toro

Does anyone know how I can find this exact screw for my mower? It's for the black cover on top of the carburetor. Model # 20332 serial # 310038425.

I searched the forum but couldn’t find any leads, at least not from the last few years. Does anyone have a source for possibly finding NOS 22040 parts? Specifically carb, air filter cover, or a coil? I’m trying to help a friend get one in good running condition but obviously they have not even...

I have a fabricated deck off of a newer toro mower. Over the winter I fabricated it to fit my 1998/99 Toro z master 150. Better cut than original. There was nothing left of stamped steel deck. It uses the original belt, tensioner and pulleys. Only spindle pulleys are different. Ive put over 50...

Hello, 1- I have a Toro 21090 electric lawnmower, 21090 cutting width, which I've had since 2007. I just hit a stepping stone. Since then, the mower has been making an unusual noise, so I haven't tried using it again. The blade doesn't seem damaged. It turns by hand, but with a little force...

I have the above mower. Not sure what model Briggs it is, but it has the automatic choke connected to the muffler, with a control rod. Symptoms vary. Sometimes it starts and runs. Sometimes it doesn't start. When it does run, it will sometimes go until I have to empty the bag, then it won't...

Recently I bought my first zero turn mower, a Toro Titan MyRide 60." I mow about 4.3 acres; some really smooth and some really rough. Love the MyRide feature on the rough parts--it has been great for my back. Model number is 76614. But the other reason for the upgrade was to finish the job...

I just acquired a 21199 serial 4008… The guy I got it from said he was trying to fix the transmission. Problem being a loud screech when the transmission is engaged. He said he replaced the belts all 3 of them and it did not help. His take was that the transmission needed to be replaced and he...

Hi, Old Toro Wheel horse, 14 hp, Model No 71283, Serial No 240000104? Does anyone know the make & model of the gearbox (GB), recommended oil & quantity. The mower is going well, however there is a very slow leak from the GB & today there seemed to be an unusual noise from that direction. I...

A convex spring washer is used to hold a V-belt pulley tight. I assume the washer needs to installed so the convex part faces up towards the nut? In other words the raised center section of the washer faces up?

I have this Timemaster mower and while I think it's a great mower I cannot figure out one thing. Serial number starts with 313. I have replaced the pulley on the blade shaft where the belt on it goes to the engine, the shaft, and the spindle. The pulley was held tight by a locknut and under...

G'day gang, Yes I now fully agree my last posted question re: 'how to hotwire' my Toro ride-on was foolish & not well thought through. Possibly bordering on sacrilegious to some members. Panic & lack of knowledge got better of me & no disrespect intended. So.... I'm hoping...

Hi, I have the above captioned mower that has a priming bulb. After repeated priming the plug does not even look wet....however if I put a few drops of gas in the cylinder it fires right up. How best to trouble shoot this? Thank you

I've already reported this to Toro, but when they "updated" the MyToro iOS app and renamed it Toro Haven, it now crashes on launch on my iPhone. Lots of reports of the same behavior in the app reviews on Apple's store. My PUC is now a paperweight since I can't run the app. And yes, I have...

Thanks for the help in advance !! I just got a zmaster 286E and have a question. The control arms are auto returning to neutral from the reverse position when let go of but not the forward position, they just stay where ever they are and mower keeps moving forward. Like cruise control. Is this...

Thanks for the help in advance !! I just got a zmaster 286E and have a question. The control arms are auto returning to neutral from the reverse position when let go of but not the forward position, they just stay where ever they are and mower keeps moving forward. Like cruise control. Is this...

it will start when cold most of the time .. but sometimes when warm or hot it is very hard to start any help would be welcomed James

it will start when cold most of the time but when warmed up it sometimes is very hard to restart has a Kohler kt-715 on it any ideas would be helpful... James

Hi all, Long story behind the work done on this mower...the most recent thing done to it was to replace the wheel bearing on this wheel....but unfortunately used it today and still grinding. I thought the pinion gear was okay....when I activate the drive with wheels in the air there is no...

I've got an almost 30 year old Toro 20449 (GTS2 - SN:7901137) that doesn't seem to have the power it once did. I can't find an engine identifier anywhere, but it's a 5 hp Briggs. I bought it new and have only put and hour on so per year on it as I only use it to mow one hill. Even though the...

Hi guys, Just had this mower apart to install a new belt as the self propelled drive did not seem to be working well...runs fine now and the wheels drive, but there's an awful grinding noise coming from the rear left wheel...especially on a slight slope when thats the downhill wheel. Took the...

How do you get head off 60volt trimmer model number 51830

Just removed the bowl nut from the carb on the above noted mower as it was surging.....cleaned out orifices in the bowl nut so fluid was passing through all three holes freely.....re-assembled, and its still surging.....complete carb clean required?? Briggs and Stratton engine Thanks for any help.

Greetings all I picked up this TORO 210-5 mower, it runs great. Currently updating the drag links and tires and will be sharpening the blades. But i noticed it doesn't have headlights.. not that i would mow at night but i think they might be handy. I tried to find a headlight kit or a...

I'm having difficulties with current mower. Might post in repair forum side. But considering buying something. I am semi-competent at tearing them apart and minor repairs, so would consider low priced used mower. Don't want self-propelled. $369 Toro 140cc seemed to have the best reviews for...

I was going to do hydro oil change on my Toro Timecutter Myride 60 inch mower to find a nasty surprise. There is filler plug on top of transmission, one per each side. I am blessed, I knew well enough to ALWAYS open filler plug before draining any oil. I found that filler plug is covered by...

Picked up a 1984 Toro TV 5004 Bagger No discharge chute, But runs on starting fluid Anyone know what these are used for And is it worth fixing Thank's for any info

I have a Toro I think it’s a recycler model , number 20381. I have a bad transmission on this lawnmower and I can’t seem to find a replacement. Is there any transmission will fit in this lawnmower that I can replace the one that I have? this is a rear drive lawnmower. Is there some transmission...

I have an old Toro Recycler 22 inch self propelled mower. it runs great but the handle bar is way to low. I'm hunched over while using it. Does anyone have any ideas for the best way to fix this? I considered cutting the bars and rewelding them up at a slight angle, but it's a pretty janky...

FWIW, I've been mowing the same acre of ground for fifty years, so I know it pretty well. The all-around best mower for the money was a Simplicity 30" 8hp tractor style. The little B&S ran for thirty years and was still running when I sold it. Two Cub Cadet tractors, a 12hp and a 16hp Kohler...

I was mowing, everything worked great. Suddenly the PTO mower disengaged, quit cutting grass. So I rode the mower back to the driveway, which is about 50 yards from where the mower deck quit. I checked to see if something out of order. I tried to restart the Toro, only clicks at the starter...

This is a 22" Toro 20333 rear wheel drive personal pace recycler. The BBC belt broke. When I took it apart I found this mangled part that looks like it was a flat washer. I don't see anything like it in the parts diagram. The diagram shows a different part (#20 in the diagram). I ordered the...

Hello.....drive on the above captioned mower does not work..... Belt is on both pulleys and seems firm Belt drives blade no problem Both wheels turn freely by hand when off the ground. Any help appreciated. Thanks

Hi all, Cannot get the pinion gear off the end of the drive axle......copious amounts of Deep Creep penetrant over 3 days, and also heat from a torch to almost red hot.....still won"t come off!!! And in trying to pry it off I've destroyed the plastic washer that sits behind it, so in order to...

Not here often but when I fix something like to share. My mower is pretty old, burns some oil, but keep fixing it. However, I had a few times over the years I broke the string, so decided to change the whole recoil. First time changed and original owner. How did this recoil last that long...

2021 Toro myride 54 in is humming and pulling to one side.gets worse as I make turns, can cool down and it works better but still hums and pulls.. Help

Hi, The original B&S 6.0 GTS quantum engine on my super recycler is losing compression and slowly burning more oil. I'm guessing the end is near for that engine. My plan was to buy a new 725EXi with a 25mm x 3 5/32" shaft for this mower when the original engine dies. I was planning on buying...

I have a toro timecutter 4250. last week one brake would not disengage so we took the linkgage off so we could cut. Now, the cutter sits in the garge by itself and make a clicking noise, almost like it wants to start. its sporadic clicking

Replaced solenoid, turns over. No spark. Got a spark when going from starting to run position. No spark when cranking. gas ok. switched small wires, wouldn’t crank. Put them back, cranks over, but nothing. Help!

Heard a click when I went to start it. solenoid was bad. Replaced.Now it turns over. But no spark when cranking but got a spark on run position. What’s up? HELP PLEASE!

I have a Toro Self-propelled mower with the 3 speed Lever at top. Can the speed be adjusted. Even in the third position it is too slow for me.

Hi, new to the forum. My Toro is second-hand to me. The electronic brake controller failed along with the ignition solenoid, as it sat outside over the winter. (we moved recently, and shop was full) I replaced the brake controller, solenoid, battery, and ignition switch. Now it will start and...

Brand new Toro Timecutter Max creeps forward in neutral and tracking wont steer straight.

After cutting the lawn , put the battery in the charger and red light started blinking and even after charging overnight it still was blinking red. Measured the battery voltage and it was over 52Volts. Can the charger be bad? Anyone know what the 5-6 terminals are? I know the 2 outsides one are...

I have a Toro Z5035. One of the drive wheels won’t turn. Even with the transmission disengaged it still won’t turn. I can feel the motor lug down when I push the lever forward or back. The lever also feels stiff when I do this

Ladies & Gentlemen, I seek your wisdom. My mower will start fine but when cold it takes several minutes of sputtering and puffing black smoke to decide to speed up and run. It has new carb, coil and plug. Once it warms up and starts first pull every time and runs fine.

I have a 2003 toro push mower that has worked great and has had a few tune-ups over the years, last year where the primer push button is, it leaks gas especially while mowing and when the gas tank is full,even while not running until it gets to a lower level of gas in the tank. I took it to a...

How in the world do you raise the seat on this mower? Its the time cutter with the battery on the right side under a cover. I need to get at the parking brake switch.

I need a new carburetor for my 2006 Toro SR. My issue is that my SR (6.75hp B&S) has an oval air filter on the right side of the motor. None of the carbs I have bought (used part number from book) have a primer hole that lines up with the air filter adapter which is where the primer bulb is...

Scratching my head here. Worked fine last time used. Set in garage through winter time. We had some cold weather, maybe down to 17F for a night or 2, but that is gone. I tried to start the engine today - no go. 1. starter spins fine 2. tank half full 3. Choke up, as it should 4. PTO down, as it...

I have a TORO 6.5 rear wheel drive that needed cleaning, so I took off the rear wheels to clean out all the thatch packed there, replaced the wheels and now it acts like the gears are stripped. What did I screw up please ?