Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
New posts
New media
New media comments
New profile posts
Latest activity
Menu
Log in
Register
New
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Latest activity
G
Gord Baker
replied to the thread
How to stop cut grass blades from accumulating inside mower cavity?
.
Sell the E mower.
Jul 12, 2025
G
Gord Baker
reacted to
Back44L&G's post
in the thread
M-ZT 52 Stops running when hot!
with
Like
.
I just went through that last week. I cleaned the carburetor, emptied and cleaned the tank. I removed the ignition module and cleaned...
Jul 12, 2025
G
Gord Baker
replied to the thread
M-ZT 52 Stops running when hot!
.
Remove Fuel tank Cap and fuel line at filter. Blow back the line carefully with minimum pressure. Do this outside, off the driveway...
Jul 12, 2025
G
g-man57
reacted to
Auto Doc's's post
in the thread
Rear Engine Mowers
with
Like
.
Hello Packman88, This site does get clunky and lags at times, so be aware of that.... I own a 1988 Snapper RER with a 30-inch cut and...
Jul 12, 2025
G
g-man57
reacted to
hlw49's post
in the thread
Rear Engine Mowers
with
Like
.
Does Snapper make their RER mower anymore. It is bullet proof. Forest Gump mower LOL I still have one but don't use it. I had one that...
Jul 12, 2025
G
g-man57
reacted to
ILENGINE's post
in the thread
Rear Engine Mowers
with
Like
.
Snapper has been licensed by Briggs to DAYE. If I remember correctly production of the RER was ended a few years back.
Jul 12, 2025
J
JimP2014
replied to the thread
Engine shakes while engaging blades
.
But one thing I did notice is that the last time I replaced the cylinder head gasket was about one year ago. So the question is one year...
Jul 12, 2025
F
Forest#2
reacted to
StarTech's post
in the thread
Help with parasitic
with
Like
.
A couple options here. 1> Disconnect the fully charged battery and check in three weeks. 2> or better disconnect the battery install...
Jul 12, 2025
J
JimP2014
replied to the thread
Engine shakes while engaging blades
.
I mean with the cylinder head off alrready.
Jul 12, 2025
J
JimP2014
replied to the thread
Engine shakes while engaging blades
.
Thank you for this additional information I can tell you that when I was looking at the engine block on the lower right there was a...
Jul 12, 2025
R
Rivets
replied to the thread
honda gc160 runs at full speed
.
This service manual will explain how to adjust the governor...
Jul 12, 2025
M
mechanic mark
reacted to
Rivets's post
in the thread
M-ZT 52 Stops running when hot!
with
Like
.
Get yourself an inline spark tester and the next time it happens install the tester and check for spark. I suspect you will find no...
Jul 12, 2025
R
Rivets
replied to the thread
How to stop cut grass blades from accumulating inside mower cavity?
.
Check your RPMs, if it is running below 3400, adjust. Running below the clippings will not be cut or thrown out properly.
Jul 12, 2025
B
Back44L&G
replied to the thread
M-ZT 52 Stops running when hot!
.
I just went through that last week. I cleaned the carburetor, emptied and cleaned the tank. I removed the ignition module and cleaned...
Jul 12, 2025
L
Laabk2
reacted to
ILENGINE's post
in the thread
What is the Purpose of Each of These Items?
with
Like
.
Actually the small wire ring is suppose to slip over the fuel line install the fuel filter and then slip the wire ring down over the...
Jul 12, 2025
New
Top