Export thread

I would like to have a picture/drawing of the throttle linkage assy. to this carb.

I may want to purchase a new /rebuilt carb.

Any help would be great. I have owned it for 2weeks now!

If you haven't taken it off yet, take a photo.. or draw it down on paper.

EngineMan said:

If you haven't taken it off yet, take a photo.. or draw it down on paper.

Click to expand...

Will do. I'll have to find out how to post a picture.

EngineMan said:

If you haven't taken it off yet, take a photo.. or draw it down on paper.

Click to expand...

pictures (3) sent to you.
Thank you for the picture. I will need the linkage as the one i have is not like that.

Your photo is showing the throttle/governor link and you should have a spring for it to, has your engine got a air vane governor because you say that the photo that posted up is not like yours so therefore its not mechanical.
You should be able to work it out now by the pic that I have posted.
If you need more info then this, then we need more info from you, like engine/type numbers.

Your # 30 looks similar. I took some more pic. The one shows what I think is the correct setup using a paperclip for reference.

I need help with the serial/type motor plate location. Is it by the spark plug?
Thank you so much for your time.

It looks like I will be parting out my YTV/16 as the motor is broken! The 656cc twin 16hp
has a broken rod

LB

The loop end (pig tail) is where the spring go's on to, if you look at your No 1 photo you will the spring on it.
other link go's between (A) and (B)

No help. I can't find the numbers. The pictures will not open.

EngineMan said:

The loop end of the link go's on (B Governor arm) and the spring also go's into (onto) the loop.

Click to expand...

I'll move them over to the throttle. Is there a part that would go were the spring was mounted now?
Do I only need the wire (see pic) and spring?

silver1 said:

I'll move them over to the throttle. Is there a part that would go were the spring was mounted now?
Do I only need the wire (see pic) and spring?

Click to expand...

How am I ever to find the missing wire from the governor to throttle?

I found the type & serial number for Tecumseh 10hp.
Had to use a mirror to read the numbers.

143-296042 sn= 9045D

A VM-100-157018A maybe?

Part numbers are......

Link Throttle 33860
Link Governor spring 33151
Spring Governor Spec, No 40933k part number 33578

Part numbers are from www.mymowerparts.com 606-678-9623 or 606-561-4983 and are for the VM100-157018A

But remember, Tecumseh went tit's up sometime ago now, so some parts may not be available.

I'll check it out. thanks.

EngineMan said:

Part numbers are......

Link Throttle 33860
Link Governor spring 33151
Spring Governor Spec, No 40933k part number 33578

Part numbers are from K&T Parts House Lawn Mower Parts & Chain Saw & Trimmer Parts 606-678-9623 or 606-561-4983 and are for the VM100-157018A

But remember, Tecumseh went tit's up sometime ago now, so some parts may not be available.

Click to expand...

I called today and they do not have any of the parts. I'll need to find a broken motor.
thanks for your help. LB

I googled the Tecumseh 10 Hp VM100 and found a site in Texas and ordered the parts.
I hope the really have them in stock. I should know later today.
Now on to the throttle cable I need.
LB

Re: tecumseh 10hp Sears LT 10 carb. and linkage......Done 11/22/12

EngineMan said:

Part numbers are......

Link Throttle 33860
Link Governor spring 33151
Spring Governor Spec, No 40933k part number 33578

Part numbers are from K&T Parts House Lawn Mower Parts & Chain Saw & Trimmer Parts 606-678-9623 or 606-561-4983 and are for the VM100-157018A

But remember, Tecumseh went tit's up sometime ago now, so some parts may not be available.

Click to expand...

Well I have to thanks all for the info.. A special thanks to Partstree.com for all the Tecumseh throttle linkage to make this unit complete. (see Pic's)
LB

EngineMan said:

The loop end (pig tail) is where the spring go's on to, if you look at your No 1 photo you will the spring on it.
other link go's between (A) and (B)

Click to expand...

Hey i saw these images and some reason i cant find where the 2 fuel lines go can you give me an image of the fuel line that comes from the gas tank to the carb thanks.

real8deal said:

Hey i saw these images and some reason i cant find where the 2 fuel lines go can you give me an image of the fuel line that comes from the gas tank to the carb thanks.

Click to expand...

Two fuel lines? On the 10 Hp. Tecumseh with the tank mounted to the engine, the fuel line comes out the bottom of the tank, and if there is no fuel filter, goes to the Carb. on the back side.

silver1 said:

Two fuel lines? On the 10 Hp. Tecumseh with the tank mounted to the engine, the fuel line comes out the bottom of the tank, and if there is no fuel filter, goes to the Carb. on the back side.

Click to expand...

Never mind i got that fixed now it just needs the screws adjusted on the carb now. Sounds like a nascar or is that normal?