I could see. Now the engine starts up without blowing the fuse, but it continues to die after 3 seconds. I'm guessing I had two separate issues. Any suggestions for the dying engine? Again, I had replaced hoses and...

Looking at the owner's manual, there appears to not be an oil level sensor, or what Kohler refers to as "Oil Sentry™ oil pressure switch monitor".

It starts back up most times and then dies again. Sometimes the fuse blows right away and other times it works for many starting attempts.

I have the above engine in my garden tractor. I have a snow-thrower attachment that I use to clear the driveway. Lately, when I try to start the engine, it'll run for about 3 seconds before dying. No problems for many seasons prior to this. Oddly, there is a 30 amp fuse that keeps blowing as...

Ugghh, I got the old clutch off, but my replacement clutch has the bearing upside down and isn't compatible. :rolleyes:

Thanks, Richie. It's good to know it should just slide down.

I'm having trouble with our clutch that engages the blades on our Hustler Super Z. Lately, it is not engaging the blades right away--sometimes I have to drive the mower around and suddenly they will engage. I took out the shim hoping that would solve the problem but it didn't. The electrical...

I'm having trouble with our clutch that engages the blades. Lately, it is not engaging the blades right away--sometimes I have to drive the mower around and suddenly they will engage. I took out the shim hoping that would solve the problem but it didn't. The electrical wiring looks good and...

Got the engine started this afternoon. Thanks everyone for your help.

I'll have to check. Thanks for the suggestion, although I'm not sure how that would have suddenly changed.

Hustler Zero Turn "Super Z" 60" with Kawasaki FX850V engine.

When pulling up on the switch to engage the deck blades, they don't start to spin right away. Sometimes it takes 10-20 seconds for them to 'turn on'. This is a new problem. I replaced the switch but the problem is still there. Any suggestions?

Thanks, guys. I'll do a more thorough job with the carb and check into the solenoid if that doesn't do it.

I've got a Kohler Pro V-twin 27 hp engine in my Craftsman DGT-6000 riding mower. It's been sitting for a while, and I finally got around to trying to get it started. I can spray starting fluid in the carb and it starts right up but only runs for a few seconds and dies. If I try to start it...

what do you do when this happens and you're trying to disassemble the carb to clean it?

I have a Hustler Super Z zero turn mower with 60" deck and kawasaki engine. Lately, the mower loses power when under any load (accelerating or going uphill), and when cutting grass. It seems to have come on fairly quickly, and when I first noticed it, the mower was running weakly until I heard...