Search results

Working on Poulan Pro Mower.. I need a parts diagram and an OEM parts source..... appreciate y'all's help!

My Z50 EZT gearbox drives have two flat side that fit into the axle hub. There is "slack, movement" between the flats of the axle and the wheel bore itself. I'd appreciate ideas as to how to tighten up the wheels/hubs. Things I have considered: 1. Spot weld the axles, file down to fit the...

Crafty spacer technology 🤣

I want to "drain" oil in my Gravely Z50 with EZT drives...........without pulling units off, how successful will pumping the fluid out with a pump from the fill plug? Will I be able to get most all the fluid out this way, short of disassembling the units? Thanks in advance, bartles

Working on a 407577-0292-E1: B&S site says cylinder head no longer available. I need to locate a head with the guides installed...appreciate help in advance. bartles

Model: 407577-0292-E1 Anyone got a clue what this is.....you can scratch through it....but resists chem-cleaners and varsol. It runs from the dipstick tube hole to the top of the crankcase.

I'd appreciate someone letting me know the bore specs for a Model 407577-0292-E1. Thanks in advance, bartles

I'm rebuilding a Gravely ZT50. It has a B&S model 407577-0292-E1 that the previous owner chose to replace the the "as shipped" Kawasaki. As I look at the different alternators available I am unable to determine what one I have(black and red wire). I'd appreciate advice on what amp rating I...

Working on a Model 915144/ s/n 001766. The previous owner has really tried his best to: HotWire, ByPass, or use as much black tape as possible to get the machine to run. The harness is a mess. Toying with just buying a new harness($116). I am first going to be sure the engine is ok. Can...

Have a guy with a 60" Hustler mower, model 934778, 450 hours running time, with a deck , part #552269, that is so rusted out the entire top of the deck has to be replaced. Including the cost of plate he is looking $1500+ from me to do that. Any suggestions where he might locate a used deck?

Can anyone provide the model number of the B&S engine on a Sears: Model 247.288851/Serial Number 1A281B10208? Owner left town on a cruise and I want to work up a parts cost for an engine rebuild (provided taper isn't too out of spec) before they get back.

Working on a Bolens/MTD Model 11A-B06R765(has a number 421852 under the model # ) s/n 1G253K10481 Mower's recoil came to me in pieces off the mower....I ordered a new starter that came with a "insert" looking piece with a 4 bolt pattern loose. The replacement starter appears to snap into the...

Working on a "very experienced" Yard Man 38"/12.5 HP B&S The model on the tag under the seat is: 13AT674G401(the seat must be from another model MTD) The tractor has a totally different deck belt/pulley arrangement than what is illustrated in the MTD website. This tractor has the cable...

Asking for confirmation the resistance reading for a good blade clutch should be 2-4 ohms, right? Thanks in advance, bartles

I have a totally rebuilt Dixon mower for sale, whole or parted out. I got curious about these mowers, their propulsion system, and history and ended up restoring this 30". Shipping the complete mower is probably a reach but i would entertain parting it out for shipment that way.

Working on a JD LX 277/ MOL277C061290 with Kawasaki Code FH500V-BS11: Owner was mowing when the fuel line from the fuel pump (or from the carb "overflow" line) to the carburetor evidently leaked fuel down to exhaust system starting a fire that melted the carb ground wire, overflow line, and...

I realize this is not an application discussed in a lawnmower forum, but I need some parts locator assistance: The B&S engine powers an auger, its model number is 126M02-0122-F1. There should be a spring between the throttle control link/lever and the butterfly shaft that balances with the...

I'm working on Hustler with a blurred ID tag...I think, s/n 1B01OH20162 What's the model number? Year built? Kawasaki engine code: FR651V-AS05-12 Thxs in advance, bartles

Working on a Toro Model: 75754, Engine Model 139-0602 The complaints and observations are: when deck is engaged the engine "bogs" down almost to a stop but will regain rpm. Low power. Exhaust smoke. Oil in muffler outlet. I did a compression test on both cylinders: both tested out 150-160...

The stamped model information on the rocker arm cover is no read able butvI have a photo of the serial number attached Thanks in advance, bartles

Working on a Sears 42" Mode 917.276181/ SN 042006D001017 The fuse located in the wiring harness has 15 amp rated fuse(blown). The parts listing in Sears Parts Direct indicates the fuse rating should be 20 amp. Looking for confirmation of what the amp rating please, bartles

I am getting "pushed" to other than the OEM site for Hustler parts.... What is the official website address for Hustler parts?

A Briggs Model 254707 Code 0120-01 Several years ago I restored an old, 1973-4ish Dixon mower for grins....what a mechanical marvel it was/is! Infrequently apparently the float valve sticks open totally flooding out the engine. I have an inline filter and shut off valve between the tank and...

Working on a Model 934778 60". The mower had a broken drive belt. I replaced the "broken" drive belt and the idler pulley. The belt, cogged, look hardly used, and the idler pulley bearing was tight. I put a new belt(cogged) on along with a new idler. I started the mower up, warmed it up a...

Working on Hustler 60" Model 934778.... Need suggestions for repairing plastic fuel tank. I haven't seen the leaking area but according to the owner its about middle level tank. Thanks in advance, bartles

Working on a PS-SV620-3215.....should the baffle be sealed inside the valve cover? My gut says yes but....?

Beginning a second like rebuild on Sears YS4500 with a Kohler PS-SV620-3215/ an 4305109533 and would appreciate any heads up what to look for advice on the Kohler. Its got 100psi compression and I bore scoped the cylinder and see a good cross hatch pattern. What are the valve clearances...

Working on a LT1045, new to me. I was having fuel feed issues so after all the usual suspects were cleared, i.e. carb, fuel pump, flow from tank(trickle) I peeked inside the tank with my borescope and found trash from the fill cap sealing gasket and a fuel nozzle! This was a first for me.:LOL...

Working on a LT 1045, Model 13AX11CH712, S/N 1A115H10684 Looking at a new owners deck, without a history, and I do not see a way the deck belt keeps tensioned I see in the parts listing a couple of brackets with the same parts number, 783-05118 that appear to be bolted, sandwiched, together...

Need help locating model number. I can not locate the model number I need to look up parts. None of the linkage involved with controlling the self propel are on the mower. It looks like there were tags on the gas tank. I can see a small tag on the transmission that has "130-6733" on it...

Working on a 42" Hustler model 927368/ SN 05011533 Helping a friend with his issue: When he turns blade clutch on the engine dies.......mower was operational until this problem developed. I would appreciate help with where to begin the problem search. Fuses are good. Thanks in advance, bartles

Working on a Model 927368, 42" The existing deck is eaten up with rust. I can patch it but I would rather get a reasonably used deck. The local dealer says a new deck(part number 546929 is no longer available from the OEM. Is there a source out there........minus E-Bay I've look through...

Working on a Hustler Model 927368. The owners manual says "units are not serviceable...sealed for life" I'd appreciate some advice about how the life of these units could be extended by changing the oil and possibly a filter/strainer.

Id appreciate so maintenance instructions for the subject drive units, i.e., fluid/strainer or filter replacement recommendations, and sources for those parts. The units fit a Model RZ5424. Thanks in advance!

I apologize ahead of time about a picture not being available. I haven't figured out how to reduce the size of pics taken with my phone. On all engines new to me I prepare to start for the first time I take the starters apart to inspect the brushes, clean up the armatures and lube the...

I've rebuilt maybe a half dozen 31R 707 0154 E1 models(or models similar to). Installing the oil pan and knowing the oil slinger is in its right place with the cam always increases my BP😁 If anyone out there has a technique to share oh please enlighten me. bartles

Received piston with ring set, part number 594539 for a 31C707 0254 E1...the two top rings have color code markings...can someone advise(mounting order top down) which color ring fits to the piston?

I am replacing a 10.5 HP 21R707-0145-G1 with an older 17HP 31C707-0154-E1. When comparing flywheels I see a difference, when the magneto magnets are between the block mounting holes for the magneto, of the flywheel keyway positions. The 31C keyway is roughly located at 2 o'clock, and the 21R...

Working on a 31C707-0154-E1 What is the allowable clearance between the links and the crankshaft? Thanks in advance, bartles

Throwing this out here for an opinion(s)....will a 17 HP B&S run reasonably well with a 10.5HP intake/carb system? Re-jetting the carb required? The small engine has a ventilated block. The 17hp engine has the same footprint and general fit up requirements. I was thinking of using the 10.5...

Working on a 42" JD deck who's owner ran over a "piece of metal". The bore for one of the spindles in the deck is bent and has hair line cracks in several places. I have been able to beat the area around the hole to a relatively level surface. I've welded up the cracks from both sides. Any...

Working on a 2020 Murray 30" with a 10.5 HP B&S. The block has a hole in it courtesy of the rod and associated trashed crankshaft. Engine: 21R707 -146-G1, Code 190925ZD Haven't priced out the part yet but, basically, should I look for a "will fit" engine, search EBAY, or ...

I was given a L120, GXL120A014009 with a B&S Model 406777-0128-E1. It looks to be a rebuildable core: good compression, engine runs relatively smooth, check the cam lift(s) for worn lobes and the transmission works fine. The 48" deck was not installed but has good metal. I have a couple of...

Is their model 406777(0128 E1) one of the vees that have had cam lobe wear issues? bartles

I started to restore a joystick controlled Snapper Zero Turn but the deck was just too far gone + I learned the drive units were no longer serviceable. I can confirm the drive units are in good condition because I drove the mower around to get them warm enough to confirm they are in good...

What is the year built of a : PA-SV735-3021 s/n 4217706133 ? Thanks in advance, bartles

Ok, I've rebuilt dozens of small engine starters. I bought a "Far Eastern" starter and this was packed with the terminal nuts...what is it for?

I can't locate what the valve lash clearances should be for a Honda engine, GCV160LA0 S3B NH1. Hope someone out there will have those! Thanks in advance, bartles

Working on a Model HU700H, 961450024 01 I need to replace the rear wheel flange bearings as well as the drive pinion bearing in Part No. 585281901(adjuster). The bearings are not listed as an available part in Husqvarna's website. Thanks in advance, bartles

I was given a Sears TYS4500, model 917.289903 with a 26HP Kohler Spec: PA-SV735-3021. There's always a story with something given away. The givers neighbor bought it new and very soon after it was delivered the engine "failed". Sears came out and replaced the failed engine under warranty...