Search results

drain oil and gas, Replace. Dry off with leaf blower. Place in sun all day. Use motorcycle cable lubricator for best cable lube. Add pressure wash if covered in mud. Lube axles and transmission if you have the time. Don't forget to remove spark plug and spin. Add some atf pr mmo into cylinder...

I don't know because I don't have one, but do the autochoke versions have any springs on them?

there are many spring configurations on the 6.75 hp 120000 series motors. Many are in the Briggs repair book showing those configurations. This is on a Toro vertical mower engine. No idea whether yours is vertical or horizontal. This one is a 125K02-0189-E1

can't say mine moves much more (and its new since I remanufactured my 20 year old Toro with a Briggs and Stratton engine a couple weeks ago) . You need to adjust it properly and see if the problem goes away. The uses that governed engine have don't usually require a variable speed so it doesn't...

The screw is only needed if a cable attaches there. That mount is on many mowers where nothing is mounted to it. It is that way on our mower for 20 years now.

Have you verified that the engine kill wire to the coil(s) is being connected when you turn it off? If you manually ground that wire does it also continue to run on? Both coils need to ground if it is a dual cylinder engine. Carbon deposits in a cylinder on a very lean and hot engine can...

Does it lose power when the blades are not engaged and the RPM is up? Make sure the belt moves freely. If it is binding the amount of power being drained can stall an engine.

where did you get the spark plug? I have seen two youtubes in the last 48 hours where the only thing that was wrong was the prior owner bought a spark plug online and guess what. It was counterfeit and ran the engine poorly. In both cases on general practice the people working on the engine put...

Liquid wrench is what I use. Are you able to heat the steel some without damaging the plastic? I wish there was a picture so those of us who rely on the Internet to advise could see what you are up against. If it looks like this generic wheel in an Internet search, I would use a bearing...

clean it a little as best you can with an exacto knife. Slide some heat shrink tubing over the piece of wire you will be adding. Cut the jacket off that wire at the end, pre-clean and tin it. Then try to pre-tin the nub that is left, and you already cleaned. Solder them together relying on the...

If the nut is loose so the arm can spin on the shaft, and you cannot spin the shaft in either direction, then something is jammed. Keep in mind that the engine ALWAYS tries to run at full throttle with the butterfly wide open. The job of the governor is to not allow that, and pull it back to a...

If it looks rich, it usually is. Sounds like you are restoring an engine instead of troubleshooting it.

One thing for sure, piston hit the head. Normally that means a broken connecting rod. Normally means it was running without oil pressure. Q for the OP, when did the oil light come on?

some say crankshaft gear. My 120000 series mower has a crankshaft, and a slide on gear that has its own key. Some may have the gear cast into the crankshaft, or perhaps a different way to mount the gear based on the list above. Need to look it over carefully.

you might look for a part number on your flywheel, and check the parts list for your briggs engine to see it is the right one. Maybe someone swapped it out and because it would not start got rid of it. Have you ever seen this mower run?

pull the carb bowl and see if it has fuel in it.

someone would need to know the model number and serial number to look up parts. You should try Ebay. There are different ones for sale using the search terms DISCHARGE or CHUTE. Example...

I just rebuilt a 120000 series motor. The cam was plastic on a steel shaft. Lots of articles from people who had the plastic lobe spin on the steel shaft, throwing off timing.

I don't know. I googled that and many pictures and videos came up. see https://www.lawnmowerforum.com/threads/carb-linkage-and-springs-for-husqvarna-yth24v48-with-b-s-vtwin.68400/post-464477 - maybe it might help

what brand spark plug and where did you buy them from? Was it a local auto parts store, or online? Have you checked compression on all cylinders?

give us the engine model and code it is going in. Amazon has a listing for the 797018 part and it is sold by the Briggs and Stratton Store. They are a retailer whom Briggs and Stratton uses to sell their parts. Says it fits most 122000 and 126000 series engines.

my 6.75 has a plastic lobe cam, and the lobes are known to spin sometimes on the main shaft. Have you checked valve clearances and timing?

my experience is that only rarely does a carb become "intermittent." A piece of debris can float around but usually that will get cleaned out if the carb is rebuilt. Electrical can be "intermittent". That would include anywhere there is a wiring connection, and switches. Tight valves can put an...

the plug that has the heli-coil or timesert - you may have been losing your plug ground with that if it was loose and soot was filling in around the threads. Aluminum expands more than steel. Not saying that is it but I would clean the threads well and put it back in - see if it changes...

the compression release lives on the cam gear. There are two cams depending on when the engine was built. One is NLA and the other $123. The other alternative is to buy a new motor for it. The cam is not all that hard to replace, pull the engine and then the sump. Put everything back together...

need cub model and serial number to access the manual for it. There may be a safety switch that is not allowing it to run. https://www.cubcadet.com/en_US/operatorsmanuals Model number is 8 characters

as others said - is it having trouble spinning, or trouble running even though it spins freely. If the valves are gapped looser than spec, the compression release will be less effective.

The coil(s) may be grounding out for safety reasons if certain conditions are not met. Please post the model and serial number.

Assuming this is a carb model and not fuel injection, because you say it starts when you prime it, it is likely a problem with fuel, or the fuel-to-air ratio. But it can also be a combination of things. The only way to fully know is do some testing, or go thru a general service on it. My...

what is it you are trying to accomplish?

what is the question?

Google found this. Maybe it will be similar

Pull the plugs out and see what the color is, or use an air to fuel meter to detect what the burn is at. Air Cooled engines typically like slightly richer mixtures to help with the cooling.

too rich, too lean, or bad fuel

that is: Metric: Intake valve: 0.10 Exhaust valve: 0.15 Inches: Intake valve: 0.004" Exhaust valve: 0.006" Published Specifications (Veröffentlichte Spezifikationen) for 21a907 0167 e1 050105za Intake: .004: to .006" Exhaust: .004" to .006" Metric/German: Intake: 0.1016 mm bis 0.1524 mm...

you can adjust either. If you turn the metering the wrong direction, it will get worse. 10 seconds should be long enough to improve the mixture. Or you can speed it up a little, tune the idle mixture, slow it down and adjust it some more. Basically walk it down. Running it dry before putting...

As stated above, that is oil cooked onto the head. If it is above the exhaust port, that is all it is. If it is on a part of the head where there is no exhaust port under it, it could be gasses leaking thru a valve guide. Below is a "burnt exhaust valve" where the gases leaking past it eroded...

I might look for a broken vacuum line going to the fuel pump before tearing the carb apart.

First thing is check to see if the choke is opening especially if it is a cable operated choke. Google says the engine you list has a manual knob to open and close the choke. I don't know but if the choke was not moved to run by the operator, what you describe would happen. Jacks Small...

unusual issue. Many of these carbs the last 20 years use a couple small punch marks to hold the butterfly in place, and no screws. Kudos for finding that.

Briggs and Stratton oil recommendation. In summer I suspect that it might get up to 110F in some places but people usually do yard work during the cooler part of the day. One thing for certain as some post - keep the engine clean of debris so it gets good air cooling.

Motor Oil Geek did a study on seven major oils used in auto engines. (hint - Amsoil was not the one that came out on top). You can find the study here:

the reason the classes aren't offered is that there is little financial incentive to learn trades like small engine repair. Then on the sales end, small shops have to compete with big box stores. This is happening at the same time the cost of living has gone ballistic in the last six years, so...

Dollars and cents. I recently remanufactured the 190cc Briggs and Stratton engine on a 2006 Toro super recycler I bought new in 2006. Also replaced worn out wheels, put in a new blade, belt and just serviced the axles since they were just rebuilt 3 years ago. Cleaned it up and made it like...

shipping. Have to figure out what else it fits and look to FB marketplace for a broken mower

Replacement bag no frame $25 on Amazon...

There is a whole market for canned fuels here in CA now. Almost impossible to find non-ethanol pump gas except at the airport for small aircraft. The irony is that the environmentalists wanted it and a couple years ago, like 2022 I think, The National Academy of Sciences did a detailed...

in answer to the question - whether it worked or not when she bought it used. If it worked the it was likely to be a learning issue. If it wasn't demonstrated as working, then it could be either a learning issue, or a mechanical issue.

post a GOOD CLEAR photo of what you are up against