Search results

Around here, I'd list for $90, then back off to $80. Back further down if no serious bites.

Briggs model #? Stamped in a valve cover or shroud.

I really liked Season 1 but Mrs Norris is quite irritating. Sling Blade is a classic.

Well....30 gb is minimum for OS & programs that I want. Debian WILL install w/ only 1 gb free space. You could have a dual boot system - choose Windoze or Linux from boot loader. I've had errors with that and don't trust it for important stuff. Is this a laptop w/ only 1 HDD slot?

30 gb minimum Hard Disk Drive space for Operating System. I put the OS on it's own Solid State Drive - much faster than older platter-wand mechanical HDDs. Installation USB stick - probably fit on 1 gb stick. 120gb SSDs are ~$15 these days.

I'm trying a new to me Linux - Debian 12.8 w/ XFCE. Faster & more stable than Ubuntu 24.04.1 (Ubuntu is based on Debian). The distro might not have all the pkgs you need but fairly easy to find/install. Eg: I had to add 2 pkgs to mount my Moto Edge phone for file transfer.

Glad to hear it's going fairly smoothly!

I switched to Linux years ago. Tried 10 different distros. Top of list = Linux Lite 6.0, Mint 21.3, Xubuntu 24.04. All 3 are Ubuntu based and easy to transition from Windows. So, it really boils down to what "desktop" (GUI) you prefer. I like XFCE of Xubuntu - an official flavor of Ubuntu w/ 3...

What country are you? The manual for what country? USA 87 octane (R+M/2) would be 90.5 Octane (RON) in Europe.

You need engine model#. Will be on valve cover or engine block near spark plug. Eg: 126M02-1015-F1

Search that model # & find: MTD 753-06190 Carburetor.

What's the model #? If the fuel pump or metering diaphragm are stiff, they need replacement or get new carb. If you are referring to the Hi-Low jets, Low is always closest to the cylinder. Try 1/2 turn CCW.

Is trimmer Model #CMXGTAMDSS30? Lowes sells them. Go see a new one & check the fuel line routing. One port is is probably a breather of some sort.

Did you pull the drum/sprocket & look for obstruction between it & band? The spring looks elongated = some pressure in disengaged position. A new spring is cheap. Homelite 985240001 See how parts go together...

I do like real sports events = the clock or measuring tape or # of hits determines winner. Thankfully, no break dancing in 2028.

I think you're describing compression release. On most LT/GT and bigger engines, the camshaft has an arm that bumps the valve at low RPMs. This allows the crankshaft to spin faster & start/run. Cam arm slings out of the way at higher RPMs for full compression.

Agree re: plug out & grounded. Try another plug, too.

How do you set the coil air gap? I use a business card between the coil legs & magnets. Can you do a visual check on the timing? Flywheel key has sheared - can be just a tiny bit. No other answers - pull FW to check well. You have fuel/air, compression & spark - gotta think timing.

North AL. In a whole week, we've been above freezing for 8h. We don't insulate for that. 3 streets over - a water main busted. Quite a geyser for 20 mins.

North AL. Today we're supposed to go above freezing for 1st time in 5 days. I bet this is a once in 50 years event for here. Normally snows 2-8", warms up and can drive safely in 2 days. Star, may get more freezing rain, coming from Memphis.

North AL at TN line. We had more sleet than snow. Roads are sheets of ice. 13*F now and 2*F tonight. Local TV drives around filming, saying "We haven't seen any road crews". LOL. Star, did you get more snow or sleet?

An easy way...business card on FW magnets. Loosen 2 coil screws. Let coil legs slam onto magnets. Tighten screws. Check that FW doesn't hit legs on rope pull.

Remove spark plug. Rotate crankshaft till piston is coming up. Stuff some rope on top of piston. Unscrew clutch CW.

If weight not increased - great. I have 2x FS55 and run them hard. They just scream.

It may run factory new if carb & fuel lines are good....for a while. Then you use it with an engine tilt and oil slinger/dipper doesn't splash oil. P, R & C are oil starved and start scoring - compression drops. I'm just a hobby mechanic but I've learned to steer clear of tiny MTD 4 strokes...

Hammer is saying read this: https://www.lawnmowerforum.com/threads/engine-oil-for-honda-hrn-216-vka-push-mower.70083/ Naw, don't spend extra.

Get well soon, StarTech!

Small barrel carbs. I had one that the rotating barrel was worn and let too much fuel thru. Do you have a Throttle screw on carb? (I don't recall one). I had to get new carb.

Hopefully somebody who's worked on one will chime in.

Sounds like the clutch for reel cutters is stuck engaged. Does clutch handle operate properly? Does wire inside cable housing move back & forth? Take pics of where the clutch cable enters clutch near cutters.

What is always spinning - drive rollers or reel cutters?

Check in here: https://oldlawnmowerclub.co.uk/sites/default/files/opmanual/Atco%20Commodore%20B14-B17-B20.pdf

bertsmobile1 wrote this in: # 15 https://www.lawnmowerforum.com/threads/brigs-mower-will-only-start-with-starting-fluid.38149/page-2 remove the carb and with a spray can of carb cleaner , WD 40 or similar that has a long nozel on the trigger, spray fluid backwards down the carb through all...

Choke butterfly fully closing? Was cleaning - disassembly and passages open? 2 carb bolt holes open?

Engine model #? 12xxxx-?

~10 years ago, when I had these internal parts failures - it was $140 in parts.

Is this your unit? https://www.ereplacementparts.com/homelite-ut08544-vac-attack-parts-c-18807_18808_139650.html They don't part lower than a short block and then say it's NLA. These are really cheap engines and will have some slop. Think a C clip beside con rod would grenade engine if slung...

Look at camshaft 46 in IPL. 2 teardrop lobes push rods for valves. The cam gear mates with crank gear. Cam gear could have jumped time. Also, 43 Oil slinger/gov can blow up. Can't tell from IPL but cams can have a boomerang compression release - spring loaded and clears away at run RPMs. It can...

Landline telephone wire works well for carb holes. But if you can't put fuel in plug hole, re-insert plug, pull rope a few times (maybe 10x if floody), and get a 2 sec run....it's not an air-fuel problem. Think compression or spark/timing problem. See if valves work.

Engine model #? Years ago, I had a 12S912 on a pressure washer. IIRC, it was gov/oil slinger failure with camshaft damage. Pull the valve cover and see if valves operate properly. Do both valves close as piston approaches TDC on compression stroke? Also, did you wire the the carb jets/orifices...

Internal carb passages are probably partially clogged with varnish or debris. Esp if you use ethanol gas. Need total carb cleaning - disassembly & parts washer. Inspect needle & seat. Carb is Tec 640330. Probably NLA. You can search for an AfterMarket replacement and match it. Why change the...

Measure your HxWxD. 3.54 x 2.76 x 3.98 inches is a standard size. Search online for 12v SLA battery (3 or more Ah). You'll need to cut your old connector off & attach to new terminals.

Engine spins Clockwise from top view (think about pull rope). Did engine stop suddenly as hitting an object? Could be flywheel spun - check key alignment. Have you tried carb spray/pblaster in carb throat or plug hole to see if it burps and 2 sec run? If so, may be debris in bowl, bolt holes or...

Example: this probably only needs bowl cleaned & bowl bolt wired out.

Most (maybe all) Briggs 12 mower engines will bolt to your deck w/ 3 bolts. The differences will be Autochoke vs primer bulb & others. Some older engines will have a throttle cable to the handle (avoid). Study your IPL 121S02-0130-F1 and compare to potential swap IPLs. I have 126M05, 126T02...

$950 is ridiculous for a push mower engine. Around here, you can find mowers w/ a Briggs 12xxxx engine for $20-$60 that just need a carb cleaning/rebuild or a new carb. I like those engines - have them on multiple mowers.

It may be this transaxle: Read the Peerless blogspot https://www.lawnmowerforum.com/threads/peerless-205-024c-hydrostatic-transaxle-sluggish.75263/#post-477328

See if you find your mower here: https://www.partstree.com/brands/yard-king/walk-behind-mowers/

My Deere lower cute is 7.25" OD.

Engine model #? Eg: Briggs 126T02 1223 F1. Tip over oil dump needs 45-60* incline...did you go that far?