Search results

I have seen whose fancy aluminum wheels on some race mowers:thumbsup:, would they be good on a RER for mowing ? Where can I find some? does anyone make wheel covers for stock wheels ?

I saw a post about where you keep your precut trimmer line when trimming a large yard so you dont have to run to truck for more line. But I cant seem to find it. Keeping in my pocket doesnt work to good. I was thinking about keeping it on trimmer some how? Who's got the best way?:rolleyes:

I have an older model Murry Rear Eng. rider that is very hard to change deck heights.I was thinking about bolting some chains to the deck and use bolts on rider frame to change heights or does anyone have a better idea:thumbsup: only have two yards up high and three down low:confused2:.

I have a TVM220 on my broken rider which I no longer need:frown: ,I put The 220 on it brand new, and I have a push mower that needs to be repowered can I put the 220, 10 hp on my push mower I know thats a lot of engine for a push:wink: but I dont have any other use for it?

I want to make a pull behind aerator , How long should the spikes be? I have a couple of pipe sections that are about 2" differance in diam. I plan on using nails in one and using a crack sealer between the two, with a rod running through the middle to hang weights on, all hooked to ends with...

I have a unknown model Murry RER that I cannot get to shift,the trans.a 5 speed has a sticker on it that reads, SPICER #56191 with a date of 10/87. I am going to take it apart and see whats inside,I am hoping it just needs some oil or grease. what kind should I use ? I was thinking 90 weight...

My murry RER 8 an half 30" transmission, 5 speed +rev.spicer, built in 10/87 with #56191 on the sticker, will not shift very easy.:mad: Has anyone taken one of those apart? I guess I am going to find out whats inside:shocked: I want to put a grease fitting on it, what kind of grease should use...

Do you cut with a back and forth pattern or do you do a square pattern and why/:cool:

:cool2: I have a TVM220 10 hp Tecumseh on an old RER murry and I want to put a pipe on the exhaust so the heat doesnt hit my side panels. I want to run the pipe so it will exit the back and not the side. does anybody know the size pipe I should use?:confused2: With a couple Ts I can have duel...

:confused2: How do you cut a small lawn with a push mower, in a square pattern or back an forth.with no worrys about discharge :confused:

When I push the primer blub, gas comes out a hole on other side of carb:confused:. I put my finger over hole and primer works good. it doesnt change running when hole is plugged. B&S #10A902- 2291- B1/ 550 series. Also when I took shroud off it ran better, whats its for , just to look good...

My Murry rear engine rider is off to the scrap pile :frown: I have been trying to find where the model # is over in the Murry forum but can't get a response. :thumbdown: The mower broke a drive belt so I got a new belt ,took a lot of work to try an put it back when didnt know the proper routing...

:frown::confused2:I have had three days of trying three different belts :confused2: Putting it together four times,taking it back apart many times. Finely figired it out now all I have left to do is the belt bracket that keeps the belt on the pullys, of course I half to take more parts off to...

:licking::licking:I drove an 18 wheeler for 16 years,now that I have retired I find that runnin my little 10hp rider 30in, gives me a good feeling. I mow the yards next to me (both sides) for free just because I like riding my mower.I am not in the country I live in a city with small yards. Does...

:smile: Hello folks this is my first message. I have a 10hp Tecumseh TV220-157302L that has run very well in an old murry rear engine rider,lately it has started poping and running faster then slower, it dosent have any carb. adjusting screws, I checked plug looks good, new filter, Does...