Search results

I took it off again and gave it a good look . I saw the magnets that lock the pulley in place when the PTO is not energized. They are working properly. I see the middle magnet pivots Thus locking the pulley in one direction.When I spin the middle piece that the bolt goes thru, That spins freely...

Hi All , First the important stuff. Model:13WK92AAK009 Serial:1C021H30256 DOM:March 2011 Well , my original drive belt to the rear wheels finally went so I had a job in front of me. The machine being 11 years old, I replaced the 3 pulleys located around the center of the machine along with...

My 2 cents. I had a Briggs with a bent crank shaft. Put the mower on its side, found the high side and hit it with a small sledge. Brought it back in close enough. I'm sure the Pros don't want to hear this but it worked for me. What did I have to lose. I continued to mow with the machine.

Craftsman GT3000 lawn tractor 917.275043 serial 012402A00129 Kohler pro 23HP CV675S Spec 75544 I was attacked by mice. They ate the some of the wiring harness attached to the intake manifold and also some of the spark plug wire. I have to piece out the wiring harness but I would like to replace...

Sears Craftsman 917.275042 Serial 012402A00129 50" mower deck. Here is my situation. I rebuilt the deck -spindles, pulleys and belts. I noticed that the flat idler pulley mounting bar has a little twist- bend to it causing the pulley to be cocked a little bit. Should the flat idler pulley...

Heated grips are not going to work. not going with a 12 v system.

Yes I want to get the 120 volt starter and I want to get the alternator for a light (maybe even hand grip heaters?) I think the alternator attaches to the outside of the recoil . I have to remove the black cap and a little rod sticks into the top of the flywheel to get the spinning motion. No...

Hi All, I have an old Snapper I 524 that was given to me. It was a wreck. I put some love into it, And now, Its a beast. I would like to go a little further with it and put electric start and an alternator on it. A couple questions: 1: Does the flywheel have a ring gear on it? 2: Does the...

Thank You for the info.

Hi All, I have a Sears Craftsman GT 3000. Model 917.275042 Serial 012402a00129 It has a Kohler Pro 23 HP CV675S Spec 75544. Bought this new in 2001. It is hard to turn over till it gets past the first compression and back fires or explodes (which ever you would like to call it) thru the...

Snakes... I work on outboard motors as a hobby. One of my motors had evidence of mice under the cowling. And a snake skin shed.

Just a thought, When I talked to the appliance repair man about what the best dishwasher was, he told me the "premier" model just had a fancier face. The mechanicals inside were the same as the cheaper model. Then he said, Just get the one you like; they're all junk.

Please tell me how you keep mice out of your equipment. This is my Simplicity SS922 . No wonder why it was surging.

you are safe at Duck Duck go

Keep your powder dry.

My Kohler was not charging. All the magnets rusted off the fly wheel.

I agree with the sledge hammer trick. Worked for me.

I use mine to trim around trees. It always clogs up even when I hold the bagger flap up with a string. I have noticed that it drinks gas too. Trimming around my house usually uses a 1/2 tank. I attribute it to the fixed jet non adjustable plastic EPA compliant carb, along with my EPA compliant...

I wouldn't want to have a "Green Machine" and have the deck rot out in 5 years. Especially if the Home owner has a lawn service to make his lawn weed free.There is only a handful of people that rinse their deck off after each use. Then I had a small engine shop not to do it because it will rinse...

I had the same problem with my with my Craftsman GTxxxx. I thought the steering link was bad so I ordered another one. Same problem. I took off the link and heated it up and bent it. I changed the geometry of it all. Now my steering left to right is about the same. The funny thing is , is I...