Search results

Need help installing a headlight assembly. How to install/reinstall the hood? Is it better to remove the front grill first? Is there a service manual available ?

I have a zt740 Confidant engine. Would it be beneficial to use the 300 hr oil change kit? I am presently using their yellow filter and 10w30 semi synthetic oil.

Need to replace coil. What is the air gap clearance ? Thanks in advance

ZTX5 54” What should be the torque settings for blade nut and spindles? Is thetr a better spundle assembly than the one Cub offers ?

Got a ZTX5 with squeal with blades engaged. You can hear it slow down as rpm’s lower to stop. Can’t tell if it’s idler or spindle. Only has 60 hrs on the mower. Just wondering if there’s an issue with any of these parts that’s prone to failure.

ZT3200 pumps. Cub manual recommends 200 hrs before changing Hydro oil, I think HG recommends 75. Any one have any input on this subject?

Motor is extremely loud on my zero turn. Do they have anything available to quietness it down. It’s on mt ZTX5 Cub.

My ZTX5 has a Kohler ZT740 engine. Seems excessively loud to me. This may be normal but just checking see if anyone else had noticed. Do they make anything to help reduce the noise? Wonder if they make a quitter muffler. Don’t know who supplies their mufflers.

ZTX5 with ZT3200 Hydro Gear pumps. Anyone used their kit to change fluid ? Thinking about doing it myself. Just wondering how difficult it would be.

ZTX5 with ZT740 25hp Kohler with 15 hrs. Full throttle or idle down for stopping engine . I’ve been lowering throttle to idle and I’ve noticed it’s either backfiring of after firing when I shut it off. I’ve been told to shut down at full throttle, mid throttle, and, idle.

Need a service manual for my ZTX5 Cub. Thought Cub Cadet would have one available. Thanks in advance.

Just finished changing the break in oil on my ZTX5 ZT740 Kohler. I used a funnel with a strainer. First qt was ok. Second quart found a piece of gray plastic in the funnel screen, same color as the bottle. I used Kohler 10/30 semi synthetic. Glad I found it. Blue cap is for reference only.

ZTX5 ZT740 Kohler. Changing break in oil in about 2 hrs of break in time left. Thoughts on which oil to use ?

What’s the recommended tire pressure for a ZTX5 54”? Not in the manual.

1. Any one else notice an extremely loud deck/blade system with blades engaged? Just wondering if that’s a known issue? Also, do they make shorter lap handles? Still a little high all the way down. 2. What is the weight of this mower? 3. Easiest way to lift mower to change blades without deck...

Please delete wrong forum.

The bottom hole in the deck wheel bracket on my z540m is rounded and I’m unable to to tighten the 13mm nut without it spinning. I know I could move it up one but I mow between 3 - 3 1/2” height. Any suggestions on how to repair it ?

I have a Z540M with a Kawasaki FS730V. I have an occasional puff of white/blue smoke after restart on a warm engine. I use full throttle on restart, as recommended my owners manual, but, wondering if I’m dumping too much fuel with the full throttle. It would probably start on the the low...

I have the blades that came with the mower (M143520). Just wondering if the high lift blades, or, mulching blades would be any better? Would like to find one to cut up leaves better than what I have.

How do you adjust the valves on this trimmer? I have the gauge.

I’ve noticed it’s very hard to crank the engine while pulling the rope. Lot of resistance. You have to really hold it down while trying to start it. Is this normal?

What is the difference between a FR730V, and, a FS730V engine ? Is one more reliable than the other ?

How do I adjust the idle on my Z540M zero turn ? It has the Kawasaki engine.

I removed the cylinder cover and am concerned about which single screw goes back in the rear offset mounting hole facing the trimmer head. There are two different ones and I don’t want to mess up the threads. The parts diagram shows two possibilities: 1. 503216820 Ihscft screw 2. screw Ihscft...

What’s the easiest way to remove the throttle cable from the carb without removing it ?