Search results

Results 301 to 350 of 440
  1. upupandaway

    help needed! Craftsman II 38" 12.5 HP model 917.254791 won't start

    If you have no luck finding a whole carb, you can also just replace the carb needle and seat: Needle and seat This is your cause of the fuel leaking(assuming the float moves freely up and down). That's strange how the carb lookup pulled up a push mower carb. This one uses a larger carb than...
  2. upupandaway

    What is the shelf life for lithium-ion batteries ?

    That's because they spot weld them from the factory. i cut around the weld. To each his own.
  3. upupandaway

    What is the shelf life for lithium-ion batteries ?

    Maybe not. if the battery case is held shut with screws, pull out that soldering iron and screwdriver - you can always replace just the batteries. Watch out as to not break the circuit board in the battery. Lithium batteries need this circuit to regulate usage and charge unlike NiCads.
  4. upupandaway

    Trying to find a manual for this old Snapper riding mower

    Just curious, what is bad that you need parts? If it is engine part then u can stop hunting for a manual and the engine model info is enough.
  5. upupandaway

    21hp I/C Twin Hard Start and Surging

    From personal experience, I agree with Fish and would bet cleaning out the bowl and the metering screw at the bottom of the carb bowl will fix your problem. I swear 99% of the time i find a mower that won't start(with carb problems) or won't stay running, this is the fix. Check the easy stuff...
  6. upupandaway

    Stand mower on end

    So you get a click when u turn the key?? If it is a pain to get to the relay, reach in with a metal rod and tap the relay a few times and try again. It just might knock loose the piece inside the relay causing your problem. At least it would tell u if replacing it is worth the trouble if it is...
  7. upupandaway

    LM21SW starting issues

    Well.....call me lazy but when shredding\bagging leaves, i got tired of having to restart it, I tied a rope to hold the safety bar for me while i dumped the leaves. Of course i stop the mower if i need to walk away and do whatever... Get a string and with the safety bar engaged(before u start...
  8. upupandaway

    LM21SW starting issues

    it would help if u post an engine model number. this model was made for about 30years so it was sold with many engines. It sounds like you have a carb problem more than an ignition problem. Does your mower have a rubber primer on top of the engine?(my LM21 does) If so press that 2 x and try to...
  9. upupandaway

    Wisconsin Robin Wi-185

    R u sure it is rod knock u hear? You can find out if it is piston slap you hear while u have it open, push right and left side and look if the piston rocks when u do it. If slap is from the crank journal, i guess you could gently turn the crank a hair back and forth while the piston is at middle...
  10. upupandaway

    Trying to decide on used Honda's - Which to get?

    With the honda honda mower u posted, remove the bag and there is a plate to the left. Remove the plate and see if the gear box wobbles\turns with the shaft forward and back. Being pretty old, the drive shaft input bushing wears out. If so, the gear box wobbles, and the gears don't mesh.
  11. upupandaway

    Wisconsin Robin Wi-185

    Yes, it is iron sleeve. Sounds like the bottom ring is not wiping the oil off the cyl wall or perhaps the drain holes from that ring are all clogged. If I were u, i would remove the piston and clean the piston and replace the rings. I mean it is 30ish years old.... While you are at it, rent the...
  12. upupandaway

    Rusty Gas Tank

    After you clean it out, if u want you can coat the tank so it won't rust again. I don't endorse it but i used the Por-15 tank sealer on my Snowbird many moons ago because after cleaning, it would keep rusting. I surely didn't want it to rust a hole in the tank.
  13. upupandaway

    Old Jacobsen 21 Rotary 2 cycle

    I think it is a Clinton. No clue on model but I hope it steers you in the right direction. Good luck at getting it to run. This one???
  14. upupandaway

    Peerless 205 Transmission - what bolt format?

    Can't you remove the bolt that didn't snap and find and take that to the HW store? Make sure to get a grade 5 bolt so your replacement doesn't snap again.
  15. upupandaway

    looking for obsolete parts or some way to repair these wheels (Sportlawn)

    If u have no luck, you could make your own replacement. You would need to make a mold of the original tire to pour this stuff into: Urethane They make different textures from soft to hard as a rock. Call a local plastics place and they can help you out.
  16. upupandaway

    OIL REFILL ACCESS - Tufftorq K46CR (locker)

    To avoid dropping mine next time i change, i cut a hole under my battery to reach and fill using the breather:I then run a tube from a funnel to this orafice.
  17. upupandaway

    Apparently I have tourettes syndrome

    With this, this is why with my 3hp table saw, I go by the rule 'don't take your eye off the blade, never put my hands between my eyes and the blade- move hands down and around the blade.' I like my fingers....
  18. upupandaway

    Won't start with air filter in

    so you blow air here that i circled or else where? If yes, then as i said before. The screw at the bottom of the carb bowl also acts metering fuel. Pinch the fuel line, take out the screw and with a needle and or carb cleaner clean out the small hole on the side and the 2nd hole on top. Just...
  19. upupandaway

    Won't start with air filter in

    So you blow compressor air into the carb and it starts? I think what that does is create a greater than normal vacuum in the carb venturi thus it starts. That would mean in the carb some crud is making it harder for the fuel to flow up as it should. Post a model # or a pic of the mower as...
  20. upupandaway

    Scored a nice tool box

    That's cool. At my work there were a few developers who I know that don't know how to use a screwdriver that were bidding on items just to resell them for a profit. I only bid(and won) items I would keep and use.
  21. upupandaway

    Apparently I have tourettes syndrome

    I think profanity was invented by mechanics.
  22. upupandaway

    Hydraulic Trans problem

    Well, this was fun... I was about to open it up to find what was wrong when i removed the plug from the hydraulic side to drain it and nothing came out. I know i poured ~2 quarts in... I stuck a drill bit in about 2 inches from underneath thinking there was a clog but nothing came out so i...
  23. upupandaway

    Hydraulic Trans problem

    I did notice when on the ground, in gear or not in gear(to push around). I can push it around as if it is in neutral all the time. "Release lever"?? Which part are you referring to?? Thanks.
  24. upupandaway

    Hydraulic Trans problem

    I have a Sabre(JD) but the problem is more a Tuff Torq problem. The mower has the k51a trans. It moves kinda slow so i figured to change the fluid. The fill plug is just under the battery so to avoid removing the trans each time to change the fluid, I cut a hole to reach the fill. From watching...
  25. upupandaway

    Scored a nice tool box

    It is amazing what companies throw away. I got 4 ~5' 8" tall Lista drawer cabinets for $40 each among a bunch of other things, from my work's factory closing. I missed out on this: Cart because i was out at the Silicon valley campus at the time they were auctioning it.
  26. upupandaway

    Stihl FS 36 Ignition Coil/Module

    If u have a FS36, it is also sold as fs44. Does this look right? https://www.ebay.com/itm/OEM-STIHL-FS-44-String-Trimmer-Flywheel-Ignition-Coil-Walbro/143667111587?hash=item21733a26a3:g:XgcAAOSwLbNfH059:sc:USPSPriority!75013!US!-1
  27. upupandaway

    Ariens 911077 Drive Disc Replacement

    I've been procrastinating at replacing mine also. So far I've gotten by spraying some adhesive onto the disk to get by. So far 3 months so good... *BUT* i think it is remove the horizontal orange bar then the shaft with the pulley will have enough play that you can lift it up and slide the wheel...
  28. upupandaway

    New to me HR-21 bogging a bit

    If u guys want some parts, I parts from this sitting around: PM me and ill send u pics of the parts i have.
  29. upupandaway

    tecumseh carb

    When i come across that, I wrap the mix screw with pipe thread tape. Make sure not to wrap the tip but only the threads. https://www.homedepot.com/p/1-2-in-x-520-in-Thread-Seal-Tape-31273/202206819
  30. upupandaway

    Echo SRM2100 SB Attachments

    I had a srm2301 where I tried the shc225 hedge trimmer head to fit the shaft. It is not easily interchangeable but it fit... The 2301 fit the current trimmer straight shafts(i think) so.....
  31. upupandaway

    mower salvage yards in houston

    There was an 'aspiring' salvage yard back when i was in Chi. I say aspiring because it wasn't an acre but they did have at least 50 mowers alone + other stuff. I could take a whole mower\tiller for $10(rider= $20 and they had a few old Cub Cadets!!) and dump\return what i didn't need when done...
  32. upupandaway

    Should I sell my JD JX75 for a new Honda?

    Sorry, beg to differ. I have seen numerous hondas where the trans was broken- retail brands I cannot say i ever found one but have seen missing parts or stripped teeth on wheel but not broken gearbox. From the trans that i've seen, if u get one, get the honda that has x(I think it was 5)...
  33. upupandaway

    8 Hour Review - MTD Cub Cadet RZT SX54

    No offense but a quick lookup of oil flow through a 3/8" pipe alone will handle 1.89cu ft/min. and there are how many holes in the standard filter? Being it is not a 4liter engine it won't be pumping anywhere close to the limit. Personally i use a Wix car filter on my Kawi because it is flat...
  34. upupandaway

    Troy-Bilt Lawnmower SP Issues

    "handle and the box " Oh. Oops my bad - mine had a different handle. scratch that idea. Did u already try the add washer trick i mentioned?
  35. upupandaway

    Troy-Bilt Lawnmower SP Issues

    It is kinda pain to do that with this mower cuz if u take the front apart the belt is loose so u r just eyeballing it if the belt is loose. If u want to check if the belt is tight I think the best place is to look underneath with someone or held with a rope to see if the belt is tight. By the...
  36. upupandaway

    Troy-Bilt Lawnmower SP Issues

    If your mower has the triangle box with a trigger there is a nut where the cable enters the box that u can tighten the cable. Or else post what setup your mower has.
  37. upupandaway

    Troy-Bilt Lawnmower SP Issues

    Can u post a pic or model number? Odds r it is 2 likely causes. The belt stretched so u need to pull a little further to make it grab or else maybe the belt is hard shiny that it is slipping.
  38. upupandaway

    Looks Briggs is going to file Charter 11

    My bad.I remembered the distance wrong. I found it funny being on the news while in school in UIUC.
  39. upupandaway

    Looks Briggs is going to file Charter 11

    That's my title!! I will sue you and use the court precidence how a man in central Illinois has a family restaurant named Burger King. The chain cannot open a store within 100 miles from his resteraunt. :p
  40. upupandaway

    Toro/Kohler won't run/stay running

    Keakar - of the ones I've seen, they don't have the fuel shut-off like hondas. 7383ski - did u clean out the screw from the bottom of the float bowl? I can't say what the problem was, but i went through 3x to finally getting it to purr. Clean out the small holes in the float bowl screw with...
  41. upupandaway

    Looks Briggs is going to file Charter 11

    Yeah. briggs has been making the whole product(mowers, generators, edgers, etc) the last few years after buying up several brands. They said this month they will sell off the brands and only supplying engines in the future.
  42. upupandaway

    Looks Briggs is going to file Charter 11

    This is old news. It was a few weeks ago when they mentioned that Briggs owes a few $million in interest payment this month. It doesn't take much for people who follow stock to know their cash on hand is no where close to what they owe. Paying the high ups confirmed it. Now to wait for the...
  43. upupandaway

    Needing help on a price

    Rivets' quote reflects my experience. Being Sears is like Levi's vs Gucci jeans - most everyone buys them for utilitarian reason where people buy a "green mower" at least partially for its name. There was a shop where i lived in Chi that had a row of sears riders to be scrapped. I talked to the...
  44. upupandaway

    A Good,Good company

    Yeah being Stanley owns Craftsman now, if it-from sears that is breaks(I read they would honor all sears tools), u have to pay postage to send it to them before they will send u a replacement. That cost alone defeats the purpose.
  45. upupandaway

    Old gem

    The only parts I recall I replaced on my Sears rider were the spindles-from hitting rocks in my new Tx. yard, and the brake parts. There was a vocational school in Missouri that had a small engine class and they sold parts also. That's where i got them but looking lately,i think they are out of...
  46. upupandaway

    Lawnboy lawn mower

    FYI: You press the primer to squirt some gas from the bowl below up into the air passage. When the motor is running, the vacuum of the air the engine is pulling in does this. So yes, when u press the primer you should expect to see a little gas come out. So long as u see gas come out, a torn...
  47. upupandaway

    Old gem

    look under the right rear wheel. That is where the brake is. There is a stopper on the shaft that moves fwd and back as you press the pedal. Have someone press and release to find what is stopping. Maybe the stopper is way back so there is very little travel to press the brake. On mine, the...
  48. 70's Sears tiller

    70's Sears tiller

    Bought it for $10 in 90's
  49. upupandaway

    Old gem

    Mine(86) has the same deck and a 12hp briggs also. Keep it!! It is the last years before sears started going downhill using cheap plastic parts like screwing together pieces instead of the single solid frame that doesn't flex-again like current mowers.
  50. upupandaway

    Stihl HT75 tuning problems

    You could but you shouldn't have to. I would clean it out first. I say this because the spring doesn't push very hard to keep the needle closed. -BUT- being a hacker that i am, you could try it but that means you can toss the general rule of thumb of 1.5\1.75 turns of the fuel mix screws, etc...
Top