drive

Model #934596 Hydro Gear ZH-JCBB-3EMB-2PPXX I’ve had this mower 10-ish years & it’s done a pretty good job. I’ve gotten accustomed to replacing the drive belt or tensioner spring / pulley / bracket regularly, never thought much about it. Earlier this year I discovered the broken hystat motor...

Hi Guys My son has an older White 2055 garden tractor that the drive shaft is starting to go, he has to lubricate it before using. Question= can we rebuild the drive shaft? If yes does anyone know the part numbers and where to buy them? Thanks John O

New'ish to Forum. I am new to old ExMark (pre-Toro) mowers. Have a 2007 unit that blows drive motor seals. Still have original Parker motor that leaks and a replacement motor only lasted about 4 months and now leaks. Both were seal leaks as far as I can tell from owners' description...

My rear axle broke and its a discontinued part. Anybody know any other brands that would work or used one or anything?

Hi there, working on neighbour's Self Propelled Lawnboy. The cogged belt was broken and the drive belt is worn & cracked. We ordered both belts from Amazon and the cogged belt was a perfect match & installed. The drive belt is another issue. Part # for the new drive belt according to the pdf...

Hey there! The splines on the transmission drive pulley are stripped and I haven't been able to find a replacement. Other than welding the old one onto the output shaft, does anyone know of an alternative part number to search for? A. It sure seems like a common problem B. It seems like this...

My Honda HRR216 self-propelled mower has been kicking my butt lately because the self-propelling feature stopped working and it has turned into a push, push, push, mower. This mower model has an issue with the rear wheels locking up when pulling it backwards. Honda issued a service bulletin...

1st time this has occurred. Mower loses drive. Initially freewheel control lever had relocated itself to back position (freewheeling) while mowing. Reset. After more mowing it lost drive again. Freewheel lever won't hold back position but freewheels anyway. After some idle time, will reengage...

This old work horse just keeps going. I have noticed a lot of drive belt flop. I recently replaced the deck clutch and can see wear on different parts that the drive belt is flopping against. It didnt seem very tight, so I adjusted the idler on the pivot a small bit. It still flopped around. The...

Hi all, Long story behind the work done on this mower...the most recent thing done to it was to replace the wheel bearing on this wheel....but unfortunately used it today and still grinding. I thought the pinion gear was okay....when I activate the drive with wheels in the air there is no...

I have a Snapper self-propelled walk-behind (can't remember the model and its raining cats, dogs and big frogs; so I'm not going to look :eek:). The mower went for about a year without being used (but started on first pull with new gas). I used it today and discovered that the drive disc is...

Hi, I have a Mountfield MTF 84H riding mower. Does anyone know the best way to put a drive belt that's come off, back on? Any suggestions welcome!

Trying to change the bearings on the drive shaft I have the wheels off and the transmission out. But The left drive wheel was attached on a splined shaft. I have the left wheel off, but the bearing will not come off the shaft because of the spline on the end of the shaft. How do I change the...

Hi guys, Just had this mower apart to install a new belt as the self propelled drive did not seem to be working well...runs fine now and the wheels drive, but there's an awful grinding noise coming from the rear left wheel...especially on a slight slope when thats the downhill wheel. Took the...

Trying to remove the drive pulley and wondering if the pulley has to be unscrewed or just removed by heat and tapping. There are threads visible inside the bottom of the pulley but nothing I can find says it has to be unscrewed. There is no bolt from the bottom. Possibly it fell off but it's an...

Well, the title sums it up. I have the mower in the shop and the guy says parts are back-ordered from the factory. Been a week or so. Probably will never come in I guess. Tried to find something on the 'net before coming here. No luck. Any ideas? Thanks.

have a grass hopper 712d mower, the disc on the drive shaft needed to be replaced, in the process of replacing the disc on the drive shaft, everything does not appear to line up correctly, the unit that holds the discs to the shaft are difficult to replace the screws and nuts.

Hi all, Just replaced the belt on the above captioned mower, and made sure all bolts were tight, however the rear left wheel keeps loosening and falling off. I suspect that the threads on the pivot arm may be stripped,but it shows no sign of this visually.....anyone else had this problem or have...

craftsman t1500 247273740 came to me with a broken wheel drive belt i found the belts but there is no diagram under the tractor. i can not find the routing for the belt. you t search did not find any thing that looked like this machine. any help would be appreciated.

I'm starting to tear my GT5000 (917.275972) down to replace a broken ground drive belt and had a question about one of the pulleys underneath. The transaxle pulley and the two pulleys on the right side of the frame in front of it seem fine, spinning freely, but the pulley closest to the PTO...

I am looking for idler pulley GC00674 and Transaxle AM131850 - is there a replacement or a way to fix issue with drive shaft from transaxle damage from pulley. Drive belt broke and in the process of replacing it noticed the idler pulley had excessive wobble due to excessive wear on Transaxle...

Any recommendations for a gas powered self propelled 4 wheel drive lawn mower?

Just replaced the belt on the above model, and noticed when I took all apart that the blade driver has no protrusion inside to fit the key way on the drive shaft. Just wondering if its sheared as I see no evidence of there having been one ....perhaps this is why it's not self propelling? Should...

According to what I have found the engine drive belt is supposed to be 5/8th by 91" so ordered one off of EBay. Now this is not OEM, and I am beginning to believe it may not be the proper belt. I have the PTO and drive pulley removed and in trying to get the belt back on the drive pulley...

Model 53AA5A7M710 Serial 1H024Z00013. 360 hrs. This past week I have had an interesting zero turn that the hydro drive totally quit on. The nylon tensioner pulley locked up and the drive belt melted it in half. It goes without saying that the deck has to be removed before digging into one of...

Model 53AA5A7M710 Serial 1H024Z00013. 360 hrs. This past week I have had an interesting zero turn that the hydro drive totally quit on. The nylon tensioner pulley locked up and the drive belt melted it in half. It goes without saying that the deck has to be removed before digging into one of...

This is a 22" Toro 20333 rear wheel drive personal pace recycler. The BBC belt broke. When I took it apart I found this mangled part that looks like it was a flat washer. I don't see anything like it in the parts diagram. The diagram shows a different part (#20 in the diagram). I ordered the...

I have an R21, and after a year, just got a flat Drive tire. I have a couple of floor jacks. I've tried jacking up the frame just behind the wheel. However this causes the mower to articulate. The rear lifting while the drive axles lower. I'm apprehensive to use the hydro box, located just...

Hello.....drive on the above captioned mower does not work..... Belt is on both pulleys and seems firm Belt drives blade no problem Both wheels turn freely by hand when off the ground. Any help appreciated. Thanks

Looking for a more aggressive tread versus the turf tread to provide better pull up a hill. Any suggestions? I'm driving a Toro 20092, Serial 29000xxxx

The drive belt on my 2025 Rogue broke after only 7 hours. you can see a pattern of nicks around the belt in the pictures. I don't feel any burrs on the pulleys, any ideas what might cause this?

Hi all, Cannot get the pinion gear off the end of the drive axle......copious amounts of Deep Creep penetrant over 3 days, and also heat from a torch to almost red hot.....still won"t come off!!! And in trying to pry it off I've destroyed the plastic washer that sits behind it, so in order to...

I am the owner of a two-year-old HONDA HRX217 versa new mower. This weekend and the past weekend, a problem has risen. After starting the mower shifting to high speed I engage the mower blade. It growls a bit. Then I engage the drive and all speeds except the last, which is fast and then it...

Good morning. My Craftsman GT6000 (917.288612) doesn't want to move forward with the pedal to the metal. I decided it was the drive belt. It should be here tomorrow, but no garage and it's supposed to rain for days. Ugh I watched some YouTube videos, and it seems straight forward. You know it...

Gravely 992276 proturn 472 kaw drive belt spring mine broke. going to get one from dealer. ref 9 part number 08300507 any instructions or precautions on install ? any mods or changes from the factory? it has the eyebolt to mount on chassis. goes around idler mounting bolt I help my daughter...

Hi, I have a circa 2008/9 ZTS 6000. It “naturally” decided to stop any movement - at the back of the 5-acre property, away from my shop, with incoming rain storms. I removed the deck, the belt is intact, but off the tensioner. I tried to put it back on, but the belt tensioner assembly is...

Working on a Model 934778 60". The mower had a broken drive belt. I replaced the "broken" drive belt and the idler pulley. The belt, cogged, look hardly used, and the idler pulley bearing was tight. I put a new belt(cogged) on along with a new idler. I started the mower up, warmed it up a...

I got mower out today, for spring cleanup. I had very slow forward, no power in drive and almost no reverse. does it have fluid in rear for drive ? Any advise, Thank you.

Hi everyone I tore my 1994 gold series down including the rear wheels and transmission to repaint the deck I took pictures and thought I put it all back together correctly but noe when I tried to move it it free wheels going forward and lock.s up pulling backwards. I've not started it yet thus...

Hello Everyone! I own the mower posted above; just purchased it last year. The gentleman who originally owned it mentioned one defect that it arrived with straight out of the factory. The tensioner spring for the drive belt rattles against one of the hydro pulleys at mid-low to mid-high...

Snapper Model 130.887650 Dual Stage 27" 11.5 TP Snowblower Wanted to replace both driver and auger belts, however could not figure out how to do auger belt as can't quite get clearance to remove drive belt as well as replace new one. The square metal plate on one side and the friction wheel on...

I have a TORO 6.5 rear wheel drive that needed cleaning, so I took off the rear wheels to clean out all the thatch packed there, replaced the wheels and now it acts like the gears are stripped. What did I screw up please ?

I acquired a 2009 GT2142 recently that had been parked for at least a few years (235 total hours). When I got it cranked and took it on a road test, the driveshaft went to banging and came off. I discovered the blue needle barrels on both engine and transmission end had “collapsed.” I watched...

I have this Worldlawn 52" Venom stand on mower that was left at my house by my bother so i have been using it and the drive belt broke. I have the correct belt and the user manual and the parts manual from the website but there are no instructions for changing the drive belt. Does anyone know...

I just took the shaft out to lubicate the slip end. Dropped the parts and can't figure how to get it back together, Thanks

My brother passed and I inherited his collection of lawn mowers that he used for his 1-man show business. The mower in question was loosely covered with a plastic bag and left outside for 2 years in NW Pa. I am in the process of evaluating if I can get it running again and discovered that the...

I have a Lawn Boy Insight walk-behind mower, Model 10684, Serial No. 250029123. The self propelled drive stopped working. I can push it forward but wheels lock when trying to pull it backwards. It happened on my last cut of the season and I won't be able to work on it until spring. Anyone...

Hi there, just bought this for my son. The seller said that belt just needed to be replaced. I replaced it but the drive does not seem to engage. The transmission is tilted forward so the belt can’t engage the pulley. If I manually rotate the transmission back to engage it works. There does not...

I need help with replacement of the tensioner pulley for the drive unit on a SFZ 48-22k. There are two, one is stationary that is the one that blew apart. I removed the bolt and reinstalled it in this picture but there appears to be part of the old one that is pressed into the frame. Not...