Search results

Thanks to everyone that responded! Figured it out At first all safety switches tested good but I went back through them and the one on the right lap arm tested bad. Luckily I had one in my shop. Fired it up and released the park brake and it stayed running

Well I finally got the seat delay module in this morning, installed it Repaired the carburetor linkage and cleaned the carburetor. Fired right up but when I went to release the park brake it still dies. I’ve checked all of the safety switches. I’m at a lose at this point

Here you go

One thing I haven’t checked. I also checked out the seat delay module and it’s good

Yes sir. I’ve checked all of them

Seat and park brake safety switches are good. When I start it it runs but as soon as I release the park brake it dies. Any information would be greatly appreciated

Has a Kawasaki fr 651v engine. new fuel, spark plugs, new fuel line and carburetor and fuel with filter engine surging and when I engaged the blades it dies. any idea what it could be?

Have a buddy that had one on a mower with a blown engine I was out $100

Wound up being the left transaxle. Had to replace it. Thanks again for all of the help

Appreciate it I’ll look at it tomorrow

Looking for help. it tries to move forward and backwards but only moves a couple of inches I don’t see a hydraulic reservoir on the mower. Tension spring is ok and belt is in good shape. any ideas would be greatly appreciated

Figured it out. Shear key was bad. Fires right up

Here they are

Standby and I’ll send them

I’ll get them tomorrow

Engine turns over but just won’t start and run

New carburetor, fuel and fuel filter has spark but won’t crank and run. any help would be greatly appreciated 🇱🇷🇱🇷

Well good news this morning Got the parts in this morning that were broken. I cut a new shear key. Got it back together and it busted off and ran on the second pull Thanks again for all of your help Greatly appreciated!! 🇺🇸🇺🇸

Without the washer and nut on it , it has slack in it. I’m going to install a new shear key tomorrow and see what I have

I just pulled the flywheel and it’s solid but it rocks back and forth as it’s got slack in it.

Yes sir I did look at it from the top Since you mentioned it I’ll pull the flywheel because it’s a possibility that it might be messed up on the bottom of it. It looks good from the top

I have a brand new Briggs and Stratton 7.25 eco engine on a push mower that has fire but the flywheel cup is broke off in two places.its made of plastic. Plug has a great spark Will this keep it from straying? Only had one tab left.

I replaced the left brake cable and that fixed it.

Here’s a picture of what I’m seeing

I don’t see any springs. Tried to upload a picture but even after reducing it it says it’s to large

Appreciate the information I’ll have to look and see when I get back home I’m not seeing item #22 though I see the 10 & 20

Appreciate the feedback Startech I just ordered the spring You know anything about the brakes? It’s not the brake cable because it engages fine. It’s just that when the brakes are released, sometimes the left will stick

Did that and nothing came up

I am having an issue with the left brake not releasing. I’ve sprayed the cable. Sometimes it’ll release then some time it doesn’t. another issue I’m having is the spring for the drive belt tensioner broke and I can’t find one. Need a part number. Even looked on bad boys website and can’t find...

I purchased and installed all of that

Bzt48kt74003180289 is the model number I put in new o rings as well The kit I purchased from Badboy had all of that

I have an issue. The transaxle was leaking so installed an upgrade on both since they are bad about warping. they are both still leaking oil and I tighten the bolts to spec. Any help would be greatly appreciated

is there a way to test the controller? all i have is a volt meter. do you think that when its getting hot it fails?

they are good but the issue is when it dies and i turn the key the mower doesnt make a sound or even turn over

the mower will start sometimes and run for a BIT THEN DIE. then when i try to start it , it doesn't make a sound. I also noticed that the fuel solenoid doesn't click but pulled it off and it works but not on the mower. all my fuses are good. when it wont make a sound the amber light on the...

put a new battery on a MTD rider mower MTD13AM675G062. had to charge it overnight and when I tried cranking it, the motor wouldn't:2cents::confused3::confused3: even spin. it just moved. looked the charger at its back down in the yellow. could the ignition switch be faulty causing it not to...

this tiller has a 3hp H35 Tecumseh on it. I put a new carburetor and spark plug:confused::confused: on it. I've got the side screw out 2 turns and bowl screw out one turn. wont stay running. any suggestions.?

model number 10403A poured gas in it and gas runs out of the bottom. fuel lines are good.:anyone::anyone::anyone: also need to know to remove tank from saw.

model number 09p702-003-F1 when you crank it, top lifter jumps off push rod and valve spring.550 OHV Briggs and Stratton motor. any suggestions.?:anyone::anyone::anyone:

got mower going , engaged blades but they wont turn. any suggestions.?:anyone::anyone::anyone:

Folks, I have a 2004 Poulan riding mower. the transmission is in neutral and I have the rod pulled out but it won't free wheel. any suggestions.? :welcome::welcome: