Search results

Yes, I have already installed a shutoff on mine. My last mower had the gas tank behind the engine and gas would end up in the crankcase. Briggs self destruct system #1.

Thanks for the clarification. Is there a wrong way or right way to bypass the solenoid? I have one with the plunger removed, that doesn't leak. Can I just install that?

I'm a little confused. Are you recommending that I bypass the solenoid? I've done some additional troubleshooting and narrowed down the problem to be the electrical connection between the wire and the pin inside the connector attached to the solenoid. When I pull on the wire with the key on...

I already have a manual fuel shut off installed. I didn't know if that was a safe alternative. I would still like to restore the operation of the solenoid, if possible. I was hoping someone had success with an aftermarket solenoid and could pass along the source.

In troubleshooting a popping issue I discovered that the electrical connection to the fuel cutoff solenoid was lose. When I wiggle the connector (doesn't take much) I can hear the solenoid cut in and out. I had a spare one from another carburetor that fit the connector better but it has a...

I just wanted to share my experience after several replacement of the carb on a 44R677. It probably applies to other models as well. Main takeaway - NEVER assume the person that worked on your mower before you knew what they are doing. I don't know why, but I keep forgetting this. When it...

Thanks. Right now it looks ok and I will monitor the steering performance. If it becomes a problem I will take measurements and see about swapping in adjustable links. Do those adjustable rods hold up? Are there ones to avoid?

Great information. I wasn't sure about the CVT. When you refer to the NZTR steering - is that the steering gear only or is it all the connecting hardware? There was some play in the front end but it improved when I went to roller bearings.

I think Craftsman recycled the model designation. The tag show Model 917.203911. From the manual "The Craftsman T3200 is a T3000 series lawn tractor. This model was manufactured by Husqvarna built from 2014 to 2019. The components of Craftsman T3200 driveline system: Briggs and Stratton...

I have a older Craftsman T3200 that is showing its age. I have already replaced the tires and upgraded the front wheel bearings. I'm having engine issues and that is a side issue. My backyard is about .75 acre with a 10 - 12% slope. The ground is weeds and native growth. The front is level...

I agree with the direction you suggest. I will test the flow from the pump. I have blown out the line. I also plugged up the line at the tank and blew in the hose at the pump and it held pressure - there was no leakage. I'm also thinking there might be water in the gas. Before I purchased...

A solenoid with no tip.

I removed the solenoid and replaced it with a bypassed one. No difference. I also disconnected the choke to see if it would start with the choke on or off - still no difference. I'm about ready to sell it as junk and hire someone to cut my lawn.

I can feel/hear the solenoid click when I turn the key. I loosened it to see if there was gas in the bowl and there was. The one thing that isn't working is the choke. The linkage on the carb seems to be designed for a seperate cable that pulls forward (choke on) and back (choke off). The...

I have a riding mower with a Briggs 44R677 Type 0018G1. I acquired it from a sketchy used repair/dealer in my area. I put about 2 hours on it - ran fine - until I noticed it was leaking gas out of the fuel pickup under the seat. After replacing the pickup grommet, hose, and fitting it no...

That is exactly the problem. The guy didn't even look at my mower to get an estimate of it's value. Profit seems to be his only concern. My satisfaction or ability to have a working mower didn't seem to enter his mind.

Most of the oil had already leaked out.

I'm assuming the seal replacement would require that the motor be removed. Not too bad but I wasn't in the mood to go through all that again.

I took my riding mower into a local repair (and used equipment dealer) to fix a (brand new) bad oil seal. I had just fixed a governor problem, but was just tired of working on it. The repair guy made no secret that he wanted me to trade mine in on one of his repaired used mowers. I told him...

I wanted to bring everyone up to date on this issue. After searching The Tubes I found a mechanic that discovered a similar issue. It seems that when my motor over-revved (although very briefly) the centrifugal governor mechanism flew appart inside the engine. Now the only mechanism from...

Do you have a source for the Service Information? Briggs only has operator and parts list manuals on their website. The governor was adjusted to address a surge issue at operator throttle and not an idle issue.

Engine on a Husqvarna 46in riding lawn mower. After replacing the carburetor I have had issues with surging and idle. The replacement is not an exact model but very close. Initially, the engine would constantly surge when not under load. It also didn't seem to run fast enough. I reset the...