Export thread

2022 model - 17RIEACL010 - has maybe 200 hours or less on it. Was mowing and it just quit. Won't start now. Replaced plugs, gas is new and fresh, made sure carb and associated parts were clean. The mower will start (with choke pulled) and run... as long as I keep the switch turned to the start mode. When I release it to run, the mower stops. Dealer is backed up, as well as local shops. What I knew about mowers... I lost after my second brain surgery in September 2022. I hope someone can help. Thanks in advance.

Quit like you turned it off or quit like it was running out of fuel ?

Sorry for the delay in replying. My dizziness really hit me this weekend.

My son in law was mowing. He said it just quit, like he had turned it off while mowing. Has plenty of fresh fuel. It just won't run unless I keep holding the starter switch to star. Thanks for the reply.

I can not find wiring diagram for your mower using the numbers provided
Could you please take a photo of the ID tag and post it ?
Sounds like a seat switch or module fault
The seat switch is ( generally ) not in the starting circuit but is in the run circuit
This allows techs like me to start the mower with no one in the seat to service the mower but prevents you getting off with the engine running & brake off or stops it if you fall off .
Could also be a bad brake switch and / or there may be a relay but I will not know till I can look at a wiring diagram
For the purpose of diagnosis you can remove the blower cover then pull the kill wires off the magneto coils
If it is a safety switch problem then the engine should start & run as normal
down side is it will not turn off if the carb solenoid is not working and you can drive away with the parking brake on which destroys the brakes .

Will, hopefully, do it tomorrow. Have a funeral to attend tomorrow. Seems like that's all I do now, go to old friend's funerals. I'll be 73 on Saturday. As an undertaker's son... I've been to a LOT of funerals. Losing so many old friends. HUG your loved ones EVERY chance you get.

Is this what you need? Thanks. Just realized it's still under warranty. If I can't figure it out, I'll try to borrow a friend's trailer and take it to them. Problem is loading it without it running. Thanks!!!

Thank you
The second photo is exactly what I needed but unfortunately I still can not get past MTD's first page so the web page must be geo locked
Cub Australia does not recognise any of the numbers so I will have to leave this to USA members

Would it be legal for me to copy and post what you need on this page? If so, just let me know and I'll look for them. BTW, I've had a few university students from Australia. One of them was Adrienne Beames who was a student at Texas A&M back in the mid-70's. I tried to run with her... BAD mistake. She practiced LSD - Long Slow Distance back then. After about 5 miles... I turned around and came back.

Wellif you have a wiring diagram please post it and we will walk you through it
All I can find is an electrical parts list which simply shows the loom plus the bits that do not come with the loom .

And because of the way world maps are drawn OZ looks to be small
It is roughly the same size as continential USA with a population & economy roughly equivalent to California

It's getting late here, but I'll try to find it. Thanks.

I can't find the right one... internet seems to show me ALL of the diagrams... except what I need. I will look at the manual tomorrow and see if I can find it. Thanks.

The last time some one was here looking for a ZT ! wiring diagrams was this thread
ZT 1 wiring diagram
Which as you will see was never actually closed

It’s under warranty, so I just took it to them today. Tech thinks it’s in the switch. I’ll post when I get it back… may be 2 weeks.

Badknee_1 said:

It’s under warranty, so I just took it to them today. Tech thinks it’s in the switch. I’ll post when I get it back… may be 2 weeks.

Click to expand...

I think your tech may be right. I had a similar problem with my jd425, switch was worn and not making contact when in the run position.

OK... sorry for the delay in replying. Brain surgery last September really messed up my mind.
It was the starter switch. Dealer kept it for nearly 2 weeks because they were so busy. Tech told me it didn't take but about 15 minutes, at most, to fix it. He apologized that he couldn't get to it quicker. Thanks for everyone's help. Even though I'm "fixed" now... I'll pay the fee or membership or whatever I got a note about. THANKS to everyone who tried to help me. Take care.