Search results

Wire brush on a stick ;)

I used to be pretty big into brand loyalty... but that was before EVERYTHING affordable was made in China.

Vote your Trans-axle Lubrication of choice #00 vs Cornhead vs Bentonite vs 75-90 gear oil with Lucas oil stabilizer. mayonnaise

Hi all. So im mounting some tires on steel rims.. and i know some have suggested straight up dish soap.. but im concerned about the PH eventually rusting the rim. I have access to some lithium grease and silicon oil.. but then my concern is damage to the rubber bead. Also i have on the shelf...

So maybe a magnetic rechargeable flashlight? I was thinking something like this...

Greetings all I picked up this TORO 210-5 mower, it runs great. Currently updating the drag links and tires and will be sharpening the blades. But i noticed it doesn't have headlights.. not that i would mow at night but i think they might be handy. I tried to find a headlight kit or a...

I sanded down the wheel , painted them and put new sealed bearings and new tires and inter-tubes. all together it was as much as just replacing the whole wheel. but i could not find a whole new wheel with the correct diameter and backspacing as the old one. In this picture you can see that the...

I suck at welding but this should fix that worn out drive selector guide AKA lift Yoke.

When i was younger , one could get 20% nitro fuel (liquid dynamite ;) ) for the little RC gas engines and there were some places that would sell 35% nitro fuel. Hard to find real nitroglycerin fuel these days.😋

Make sure the oil level is not too full. some suggest running it below the "full" mark

So there are a couple of things i need to weld up on the snapper before i proceed . One of the things needing welding is the gear selection lift yoke. However i didn't have a welding cap to keep the spark and spatter out of my hair and ears, so i tried to make my own out of an old jean leg. I...

just out of curiosity.. is the current blade the same length as the previous blade?

Look closely at the picture.. something isn't where it's suppose to be. therefor contact.

well. first i would say #1 check your blade mounting bolts to make sure the blade is mounted properly. If that is ok then..... #2 check your spindle for looseness. If that is ok then...... #3 check the bolts that hold the shroud in place by the wheels, make sure they are adjusted properly and...

Engine covers: Leave Black? or Paint white?

finishing up the rims and adding new tires while i wait for transmission parts

I thought about doing that but there was just too much metal in the grease Looks like im going to need a new cover as well. this one looks like it would eat up any nylon washer i try to put in it. I suppose... i could fabricate a piece or metal to lay down in there and then have it tack...

Any ideas for a cleaning this grease off? i dont have a parts washer or a pressure washer. i was thinking maybe paint thinner? or something cheaper?

6 problems found in the differential case. The "half shaft" or outgoing shaft is work out the internal bushings are worn and the outside of the shaft is worn. this is going to be kinda expensive to replace. The internal nylon thrust washer is worn out as well as the metal washers for the...

Now entering the deep dark world of the differential case.

The clutch chain case is rebuilt and finished. I may add a couple of more bolts to the traction wheel

It's Rustolium Cherry red I got the decals from this link. Although the comet letters are too big. https://equipmentdecals.com/products/snapper-comet-2680-decal-kit-1973-riding-mower

I have limited knowledge.. but from looking at the photos i would say even though you have cylinder and piston damage i would bet that there is a problem in the crank case as well. Possibly a main bearing or crank bearing.

Progressing with the rebuild. Finished rebuilding the front end. New bearings and tires and steering bushings. Painted the frame. The comet decal is kind of big. Working on the chain case today

Greetings from NC yall. Ok so i finally pulled the trigger on buying one of those nice Snapper riding mowers. Yep that's right , im now a proud owner of a 1977 Snapper Comet 3010ws ( yeah i know , its old) I had in mind for a while of doing a restoration of one of these mowers so i could go Full...