Search results

Results 101 to 150 of 335
  1. F

    Found a bolt not sure where it goes

    Also look under the machine by the engine pulley and idlers. The nut on the bolt is a lock nut. So two nuts get tightened against each other with metal between. May be a threaded hole that it screws into.
  2. F

    starter howl

    If you can get it to drop down, spray clean and oil the shaft of the Bendix gear. It has to move up and down freely. You have to turn the gear for it to raise. The whirring sound should be the motor\gear spinning, but not rising up to the flywheel. My 2014 machine has been doing that the...
  3. F

    Are John Deer engines (Yanmar) reliable/durable?

    If I had to replace my machine, for my 2-3 acre plot, I would purchase a used steering wheel zero turn. I did that back in 2018 and have never regretted it. Spent a little more and got a commercial machine with the Kohler and 60 inch deck. I like the steering wheel as it tracks better along...
  4. F

    Mastercraft Yard Beetle issues

    With the carb installed and the bowl off, turn the gas on and it should run out of the bottom of the carb until you lift the float. If it doesn't, you have a restriction in the fuel line or a bad pump, if it has one. There must be a fuel filter. You should see gas in it. If gas is not...
  5. F

    Toro Recycler, Briggs engine quit working after oil change

    BEST WAY is to use your gear puller if you can. Alternative is to find a strong point of the block under the edge of the flywheel and put a small pry bar there, put the flywheel nut back on and leave a little high on the threads. Apply some pressure on the bar and a medium smack of a heavy...
  6. F

    54" BAD BOY MZ Magnum (zero turn) Blade Replacement OEM Blades - Blades Slipping

    Kinda reaching here, but remove the belt pulleys and blades off the spindle shafts. Clean and inspect the splines on both ends of the shafts and the mating pulleys and belts Check all idlers for correct alignment to others and spins freely and quietly. Check belt tension at all deck heights...
  7. F

    cub cadet rmc module will not work

    If you were to unplug the reverse switch at the trans, would it allow it to mow in reverse? I have done this on non-RMC mowers.
  8. F

    What makes it a mulching mower?

    I don't know if I missed the answer to the gent's question or if it didn't get answered. "What makes it a mulcher?". To me it means blocking off the shoot, adding a plug\baffle and mulching blades. I have 2 ZT, one for mulching my front lawn and the shoot for the back 40. The mulcher does a...
  9. F

    Best for hills?

    I agree with GearHead. I have a long sloped are and used to use a large Deere garden tractor. After falling off twice, I purchased a used CC Commercial with the steering wheel and a 60" deck. Even though I am more comfortable going up\down it does great riding the hill. The fact that the...
  10. F

    YTH22C46 Won’t Drive forward or reverse

    Does the mower easily free wheel? If not, check for a locked brake.
  11. F

    YTH22C46 Won’t Drive forward or reverse

    I also think brake is locked. Does the unit easily free wheel when pushed?
  12. F

    Cub cadet zero turn

    Toro has a separate key switch for the reverse cut.
  13. F

    Best for hills?

    I agree with GearHead. I had a very heavy Deere 316 tractor which I hated to give up, but it would not handle the hills. If I went along the slope, I fell off the machine. Going up\down, it would go down great but spin the drive tire on the way up. I went with a Cub steering wheel ZT and I...
  14. F

    Low Power and getting worse on INTEK 19hp (33R877)

    What is the symptom indicating low power? Speed decreasing? Blades turning slowly? If speed is the indicator, the trans itself could be the problem, especially if it's a hydro.
  15. F

    Swisher ZT2454 Won't Start / Blows Fuse

    The fuse is connected to the key switch and then to the solenoid and engine plug. Try unplugging the engine plug. If it still blows remove the small red wire from the solenoid. If it still blows, it sounds like a faulty key switch. If it doesn't blow with the engine plug disconnected, then...
  16. F

    Bad boy outlaw extreme shutting off after about 1 minute of PTO being engaged

    Check the tip of the anti-fire solenoid. I've seen a couple rubber tips get soft and swell. Blocks fuel past it. You can cut tip off for troubleshooting.
  17. F

    D140 Will Not Start

    Start at the battery. Should measure 12+ volts. Check both cables for tightness at both ends. Then go to the fuse, should have 12v both sides, then to the key switch, 12v on the B connection, red wire. Turn the key to Run+Lights, should have 12v at the L connection, red\white wire and lights...
  18. F

    Husqvarna YTH 2348 - Bringing it back to life

    Good list, but keep it basic. Start by checking, and maybe, changing the oil. Clean the gas tank and replace fuel filter and lines, if necessary. See if pump will pump gas at the carb. Check for spark then prime with cleaner to see if it sputters. Clean the side of the flywheel and coil...
  19. F

    Grass isn't cut between the blades.

    When cutting taller grass, weeds, raise the deck and cut then lower and recut. The front of the deck will flatten the grass and it may not have a chance to be sucked back up to be cut.
  20. F

    Craftsman Pro Series 8200 PTO cuts off and on

    I would go right to the seat switch and the reverse switch.
  21. F

    Issues with pto (solved)

    The white ring on the diode is the cathode, or negative end. As far as the replacement goes, if wires are attached and you can't see the ring, the black wire should be the cathode. The red wire is the anode or positive end. If you can get the raw diode by itself, it will be much cheaper...
  22. F

    Rider Mower battery question

    If you're replacing the battery, measure it first. 12.6v and it's ready to go. Anything less, charge it. If going to set for a long period, put it on a trickle charger. Easy as that. If you want it tested at an auto parts store.\, plan on leaving it for a while while they charge and test...
  23. F

    Fan rubbing

    StarThech, your assistance is valuable, don't let unnecessary comments cause you to leave. You have helped me out many times and I (we) appreciate you.
  24. F

    Murray 30 inch rear rider only sputters in low/mid idle

    If you bought a cheap aftermarket carb, I would suggest disassembling the original and cleaning it well. Cheap carbs do not run well.
  25. F

    New to the forum

    How can we help?
  26. F

    flywheel removal

    Whatever sealer you use, make sure it's oil resistant.
  27. F

    Riding or walk behind?

    Might an AWD push mower be a solution. Such as a: Toro 22′′ Personal Pace All Wheel Drive 163cc Briggs Walk Mower
  28. F

    2017 Exmark Lazer Z Model: LZX740EKC526T0 EFI Mower Will Not Start - No Clicks.

    I agree with StarTech, you must have 12v at the B terminal for anything to work. Test at the connector with the connector unplugged from the switch. Not having the wiring diagram for your model, you'll have to back trace from the B wire to the Pos battery. There may be fuses, switches and\or...
  29. F

    john deere d 140 transmission

    What is the original problem, or just routine maintenance? I have made hydro's better by replacing oil with 20w-50 synthetic and cleaning the filter, but if running slow and weak, it doesn't fix them. If that's the problem, a total rebuild is necessary and that ain't cheap. Make sure the...
  30. F

    Blade-balance oddity

    If you have a heavier end and it is down when the blade is vertical, it won't move. If you put it upwards, it will rotate. Being horizontal, it will rotate either way. I have an 1\8 in rod protruding out of the edge of my bench that I horizontally balance the blades. It is level and plumb...
  31. F

    Kohler CV491S Governor Problem

    From what I understand, a local fix-it shop made whatever adjustments to get it to run. It did run well, just had no balls when it needed. They wide open throttle cable was the issue with the plate. The choke screw had to be backed off to get the two holes to line up.
  32. F

    Kohler CV491S Governor Problem

    I agree, but I have heard on this forum to adjust the static adj any time a carb is replaced. I don't do that or any other time. This one had previously been adjusted to overcome replacing the gear.
  33. F

    Kohler CV491S Governor Problem

    The static adjustment was correct. It was the plate that was out. The tech used the wrong engine manual and the correct plate was not shown. With the Forums help, I got the correct manual and adjustment procedure. Thanks again.
  34. F

    Kohler CV491S Governor Problem

    With all your help, I have cured the problem. A complete adjustment of the throttle plate was necessary. Thanks again
  35. F

    Craftsman deck exploding

    Where are you getting belts? Stick to OEM. I have had cheap ones snap first time or very soon.
  36. F

    CRAFTSMAN 12-Volt 135 Amps Mower Battery

    I did check one store and all 8 mowers had that battery in them. If I was to purchase a mower there, I would insist the larger battery be installed. May work fine with a fresh tune-up and warm conditions.
  37. F

    CRAFTSMAN 12-Volt 135 Amps Mower Battery

    Hi All, I was at Lowes and glanced at the Craftsman T2400 series machines and noticed this battery installed in them all. It's a tiny 135 CCA battery. Much smaller than the U1 size. Everything I have worked on uses a 230-330 amp battery. Will this baby spin up an older 17-20 HP single cyl...
  38. F

    Kohler CV491S Governor Problem

    Measuring the steady speed with an induction type (spark plug wire) electronic tach. High quality $15 ebay product.
  39. F

    Kohler CV491S Governor Problem

    I moved it to the lower hole. Is that the same as shortening it? If so, it surges, but I don't think it sped up. It is not stretched and hard to stretch. It might be easier to drill a 4th hole in the arm between #2 and #3. I thought about a slightly longer throttle linkage arm.
  40. F

    Kohler CV491S Governor Problem

    Fingers and brains are not in sync. Max is 2900. Svc manual says: "If the high idle, no load speed is 3600 RPM or less -use the #2 hole (count outward from cross shaft).If the high idle speed is greater than 3600 RPM -use the #3 hole (count outward from cross shaft)." Even at the spec...
  41. F

    Kohler CV491S Governor Problem

    Well Rivets, you were spot on again. The tech used the 590 manual which is similar, but didn't show the correct bracket. Everything works well, including the governor, but the max rpm I get is 3900. Low is at 1400 rpm and no lean condition. Plate is adjusted all the way up. I messed with...
  42. F

    Kohler CV491S Governor Problem

    Hey Rivets, I'm gonna adjust that bracket later today. Another issue with this engine is if I adjust the idle speed lower than about 1500 rpm, it runs very rich and blows black exhaust. Anything above that speed and it runs smooth and clean.
  43. F

    Kohler CV491S Governor Problem

    Got it, thanks
  44. F

    Kohler CV491S Governor Problem

    OK, will do.
  45. F

    Kohler CV491S Governor Problem

    No, that's the PTO cable. Thanks for responding
  46. F

    Kohler CV491S Governor Problem

    Hello All, I picked up a Scotts Sabre by Deere 1752 with a Kohler Command 17.5hp single on it. Numbers are in the attachments. The governor went bad on the previous owner and he had it disabled by rotating the governor shaft CW and adjusting the throttle plate assembly. I replaced the broken...
  47. F

    Briggs 14hp IC not running right

    Try a governor static adjustment. loosen the clamp on the governor arm, hold the throttle all the way open, rotate the governor arm max CCW and tighten the clamp. Compression test may show the issue.
  48. F

    Stumped - Poulan Pro Snow Blower

    The red filters are for gravity fed fuel systems. I, personally, install the white\clear paper filters on all engines I work on. Both gravity and fuel pump operated. Never had a fuel related problem since.
  49. F

    Briggs 14hp IC not running right

    Here is a Walbro carb available on Amazon. I have ordered one to try soon: https://www.amazon.com/dp/B07XD8JSJZ?psc=1&ref=ppx_yo2ov_dt_b_product_details
  50. F

    Kobalt 2x 24v won't start and makes a clicking noise.

    One thing I have found out with the electrics, you don't clean the deck undersides with a hose as done with a gas unit. The person that gave me mine, had quickly power washed the underside and let it sit for over a week before using. It ran for about 10 mins and died.
Top