Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Oddjob's latest activity
O
Oddjob
replied to the thread
HRX 217
.
Sounds like you are burning a little oil. If it quickly burns off after start-up and runs strong, I wouldn’t worry about it. It’s...
Sunday at 9:49 PM
O
Oddjob
replied to the thread
Snapper RP217018BVE Walk Behind Mower
.
Yes, straight 30w oil should be fine. I googled your model number and found lots of places selling parts for it. Your belt is snapper...
Sunday at 9:32 PM
O
Oddjob
replied to the thread
Starts fine, idles well, bogs down when turning on PTO.
.
So now swap sparkplugs and see if the good cylinder has switched sides. If so, you have a bad plug. If not, most likely a bad coil.
Sunday at 8:52 PM
O
Oddjob
replied to the thread
Starts fine, idles well, bogs down when turning on PTO.
.
One way to tell if you have only one cylinder working is to start it up and spray water on the mufflers. If you have a failing coil...
Saturday at 9:59 AM
O
Oddjob
reacted to
Tiger Small Engine's post
in the thread
Storing a mower with no gas
with
Like
.
You stored it without any gas, but did you run the fuel completely out of the carburetor as you stored it?
Saturday at 7:25 AM
O
Oddjob
replied to the thread
Brand New HRN216VKAA hard to pull recoil starter rope
.
Whether covered by the recall or not, this mower is not working as it was designed to do. It is brand new so presumably still under the...
Aug 16, 2025
O
Oddjob
replied to the thread
MTD deck height
.
This is why I read this forum. Thank you, ILENGINE. I have run into this on older riding mowers and could never figure out why I...
Aug 16, 2025
O
Oddjob
reacted to
Auto Doc's's post
in the thread
Backfiring through the exhaust
with
Like
.
Hello PTmowermec, Even though you disconnected the coil kill wires, the anti-backfire still has the ability to shut off the fuel in the...
Aug 16, 2025
O
Oddjob
reacted to
platefire's post
in the thread
Howdy from Maine, USA
with
Like
.
Welcome from Lousyana. We'll treat you so many ways, you bound to like one of them:>) I don't think of myself as old but when I look in...
Aug 9, 2025
O
Oddjob
replied to the thread
And if I'm not strong enough to tip it over?
.
I’m old (73) but still have enough strength to put my RER Snapper on its butt. It helps that the heavy part is all in the rear and you...
Aug 2, 2025
O
Oddjob
reacted to
Rivets's post
in the thread
Stihl MS 250 Chain Saw Problems
with
Like
.
Before bad mouthing anything, take it back and have the mechanic take a look at it. At a good repair shop and in a reasonable time...
Jul 26, 2025
O
Oddjob
replied to the thread
Rear drive wheel-Toro model 20374- keeps coming loose?
.
Does your machine have a wave washer on the wheel assembly? If so, maybe it has lost some of its liveliness. You could try bending it a...
Jul 19, 2025
O
Oddjob
replied to the thread
Rear Engine Mowers
.
I have a 1984 model 28” Snapper RER with the bicycle handlebars. It has its original B&S flathead 8hp engine. My yard is hilly but I...
Jul 19, 2025
O
Oddjob
reacted to
hlw49's post
in the thread
Rear Engine Mowers
with
Like
.
Does Snapper make their RER mower anymore. It is bullet proof. Forest Gump mower LOL I still have one but don't use it. I had one that...
Jul 19, 2025
O
Oddjob
reacted to
cmayo's post
in the thread
Kohler Courage 20HP SV601 - Overspeed, no throttle control
with
Like
.
Yeah, I had just started to Google "throttle plate" instead of "butterfly valve" and am seeing more hits for shaft-and-plate kits...
Jul 5, 2025
Top