Search results

I have not do that for a while so I don't remember the exact location but I use a long 10 mm socket jammed in flywheel to lock it in place to remove the nut in the clutch

Compare GXV140 and GXV 160 you have difference 5HP and 5.5 HP and that was the spec more than 10 years ago .Now they dont made GXV 140 any more and look at the spec of GXV 160 on Honda now you will find out it have only 4.3 HP that because they try to reduce pollution ,lately HRC216 not for sale...

Thinking to replaced my Echo trimmer with Honda .What do you recommend 25cc or 35cc

Unlike other Honda lawnmower HR21 use GV150 engine ,not overhead valve,its flat head and only 3.5 horse power .I found that its difficult to work on it as parts is hard to find and too expensive .Last time I work on this mower still can 't get it run right,running too lean

I having trouble to find a carburetor for this one HR21 .May try to modify GCV carburetor to use on this

I have HR21 but rear wheel have metal gear as you said its newer style .I dont think it will work even the 2 gear may match up fine but its will move backward

Sorry to hear that

Also if you buy that engine make sure it have PTO shaft to drive your trans.

Yes,it should fit,but GXV 120 is little weakj .I would find a good used GXV140 or even GXV 160 to install on HR214,It fit perfectly,just make sure it is SX or SXA model,HXA model disign to use on hydrostatic trans with dif gear ratio

Need to remove the bracket by remove the bolt above the light spot ,also remove the cable then slice carburetor out

I'm sorry the bolts shoud be 40 mm long

That's good,here is how you mount the blades,also use longer bolt ( 35 mm ) and heavy washers

You need all 3 Items below to get it mulching good 1-https://www.ebay.com/itm/HONDA-HR214-HR215-ALUMINUM-CHASSIS-MULCH-PLUG-MULCHING-PLUG-76266-VA3-J60/193438059531?hash=item2d09ce8c0b:g:qjgAAOSwQJ1em0SI...

You got same power as new HRX217 .With the mulching kit you have a mulching blade mount on top of the high lift blade and with mulch plug .Your grass clip as fine as the new HRX217 mower . Not as fine Compare to the Toro recycler

You may have to spent 100 for a good used trans from HR215,ask them to included all cable and do what I said about .IUt will out last the new HRX217 with Chinese engine ($600)

Very hard to find a trans for your HR195 .I collect these mowers,have several Hr216,HR214,HR216 but only 1 HR195 .Its 19" mower so the rear shaft also 19".You may find the trans for HR215 or HR214 and cut off about 1" both side (best is to math the lengh both side with your trans ) then tape M8...

I'd re-ring and hone the cylinder a little ,lapping the valve then it run good ,never see cylinder that worn out to out of spec on these engine ,Piston sometime need to replace .

I used to hate to cut grass until I first try the HR214 that I pick up at scrap metal,since then I have some fun on yard work and start to collect several Hr214,HR215 and HR216 .All use the same deck,same blade,same blade clutch that you can swap around .HR195,HR194 have smaller deck but they...

the SXA is gear driven trans that ran good and last ,howevver when engage sometime it lift up the front end a little cause not even cut (some people say that )but it don't bother me at all .The HXA driven by hydrolic pump and you get very smooth when engage and variable speed depend on how...

Most pressure washer pump will fail before the motor fail.however new crankshaft cost about haft the motor plus you will need new gasket and lots of work

I like the HR215 HXA more than the HRC216 HXA . First is the weight,the HR215 with alloy deck weight 101.4 lbs whilke HRC216 with steel deck weight 121 lbs .Its 20 lbs different Second is the power,the HR215 with GXV 140 produce 5HP at 3600 rpm and normally when come out of factory its close to...

That's exactly what I done for my HR214,HR215,HR216 .The correct size for rear wheel drive shaft bearing is flange bearing 15x31x11 in metric .You don't have to buy expensive bearing as these are low speed but need good seal .If the shaft worn out a little is OK .If it worn out too much you have...

I think the guide bolt is missing or come off .That is the only way transmission can move too far out

thank you for the gap,I set my too tight,though as close as possible

I have Harmony HR215 SX,transmission is broke but engine and all 4 wheel are very good condition ,I also have the plug for mulching .If you live in Houston I sell it for $50 .

Look for cable first,there are 2,one to shift gear,another to engage the transmission

Replace wheel bearings for Honda HR214,HR216,HR216 (all alluminum deck ) 8" wheel Honda original bearings are good but no seal,allow dirt and water get in,get rusty after few season .I have been replace them with cheap bearings bought on Ebay but they have seal so it last long time Front...

My old lawnmower Honda HR215 K1HXA got flooded during Harvey storm last year.Now the house all fixed,time to take care the lawn mower.I already get the engine running,replaced all cable,clean and oil all bearing for wheels,cluth for rear wheels but trans.make bad noise when engage .What is the...