Search results

I made that power steering conversion on my Husqvarna 48-in cut with a 22 horsepower Kawasaki in my case I had to make sure that the washers were in the right place my spindle the vertical part that goes up through the A-frame so to speak with the eclip is on the top underneath that when I drop...

Yes . Your already in there and why not , and it wont hurt anything , TOMB

Thank you for your input Tom B

Looking for some input to track down the surging issue . Just started last week after I refueled the tank. Maybe some crud got through the older filter so- I changed the fuel filter slight improvement, next i changed the fuel pump -no changes surge continues, Coils are new, air filter new...

You need to do a plug check, The way its done with motorcycle engines is this Run the engine under load with the engine you have that is this ; Wide open cutting the grass etc. and with out bringing the engine to idle (keep wide open ) turn the ignition off then check the color of the...

If you need a good place for "00" grease try Tractor Supply. Cost me $5.00 for a quart. Look in the farm eq. section not the Auto Truck grease section Convert Tom B

Just taking a WAG . Try running the motor with the gas cap open/off (if that's possible) and see if the problem stays or disappears. Might not have any venting into the tank, (bad gas cap) Tom B

https://www.lawnmowerforum.com/threads/my-mod-to-my-gth2248xpc-with-22hp-kawi.61842/ This is also posted in the TODAY'S POSTS section CONVERT Tom

Here is the link to my pictures in my post above. Hope it works , Thank you @Scrubcadet10 https://postimg.cc/gallery/28JVNNK Convert Tom

The engine is a 22 horsepower Kawasaki FH 641 V I installed an oil cooler that fits the 721 version of the Kawasaki engine, the hardest part of the whole job was washing my hands, as a side note this engine originally did not come with the oil cooler, but the oil cooler for the fh721 ,it is is a...

I had the same issue with my GCV160, turns out the governor spring was in the wrong hole location. Or the governor are has changed position on the governor arm shaft. CONVERT TOMB

@de3 Thank you for your comment about my tractor I'm really enjoying it ,grandson enjoys it to thank you very much TOMB/ Convert

I run NGK BP6ES plugs in my 1976 Moto Guzzi Convert motorcycle. Engine looks and operates the same as my Kawasaki FH641v, both engines are 90 degree V twins, the only difference is the layout. The Guzzi engine/ bike ( 67000 miles) the crank is horizontal while the Kawasaki (575 Hours) is...

Here's mine. 2003 Husqvarna GTH2248XPC, 22 hp Kawasaki. See picture to the left Grandson optional TOMB

GTH2248XPC See profile pic to left Convert

Yes and proud to be a member. Convert

Honda with the GCV160 engine, 21 in cut . Just for the close up cutting , I use my GTH2248XPC for the rest of the yard Convert

Simplicity, 11.50 Briggs , 27in cut. For my application its the right size - weight etc. Convert

575 HRS . 2003 HUSQVARNA GTH2248XPC. FH641V Kawasaki In process of major tune up. So far---- New coils, Plugs . Fuel filter , Air Filter, Sparkplugs. Valve adjustment this weekend. Convert

AVB Thank you for your effort and supplying the diagram of the belt routing , i'm grateful that you took the time to highlight the part diagram. Your color highlights gave me the answer that was right in front of me . Thank you again Convert Tom

Riverts Thank you for your input. I'm in no way biting the hand/hands that feeds me. Like you i offer info on other sites that i frequent and people miss the message(i didn't miss your message ) and i'm not biting any hands. My expertise is different as we all have life experiences that...

Bertsmoibile1 Thank you for your reply. I identified my machine in the title of my post. I'm getting the parts ready to replace when the weather decides to start warming up. All i was asking if there is another diagram available other than whats in the owners manual . Thank you for your...

Thank you. Thanks I already have that Manuel, the picture in there is okay ,I can use it but I was looking something a little different, maybe an overhead view of the belts , what I see in this manual is like an angled shot ,and it's somewhat hard to trace the routing around the pulleys . Thank...

Does anyone have a drawing (picture) of the belt routing for this mower? There isn't any decal anywhere on the machine. There is a reference that there is a diagram on the deck (labeled Heavy Duty 10 Ga.) maybe it fell off over the years. I'm the second owner and i bought this from the...

Is there a tension lever on the deck?. If there is release the tension bar and you should have enough slack to install the belt. Done. Move lever back and lock in place. Convert Tom

Thank everyone. I repair Moto Guzzi motorcycles so the engine is very similar to the layout of my motorcycle . Moto Guzzi engine is a 90 deg. V twin , cylinders facing upwards. FS651V 90 deg. V twin cylinders horizontal. Looks like my engine fell over. With my experience working on Moto...

Thank you . I have this info and i appreciate your response But it doesent have the thread pitch and size. Thank you again. Convert Tom Bailey

First post so here goes. Model year 2003, verified by Husqvarna. What is the thread size and pitch of the drain plug? Right side if engine. Is it Metric or SAE? I've owned this tractor for a few years but it was used and maintained by my son in law at his location but I brought it to my...