Search results

I am replacing armature on a kohler starter 2009811-s and I am having trouble holding the 4 brushes in so I can put the armature in the end piece. How do they do that thanks.

I am replacing connecting rod on a Kohler 21 horse courage engine but can't get socket on inner rod bolt. The counter weight balancer is not allowing me to get a socket and wrench on the bolt. The engine is model sv600 spec sv600-0009 serial 371311993

I have a briggs 19 horse on a yard machine rider and the engine is quite loud. I have a round muffler which bolts to a short pipe which is bolted to the head. The muffler and pipe are good but as I mensioned it sounds loud when it runs. The muffler comes out of the engine on the right side and...

I am working on a Cub mower which has a Micki carb 698620 and I took it apart and cleaned iit but it still serges. If you hold the throttle with your finger it runs better. I have another enging with that same carburetor on it which does the same. They are a bad design carburetor that briggs used.

I am putting a new starter in a Kohler sv590 and the new starter has a tab that sticks up near the studs and the starter won't seat right because the tab hits the piece that the studs are supposed to go through. The old starter did not have that piece.

I have a husqvarna k750 which has new cylinder, piston and rings and new crank seals. It will run if you squirt fuel in the sparkplug hole but it does not seem to suck the fuel up from the tank. The fuel filter is new and fuel is getting to the carb when I take the line of f fuel runs out of the...

I am working on a mtd snowblower with tecumsah 10 horse on it model lh358sa and when I prime the engine with starter fluid it keeps running fine. I shut the engine off and try to start it a few hours later it does not start on choke or by pressing the primer. I tried another carburetor on the...

I am trying to put a mower deck on a gravely 1138g and the diagram I got does not show how the 2 arms go or how the lifting carriage goes on the deck or the mower. Where can I get a picture of the entire assembly thanks.

I am working on a scag z mower and when it is running I get a rattling sound but it is not from the engine. The drive belt shows sign of wear on the wide part of the belt. How do you access the top drive belt pulleys, there is no room underneath?

I am working on a twin cylinder briggs 23 horse engine. I am trying to replace the crank seal on the power take off side of the crank. I am having a hard time getting the seal on the step part of the crank where it gets wider. Once I get it past that part I can tap the seal on with a plastic...

I am working on a Bradley 48 inch walk behind hydro mower and there is no room to get behind the engine bottom pulley in order to get the mower belt off the pulley. The belt guide and idler is not acdcessiable. Is there something I am missing?

I am working on a briggs model 21t202 and am replacing the connecting rod and I would like to know which way does it go on the piston. I know the arrow on the piston goes toward the flywheel.

I am working on a briggs 286707 engine and I replaced the sump gasket with a 15 thousands gasket. After I tighten the sump bolts the engine turns hard. If I loosen the bolts it turns easier. There is no shim on the crank shaft about the gear so not sure what I have no end play with the crank shaft.

I tried a left handed tool from echo but it does not screw in to the plug to remove it. I also try to drill the plug gently but it screws up the slot in the adjusting screw. How do other people remove those plugs. thanks.

I have a small tiller which has a small wead trimmer engine on it and I replaced fuel filter line and carburetor and when I start it up it idles fine and will accelerate slightly but when I put it on full throttle it bogs down and stalls. When I put on the choke slightly it will run full speed...

I have a Echo pb413h and I put new carburetor on it and cleaned the exhaust and it idles fine but will not rev up high. I also replaced the fuel lines and it still won't adjust on high speed to speed up higher.

I have a x mark with 25 horse kal engine on it. I cleaned the carburetor and replaced the coil on the side that was not firing and adjusted the valve clearance. it fires on high speed but it miss fires on slower speeds. The compression is 150 on the side with the miss fire.

I am looking to buy a titanium ez flux 125 amp welder. and I would like to know if the welding wire is live all the time or only live when you press the trigger. I am blind and I would like to position the wire on the part that I want to weld. I bought a Chinese welder and with out pressing the...

I am timing a briggs 446777 twin cylinder engine and the crank gear has a dimple on it but the cam gear has a line and a dot. Which mark do I use for cam to crank timing thanks.

I am working on a John Deere lt155 with 42 inch mower deck. When the deck is all the way down the mower belt is loose like it should be until I engage it to mow then it tightens up properly. When I put the mower in transport mode with the deck all the way up thhe mower drive belt tightens up...

My sister wants to buy a lawn tractor so she can use it to pull a cart for hauling rocks and general hauling around her yard. The yard has also has a steep incline and she is not sure what to buy because the transmissions on lawn tractors are not made for hills. I was wondering what people would...

I am working on a briggs 12 horse with a nikki carburetor on it. The engine runs fine but when I prime it to start it once it leaks out of a hole that is above the fuel line fitting on the carb.