Search results

Glad you are not being picky. Are you going to frame it or use it?

Try a properly gapped New Spark Plug. I believe you have a fuel delivery problem if it runs for 15 minutes. Try starting with Fuel Tank Cap removed, then replaced. New filter installed at correct orientation. Remove float bowl, clean and inspect. Fuel should flow freely when bowl is removed...

Keep it simple. Get a bicycle drink holder and bolt it to the handle. Keep Quick Start in it. Done. :cool:

From Photo #2 it appears that the key is not IN the Keyway, binding the Wheel, Try to put the key back in its' place. Perhaps the key has sheared off or the wheel has become loose on the shaft or both. Spray into the keyway from both sides with penetrant and let sit for a couple days Use...

Replies are not showing for me.

My X-320 JD has a 48" deck, 22 HP. No mulch attachment. A completely different method of attaching the deck. It mows very level over uneven ground. It is properly leveled, at correct tire pressure. Lower at the front. I mow clippings into unmowed area and clean up what's left with a wide...

Please state what you have Done to try and get it to start. Remove and clean all battery connections, including solenoid and ground and starter post? Use a known good fully charged Battery.? Do NOT use a jumper from a vehicle with the engine running. Fresh Fuel, new Filter? Adequate Oil?

I forget the problem now.... Oh Ya. Wipe it down as much as possible and leave it running to try and determine where the oil is coming from. Gasket or Seal. Some cardboard underneath the suspect area may help after it is turned off.

Indeed Holmes.

Try removing the filter, and with an air source blow back towards the tank. Remove Tank Cap FIRST. Don't stand over the tank. Install new clear plastic covered filter in the correct direction. Clamp fuel line and remove Float Bowl. Inspect for debris and clean. With float bowl off carb...

If the PTO bogs it down perhaps you have a spindle or other bearing seizing up? Loosen Deck Belt and make sure all blades turn freely. A lean condition may cause backfire.

Yes, you can get rutting on slopes, mostly from wheel spin while turning. Measure the Narrowest Gate you have. Subtract 2" Go to your dealers and ask about Riding Lawn Tractors. Lift up the Grass Chute and measure across the deck noting clearance. Then get the appropriate size deck. A JD...

Speak to them in a friendly manner first. If that does not work place a line of rocks along what you KNOW to be the Property line, or a long row of narrow patio stones on YOUR side of the line. It may be dimensioned on the deed to your property. If not, have it surveyed. Fences make good...

I believe we are talking about the Valve SPRING Cap? How is the valve spring kept in without a cap? Usually held in place with 2 tapered wedges (keepers). If the engine still runs OK, put several strong magnets on the bottom of the engine. Epoxy them in place. If there is Ferrous debris in...

Too high!

I was thinking bent Crank or Covid! Glad you lucked out.

Excellent advice. A NEW anchor plate should be attached first. Present one has cracks and is distorted. If you have clearance, get a 1/8" plate cut, formed and drilled to cover the existing plate and seal well it all around the perimiter.

Never charge a small battery off a running vehicle. Stator will burn up It would be helpful if those asking for help would give all info. Does the starter Turn but not engage? Does the solenoid 'click'?Did you check and clean battery, solenoid and Starter motor terminals?

You cannot educate the Stupid. Clever marketing ploy. Burn up the engine. Throw it all away. Buy buy buy. I warm up my ICE's every Spring and Change oil and filters. Synthetic in the Snowblower for easy starting.

Try straightening it, then when it is close SELL IT. Not worth the repair effort or cost.

Simply drain tank and system, run the engine til it stops, use Float Bowl drain if there is one. Use Premium non Ethanol fuel if you can find it. Taryl tested a variety of 'stabilizers'. Check his video on that.

Set the valves @ TDC, ignoring the ACR. Set them cold. 0.004-6" . It does sound like a fuel problem. Check needle and seat for operation and flow. Check (remove and clean) ALL Battery cable/solenoid/starter connections. File Battery posts 'bright'.

Check the Starter with a known good battery. + cable to starter terminal, - cable to Starter bolt. If starter engages, work backwards to battery. There is an 8-10 volt connector near the Ignition switch. Unplug it, spray with Battery Terminal cleaner then Brakcleen and reconnect.

It is obvious it is starving for fuel. Change the filter, blow back line to tank with cap loosened. Turn ON valve if there is one. Remove float bowl and lift float. If no fuel comes out you have a plugged needle and seat. RE and RE.

Exactly Been there on both.

Blade bolts do not self tighten. If you have difficulty you are tightening them too tight to begin with and fail to clean and lubricate the threads. A simple box end or 8" ratchet will tighten them sufficiently. Small couplers do not lower the Pressure, they lower the Volume.

I believe you have a fuel starvation problem that may be cured by removing float bowl and carefully pulling out the pin that holds the float. The needle will come down with it. Open fuel valve and you should get good continuous flow. Reinstall and try it. If it begins to slow down after...

If you have a nearby metal fab shop that does welding, speak to the owner and see if he can do a small custom job. Grind all paint off near the crack Drill a 1/8" hole at the end of the crack and V groove crack slightly. Have them weld both sides and grind the bottom side flush.

You might check that Float/needle is not stuck . Replace the spark plug just in case.

Take your Med's.

Popping sound may indicate Lean fuel mixture or timing.

Try draining a bit of oil from the bottom ot the tank and let it sit for a day. Water if present will sink to bottom. Change Filter. Don't over think this. It is unlikely that there is much if any water in the oil unless done on purpose.

Check to see if carb has fuel after sitting for a few days. Replace Filter if there is one and spark plug. Try pressing primer bulb if equipped only 2 times. Sounds like you may be flooding it. Report.

Seems strange to remove the + battery connection instead of the - one

Try it with the Fuel Tank Cap loosened. If it still won't run past 30 sec, Blow fuel line back into tank with cap loose from carb. Replace Filter if there is one. New ones can be plugged.

Well Said!

RTFM

Perhaps you are turning the same way every time with low air pressure. Stay with the solid tires and put a cushion on the seat.

Follow the wires leading around the base of the engine if it is like the Cub Cadet zero turns. A light blue wire may be broken or shorted. Charge the Battery fully, off the machine and take it to a shop for Battery Load Test

I would suggest Green. Local Sod Farmers would be one of your best info guys, compare with Nursery advice. The wind will quickly contaminate 'pure' strains. Work up the surface first, spread twice as much as recommended as only 40% germinates. Lots of water, daily.

Get some carb cleaner and carefully wipe off the Viton tip of the needle. It does not require a Viton 'seat'. Clean the bore where the needle goes. Looks like Ethanol contamination to me. Set float as described above. When you turn the key Off/On there should be an audible 'click'. Hold your...

It is clear to me that some 3" wide by required length of 1/16" thick Aluminum could be pop riveted over that. Keep rivets clear of belt path and raise it or lower it so the belt does not touch anything. You're welcome.

If it runs for a few seconds, I would suspect fuel starvation. Disconnect line at pump/filter and after removing the cap blow backwards thru the fuel line. Do not stand near the fuel tank! See if the Float bowl is filling.

NASCAR is hardly NASCAR anymore. Too many rules, regulation and of late Change. Half time at LA was pathetic. NASCAR is not about Rap 'music'. I doubt we will live to see (I hope not) V6 or Electric but who knows? They now call a Driveshaft a Propeller shaft! This new generation of cars has a...

I suggest you cut your lawn a bit higher perhaps an inch and then use a Brinley sweeper. It would be difficult to improve on the Manufacturers design in a blade.

High (?) Octane fuel does NOT burn Hotter, I burns Slower to avoid predetonation. Use it.

Time to Repower I think. Do a compression check and remove cover and check Valve assembly.

I expect most decks are Powder Coated with no primer or proper surface preparation. The stamped deck and welded attachments need to be Sandblasted to SP6, then using an inorganic zinc primer and Hi-build epoxy topcoat done to manufacturers recommendations, you will have a durable coating. I...

Not worth tearing down the engine. It should start with rope first pull. Be sure you have fresh fuel and don't flood it. Electric Starters are over $300 Cdn. Check with Donyboy.

Starting Fluid first, with Choke OFF.