Search results

Part no. 532176031

My X1901 2000 vintage Dixie Chopper runs like a champ. Though it is not the orginal engine. Orignal engine was a 19 HP Kawasaki. The engine on it now is a 2006 CV20 Kohler I took off a perfectly good Craftsman Garden Trractor. Never regretted it though.

We use and sell a lot of tygon fuel line. For molded hose you need to go back to the OEM or places like https://ahlbornequipment.com/ They have a lot of parts for Chain Saws.

Nice machine. Good luck selling it.

You can buy a jumper with the diode in it. Dixie Chopper makes one I know. Don't have access to the part no. now but can get ti.

Not all brake clearner will work. CRC in the red can will not work. Have not tried any of the others since I use Gumout carb cleaner.

https://services.generaltransmissions.com/wp-content/uploads/pdfs/service-manuals/39008-D1%20RS800%20P.pdf Try this

We it boggs the engine do it could be the clutch bearings trying to lock up check to see if it is making a noise.

What color is the pto switch red button or yellow. If Red I would replace it with the new yellow 679534 switch. When you have it off take a look at the terminals in the plug and see if the center tabs in the terminals are broken out.

You did not idfentify the mower type and model no. as that could make a difference as to what the problem is. Hustler, Big Dog, Dixie Chopper all have models that have problems breaking the Hydro mounting brackets causing the problems you are describing. Check the hydro mounting brackets.

Look at the top of the carb where the Idle circuit welch plus are to see if one has come out. A common problem with these carbs.

post model and spec # and we can help U find the direct fit engine.

I have a Magna Matic and it balances horizontal and turn it vertical it will go back to horizontal. Never really though about it but tried it when this post came up. Seems funny but that is the way it works.

Goes in the fuel tank of something has a filter and float for a fuel gauge don't know what kind of tractor it goes on though. Probably for a farm tractor.

I think I did contribute to the information you ask about and what could happen if you didn't. "The brakes won't hold a mower on a trailer due to bouncing of the trailer. Best to strap it down. If you are involved in an accident and the mower comes off the trailler and causes damage it is your...

The brakes won't hold a mower on a trailer due to bouncing of the trailer. Best to strap it down. If you are involved in an accident and the mower comes off the trailler and causes damage it is your fault no matter who caused the accident. Strap it down and be safe.

Check the exhaust port as well they can clog too.

https://xtremeope.com/ best clutch out there never had to replace one yet this all we sell when they make one to fit what we are working on.

Try tightening the axle bolts but not to point to where the wheels won't turn freely.

Detail FX1000V [Carburetor and DFI Models] andFX921V Engines may experience broken exhaustvalves and/or camshaft lobe wear. Cylinder headand camshaft kits [with related sub-assemblyparts] have been made available to eliminatethe possibility of part malfunction during engineoperation. Kawasaki...

Didn't say I would just what it would cost if decided to fix it.

Might what to check and see if the head is flat. I take a large piece of artifical granite and emery cloth and lap the head. Use 400 grit emery cloth. You can use a piece of glass it works as well.

Have a Dixie Chopper Classic 3160 2014 model with a FX921 Kawasaki in the shop that we were doing a service on the mower. Heard the valves rattling and went to adjust the valves. I was amazed at the clearance it had on the exhaust valves. One was about .030 and one was .075 and it ran just fine...

We get mowers in all the time with loose oil filters. All makes and models with all types of engines. Expansion and contraction due to heating and cooling will make the gaskets shrink and cause it to leak.

We have received some isolated reports of oil seepage/leaking at the base of the oil filter. The condition is usuallynot evident until the engine has been run.The filter manufacturer uses oil as a lubricant when the end cap is crimped into the filter canister. In some cases,excess oil was...

I remeber when you got a 42 inch cut with an 11 hp Briggs on it. Now you have to have a 18 or 20 hp engine. Over Kill

Briggs and Stratton now owns Simplicity depends on how old it is as to who made it.

Planed obselences

That would be a good place to start. U need to determine why it is quiting.

It is a 3 amp charging system and not enough to keep battery charge and run electric clutch. You can change it by putting the stator for the 10 regulated system and the 10-16 amp regulator on it.

Does the Briggs have a regulator on it and if so how many wires does it have? Does it bolt on with one bolt in the center of the regulator or two on the ends?

Don't know if they do Kohler engines or not you may want to check this out. https://millennium-technologies.com/cylinderrepair/

It says some CH25-26 engines. Those are horizontal shaft engines. Did it also say CVs as well?

The problems will be as you stated the shaft size and the charging system. You can put a sleeve over the crank shaft to make for the correct shaft size. The charging system will need to be probably a 10 amp system...

CV25 with nickasil cylinder liners? Never saw a CV25 with that all I have ever seen have cast iron liners.

Religion is like this if you ain't sinning like I'm sinning you ain't sinning right. Good gosh I started this thread and it has turing into a pissing contest. I think it's about time to shut it down.

Right no 02 sensor on the Kawasaki EFI engines.

B&DS stopped manufacturing the Big Dog mower. Shame.

Why should we be the one who pays the bill for all the other countries?

https://www.harborfreight.com/80-watt-iron-plastic-welding-kit-60662.html

As long as the crank shaft diamater and length are the same you can mount a larger hp engine on it.

So what engine would you consider better?

Nice looking mower clean for it's age. Hope it gives you a lot of good service.

I have a special crimping tool to put the cable end on. It is made where you put the end in kinda of a cradle and you smack the crimper with a hammer. really tight crimp.

Welcome to the forum from Tn.

Don't see any single Hondas on riding mowers they make a really good GX series horizontal engine GC engines are so so..

Have you thought about a new mower you might buy a new one for a little more.

Two things come to mind. Air bleed that is stopped up or a porosity in the body of the carb allowing it to draw more un metered fuel in to the cylinder.

What kind of superior after market gasket is better then the OEM gasket? I personally have never had an OEM gasket fail.

Yes it was a problem they also has a cam issue the compression release stop on the cam would wear off over time and make the compression rease not work. It would kick back and make an awful noise. once they fixed all that they had a counter balance problem. I have seen them break, knock the...