Search results

Thanks for the information. Stock seal is 42mm x 52mm x 7mm. I have ordered one with 40mm ID. Will advise after installed.

This is turning into a head scratcher. I replaced sump/sleave and new seal. I filled it with oil and let it set all day and never leaked a drop. I started and let idle a minute and started leaking oil again from seal. I removed dipstick thinking crankcase pressure may be forcing oil out...

I've had the sump off and sleeve looked in correct position. I have ordered a new sump/sleeve, seal and gasket. Will update once installed. Thanks for all information.

I just pulled breather and it's clean

Thanks. The sump comes with a sleeve instead of roller bearing and if I'm reading right, it's all one unit. I'm wondering if the sleeve wallows out, would that cause leak at seal? 0C57320SRV

I have a 2008 Dixie Chopper with a GTV990 engine that one day just started leaking quite a lot of oil from crank seal on bottom side where pulley is attached. I replaced seal twice and each time placed it at a different level in case there was wear on the shaft but still leaks. Just wondering...

Success !!!! Made a call to Generac who put me in touch with Dixie Chopper. A tech there told me that their Generac engines used only half moon woodruff keys not off set. I replaced key with item number recommended in parts catalog (G082774) and it started instantly. Thanks to everyone for...

1. I was getting spark, fuel, and compression. Thought timing issue. 2. New Champion from Rock Auto that is done every spring. 3. Yes. Mower was moved to garage and no sign that their was any water intrusion from storm. 4. No timing light 5. Not sure of cylinder condition, but will use...

I've got key ordered. Part number I found was 082774 (4x19D) Thanks to all for help. I will advise outcome.

Plugs are new. No changes to mower since last time it was used. We did have a severe rain storm before it quit running and even though stored in barn it probably got wet.

2008 L.P. 3000 with a GTV760 Generac engine

Just pulled flywheel and found some shavings around crankshaft seal. This key looks suspicious. Would that be enough to effect timing and cause a no start?

Put small amount of 2 cycle mix gasoline in one of the cylinders and nothing. Wondering if I sheered a flywheel key.

I own a 2010 propane and it's been a great mower. Went to mow yesterday and it tried to fire a couple of times and now it won't at all. It's getting spark and I smell gas but nothing. It doesn't seem to turn over as fast as it should so I tried different battery with same results. Any help...

Turns out I didn't do my homework. Sensors and gauges ohm ranges have to match and I didn't research that. Thanks for responses

I replaced my sensor with an aftermarket one. The gauge works because when I ground the signal wire, it shows full. The new unit will only make the gauge show 1/2 even though the float is moved to the full position. I have included three pics, with the float rod in the empty, 1/2, and full...

Thanks for that info Star Tech. I've never worked with a shorting connector. Are they a safety cut off if seat plug becomes detached?

Found problem. Connector from harness to seat switch has plug wrapped in a piece of wire that when pushed all way in connector rides on plastic creating open circuit that mower wants to run. It had backed out causing brown and white wire to connect thus sending path to ground. Owner had...

Update: I think I may have found the issue. I've disconnected every switch in the system. Neutral switch (left and right), E brake switch, PTO, Ignition, connection to engine, seat switch, and I'm finding I have a short to ground on white wire circuit only. Is there a way to run this down...

Thanks for replies. Tried both ways with seat switch, no difference.

I just bypassed seat switch, checked safety switches for steering arms and parking brake, and all are working as they should. Also checked continuity on whole mower using schematic with positive results. Noticed the starter relay was tied into safety switches and tested it also with...

Ferris IS 700Z. Got done mowing and turned off to use compressor to blow grass off machine. Got back on started it and now whenever any control is moved (steering handles, parking brake, pto), engine shuts off.

I have a 2007 Dixie with a Generac engine that I think is a 27 horse powered by propane. Tags identifying engine are gone and unable to find much info on line about specs. Any help would be appreciated to adjust valves.

I'm working on neighbors Lawn Boy model 10605 because self propelled system quit working. Belt tension is good and and gear box will grab and turn wheels a couple of times and quit. I'm fairly confident gear box/axle need replaced, however, I found something about a recall (attached) on the...

will do.. thanks for reply

I have a Craftsman chipper/shredder with a Briggs 8hp that seems to be running way too fast. Is there a way to adjust the rpm's?

I'm working on this tiller for a neighbor (true story). The machine is really in good shape except for the tank. I can't believe part has gone missing. There's one on bBay that's in the bidding process. I'll check with owner and see if he would rather go new if you still have that one in...

Thanks for reply slomo. I have a call in to a local shop where I've bought used parts before.

Full of rust. I think that can be resolved, however, the secondary sump chamber is paper thin and rusted through.

Thanks Scrubcadet10.

It ain't the space shuttle "Classic"

Help me "Oh Wise Ones". I'm trying to replace gas tank on a Craftsman tiller model 917.295553. Engine is 5hp B&S model 13502-0237-01. Showing tank part number 495391 or 694315 is discontinued. Is there another alternative?

Ok, thanks to all.. I'll contact seller about a return/replacement....

Thanks for reply Star Tech. Everything I'm looking at says part number 590454 for that model number. Am I doing something wrong?

I recently ordered and received a replacement coil but the mounting holes won't match up to engine. Is it advisable to drill mounting holes on coil to accommodate? B/S model: 12H802-2682-B1 Part received: Ignition Coil fits Briggs Stratton 491760 492416 493237 590454 692605 695711

Thanks guys... That helps a bunch

I have a self propelled mower (model 12AE46JA009) with a 173CC OHV engine that will start ok but it takes about 30 seconds to rev to full operating rpms. After it's warm, it will start and operate normally. Any ideas what might be causing this?

Hello, Can anyone tell me the part number I need to replace the cable that operates the transmission for this mower. I'm having trouble making determination from the J.D. website. Thanks

Dumb question..... What size replacement string is used on a FS120 trimmer?

I'm working on a chainsaw UT 10883, and am in need of the following part. Homelite 04933A Washer, Cupped It shows as obsolete and wondering if anyone might know a substitute?

I sprung a leak today and am wondering if the hose is high or low pressure. It's about 16 inches long with female fittings on both ends. Is this a dealer part or will something else work?

Can anyone give me some guidance as to why recently purchased golf cart will only run without any of the air cleaner parts hooked to carb? It runs great with nothing attached to that side of carb, but any type of obstruction, even just the hose, will cause it to load up and flood to a stop...

I have a BS Intek 344cc 12.5hp (219907 0131 B1) that was allowing gas past the carb to the sump. I attempted to get the needle to seat with no luck so I purchased an aftermarket carb. After installation, engine surged and backfired, which it didn't do with original carb. I removed float...

I just got done working on a neighbors Wheelhorse 857 and ran a test cut on yard. It acts like the blades are tearing not cutting the grass. I double checked installation of both blades and they are sharp enough to shave with. When deck is engaged, turning the blades by hand will cause the...

A little help please.... It has spark, fuel, and valves have been lapped and lash set. It won't even pop. I do notice compression is 25psi. Could that be from piston rings? Update: When assembling carb, the insulator (16073-6001) that goes between head and carb had a rubber plug. It looks...

I am replacing handle on walk behind mower model JA62 GXJA62V220658. Part numbers are M120194 and M110957. The replacement parts are making total length of handle shorter than original was, and now the push/pull cable (AM115556) is too long. Is it possible that the length of that cable has...

A little help please. I have a Courage 20hp model SV601 that will run fine for about 30 seconds and then starts to get rough, backfires and dies. If it sets long enough for fuel to fill bowl (5-10 seconds), it will fire and again and repeat. I have gone through carb twice, new fuel filter...

I own a Mantis cultivator model SV-2AE and trying to find a replacement coil part number 15660109820 which is showing no longer available. Is there anything that will replace it? It sets on bottom of cultivator separate from the flywheel and coil exciter.

I have a 5hp Tecumseh LEV115 that rips pull cord from hand when it is pulled to start. With spark plug removed, it pulls smoothly. I have checked to make sure key at flywheel isn't sheered. The intake valve guide is extremely worn and wondering if that might be causing it to kick back...

I just purchased a Swisher walk behind trimmer and unable to locate any parts using the model number. In fact, I'm unable to find model number anywhere on net? I'm looking for transmission cable. Help please. Model WB 522 Serial L2 99 033081