Search results

Thanks, was able to find one from Mower Shop. Thanks for help

Hello have GH 725G2 w/mower deck #9852. I am looking for the lift assist bar that supposed to help release the tension on the deck chains for removal of deck. Looked at the equipment diagrams from the Mower shop but they dont show it. If you all might know the part # for the bar I might get...

Had just about the same issues, PTO would work but engine would sputter than die as it got hotter. Thought fuel filter, fuel pump but nothing worked until I looked at the distributor and found that the electronic ignition module was shorting out. Replaced module haven't had a problem since. 2004...

Wow to all of my fellow members great to meet you all from around the world. Names Rench been a member about a year bought my used 2003 725g2 GH w/732hrs, Kubota gas & 52" deck from school district auction. She's worn but still strong just needs TLC and alot of learning on my part as dealerships...

Never tried, guess it would depend on hitch & pin setup plus flat vs hilly. Let us know good luck.

Welcome aboard. Best advice is find closet dealer, download all info you can on mower, engine etc. to help with and service you might run across. My 725G2 is 2003 w/Kubota engine 52" deck just replace distributor ignition modules should be good for another 17years. I mow a 21/2 acre...

All right final update to ignition problem. Have installed new distributor w/ new ignition pickups, new cap, new plug wires put it all back together and she started right up ran for about 10 minutes, stopped to reinstall all of the other stuff (covers) and started her back up no problems checked...

Update: Tested distributor ignition for operational signal to coil and got nothing so am replacing entire distributor & plug wires. The electronic ignition pickup itself cost just as much as a new distributor w/ new rotor, cap & ignition components. Added plug wires into the mix as all of the...

Ahhhhhhh! That's where it gets sticky as so far no one and research has shown no body gives up the info on how to, so it's on going will try to keep you all informed.

No problems, took coil wires off, distributor cap and checked for shorts found none in wires, cap and coil still checks out. So how do you check the distributor ignition module anyone? Additional info; When mower died it was running and I had just finished mowing and was hooking up the lawn...

Hey Richie, please review post #6-10 and those earlier to get caught up, this will answer your question.

Well installed new coil and still no fire, yes I grounded it! I guess its on to the distributor. Any suggestions would be great.

Ok, thanks guys for responding to my question, I'll make sure I ground the new one. Now the coil I installed was an oil filled automotive coil chromed ( thought chroming was a ground ) where the original coil was OEM, but upon bench testing both coils the ohms matched spec what's up? Is there an...

Hello, I see that you posted this 2016, are you still having coil problems? Have you inspected the distributor or replaced? I am currently having the same issues (04 GH w/Kubota gas WG752E2) put a new oil filled chrome coil in and the mower ran great about 2 months than died again today, no...

Thanks, but any info on GH repair, upgrade, use is great news. Keep them coming. I've only used the GH mulch blades, might try Stens when I need new blades.

Was wondering if anyone has tried the Ballard X blade attachments on their Grasshopper mower ? Problems, results, noise, fit?

I've got the older deck 9852, with no rock shield just a bar across the yoke. Been thinking of getting a new/used deck that has power fold but there ya go money. Oh! well nice to dream of a brand new GH.

No expert here, but I seem to remember that an enclosed gear box w/no weeping hole uses its seals as the pressure relief mechanism. So it could, might be possible to blow oil past the input drive seal if over filled as I have seen on other applications of this design. I've researched the amount...

Bought a Scots (by JD) in 1999, still runs great but needed a better mower to get around 21/2acres. So found auctioned 2004 Grasshopper 725G2/52"/Kubota gas w/725hrs. Bought it for $3200 and have loved it since day one. Just did the service and she runs like a top. If I could afford it I would...

Read both of the your posts and I hope if I have to replace mine it comes a lot easier. Great info, looks like factory needs to recheck QA!

That's great. But I also discovered thru the research I performed on the form about this subject heat was also a major factor. Now prior to changing mine it was very difficult to engage the mower @ any rpm as she would die of until the motor warms up. Now after changing over to Amsoil FSYN. GEAR...

Still new but been researching same question thru out internet/forms and it seems the pros won't answer or can't but will point you toward the answer, because there is from regular people in this form/mechanic ?

Once again thanks. I was able to amass the information I required thru the links in this form.

Thanks Mark, I have tried prior to joining, numbers pretty busy. Thought others on form may know as it's come up in older posts.

Happy Easter all. New to Grasshopper/Form, bought used 2004 GH 724G-Kubota gas, Front mower #9852 w/737hrs. $2300. She came from school district. Anyway question is the front mount gearbox under the mower deck. 1. How do you remove the drive Sheave holding the gear box or any of the Sheaves in...