Search results

any update to your issue? I'm following and curious as to the resolution.

Yes, for sure and at that point, in my diagnostics, where it doesn't fire, is where Step 5 would be, to pull the flywheel and check the key. In my pre-diagnosis, before I do anything, among other items I look for, I check the condition of the blade. If I see a big divot out of it, and the mower...

I've been fixing small engines now for just a couple of years as a hobby and have picked up lots of things along the way. With the problem that you are having, here is what I would do in this order 1. the very first thing I check for is the oil to find out what condition it's in or if any exists...

So, do you have an update for us? What did you find as the problem and solution?

I ran into the same thing last summer, bad pressure switch which, when working, will open the solenoid on the carb to allow gas to flow.

Is it possible you have a new 'bad' coil? I keep the following as a reference Coils and resistance measures B - base K - kill S - spark B - K 2k - 18k B - S 2k - 18k K - S 10k - 30k Mower coil Red probe to Spark boot Black probe to base ground Should show 2.5 to 5K If infinity, then the coil...

Good morning, I know have package but it contains two keys. Pics attached. The only piece that I see that was still in the slot on the mower was the bottom key in the package below. Is there a particular way to put it in? Are both pieces used and if so, how?

Great, and do you know that engine model by chance?

I have a Mastercraft Model: 113-413E515 mower that I am trying to figure out what key I need. It’s a Tecumseh engine but I can’t find any model number on it which is strange. I bought a kit of keys but the one that would fit in the slot appears to be too small or not the same as the original...

Good morning, I still do not have this unit going. The lines are correct now, it does start and run for a while but only on half choke. After it's been running for about 15 seconds, if I open the choke wide or close it completely, it will die. And saying that, after about a couple of minutes, it...

Thanks for all the recommendations.

thanks for all the advise. So, will something like this work for me then? And if it will, is it a case that I aim it at the spark plug?

I was thinking of getting a digital tachometer because there have been a few machines in the past that I've worked on that 'appear to me' that they maybe running a little too fast. Also, if I were to purchase one, they are very cheap $25.00CA from Amazon. My concern is that I will purchase one...

I have a Homelite UT-20700 weed eater and there are parts missing for the head. I thought I ordered the correct parts but when they came, they were completely different than what is on the head. On the handle, there is a model number: D825SB. When I look that number up, it does not cross back to...

thanks everyone for the advise. Today, I will take my notes out and confirm everything and repost my results. After I read ILENGINE, I went out and reversed the hoses but I didn't start the unit up as I had other things on the go. Again, today I will get time to spend with my favorite weed...

and here is a picture of the original unit when I took it apart

ok, thanks for this. I have worked on many weed eaters and this one with the remote bulb has got me confused. When it came to me, the hoses were broken and on the internet, there are no pictures of how those hoses should be connected with the remote bulb. Also, if I can't get this carb working...

at idle, it ran great, hitting the throttle, it was boggy and tried to stall. let off the throttle and went back to idle and eventually stalled.

Hi all, I have a Weed Eater Poulin LT7000 that I am having some issues with. The unit was brought to me not running. After replacing fuel lines and filter, fuel bulb, diaphragms on both sides, metering diaphragm, plug, and fresh mixed fuel, I started it up and it ran great for about 3 minutes...