Search results

Well friends ... I bought a complete set of internal tubes, but ... I bought Maggion 20x8.00-8 - Lefort 18x8.5-8 *arrived... I bought Lefort 16X6.00-6 - it arrived correct (*) The salesman told me that it works ... is it correct? It's complicated here ...

dresdenfan123 Friend, I'm not a specialist and I don't even know your engine, but there are simple procedures that must be followed before exchanges. Swapping parts at random has little chance of resolving. Generically ... 1 - Is the battery fully charged? No - Charge it Yes - next step 2-...

As for the oil change, I sent an email to Peerless about the possibility of drilling (without opening) the same point that appears in their own manual ... they still haven't answered me and I don't even know if they will ... What do you think? My problem would be limited to just buying or...

I understood... OK, thanks

Yes, I kept it carefully ... So, by this measure, the high part of the disc faces the tip of the shaft ... in mine there is a difference of approximately 3mm, coinciding with your information. New tablet used tablet Where I live I have two problems buying parts. 1 - Find the part. (Few...

Well, I could only see the brake today ... The removal of the disc had to be somewhat aggressive due to rust, now it goes in and out manually. I don't know the thickness of the inserts, but the internal one shows a degree of wear ... does anyone know how to inform? If they are still...

It was too good to be true ... Before removing the unit I already checked that it did not have the drain point, even so I did. Small things, but important to fix soon ... Belt and pulley dragging Brake pad, tomorrow I will remove and check

Yes, I know this week-year system ... in Oregon it does, even though the tire looks more than 5 years old through the cracks ... But at Carlisle nothing similar, just this AQ19 ... and it is not possible that it is from 2019 ... 3 years and with this state of cracks !!! But what I want to...

Ride around is different from a competition ... there is a whole specific apparatus.

Well, if you're not going to follow all the engineering and safety rules for yourself and others, better go fishing.

Obviously you're not going to cut grass, but how are you going to do the suspension, the shock absorber, the brakes ... have you evaluated what the Frankstein center of gravity will look like? Aim at least on an ATV.

Yes, but mounted on the housing I think it difficult (not impossible), as there are no internal clearances to hit ... it is more likely that the glue will be released. In my case it was on the bench ... about 10-15 cm high ... it was just a scare, it serves as a warning.

No ... it fell on the table ... lucky that he released the cable and hung up. If not, it would fall on my foot

My starter burned the armature and had loose magnets. After repair, it jumped out of my hand when I tested it out of the engine ... it's very fast and strong. My engine is a B&S 31P777 18,5Hp.

Hello Houston, we have a problem ... Calm down, it wasn't like that, but I almost panicked ... After redoing the installation of the lamps, I turned on the switch ... it didn't light ... ? I thought to myself ... it must be after the engine start ... I started the engine and ... it didn't...

The model is a "Turf Saver". Based on the pictures of a new tire, my tire doesn't look too worn. Note that to reach 20 inches in diameter on a new tire, the grooves must be approximately 1 inch ... is that correct? Is this tire for snow, mud or grass? The question is, how deep is the groove...

No, my friends, my intention was never to open ... just to get to know and change the oil in case I was overdue for time. But since there is a way to inspect and replace it, I will change it, but as a precaution. Yes, I'm sure it's a Peerles MST ...

I totally agree, but he is an 11-year-old cutter, I am the third or fourth owner, he doesn't have an hour meter and I don't know under what conditions he has been kept (see my post on engine noise). As the gearbox is working well, my intention is just to change the oil and make sure it is clean...

Strange you talk about grease ... I saw this video and the lubricant is thick oil ... Looking on the net, a few minutes ago I found a Tecomseh material (the site refused to attach it, as it is very large), where I have my Peerless MST series, and in fact the lubricant is oil ... and there is...

I always try to anticipate some problems ... I am seeing information and videos about the gearbox (mine works well), it is bathed in thick oil, but has no drain or opening for changes. It seems to have a sturdy construction and a long life forecast, but not infinite ... Is there any guidance...

In fact, knowing the age now is not very important, but in a new purchase yes ... I hope that with the air chambers they will still last a long time. But what about the difference in outside diameter? Where did the 2 inches go?

OK, electronics is not a problem for me, but the wires and sockets for the lamps are missing, if automotive is easier to get LED. The circuit goes only to the Switch Interlock Clutch Cable (87), Lens grile (LH, RH) and the bezel grile (LH, RH) are there ...

Thanks for your response... For now go the common ones ... later I can even do with LED, because I have kilos of residential lamps burned of different types, but without the proper socket for the lawn mower. In the case of 25W incandescent it is between 2 and 3W in LED. Grateful

It may be a small detail or a big nonsense, but my tractor came without headlights (lamps). I know I will never mow grass at night, but to satisfy my granddaughter, I need to replace the lamps and wiring to the chassis connector. My battery is 12VDC ... I found nothing in manuals ... How many...

This post aroused my curiosity and doubts about my tires. I imagine they are already 11 years old (the cutter is from 2010), as they all have micro cracks on the sides, and at the rear there is a small leak that wilts in 3 or 4 days. Taking him to a tire shop, he found that there were no holes...

Speaking of blades ... what is the speed (of blades) recommended for a good cut? Is there any type of table for the type of grass?

Thanks for the warning, my blades are not yet installed, as I see the best way to sharpen them. The cloth that appears is just not to get dirty when lying on the floor...?

Well folks, I managed to solve the problem ... many will not like it because original pieces were not used, but it is the most viable solution for a set that has already been sacrificed, crooked and sure outside the original geometry. Steps: 1 - 3cm increase in the Link Asm Lift FXD (101) 2 -...

slomo I found the information in the Engine Repair Manual, it speaks at 1750 RPM ... it's not far from mine ... I'm going to make an adjustment starting from scratch. Bellcrank It is a good idea to observe the presence of flakes ... in my car I see it in the magnetic crankcase screw ... In my...

What are these parts for? Any other decks or implements?

Perfect, that was also my conclusion about this deck ... (I don't know others) Has anyone tried to put an arm (6) longer? This would soften the arc made when going up and down the deck. Putting in Sketchup, the best position of the arm in the part fixed on the chassis is aligned with the...

What do you say about deck is valid for everyone or is there one that is better?

Well, I did the test of auscultating the engine ... not conclusive in the sense of defining the clearance point, regardless of where I place the screwdriver. One thing that I clearly noticed is that the "tuc tuc tuc" does not increase in intensity with the increase in RPM, on the contrary, it...

:ROFLMAO::ROFLMAO::ROFLMAO:... good idea...

Okay, in fact the part 70 is slightly tilted backwards (+ -95 °) ... do I adjust it to 90 ° or less? As for piece 98, it already has the cone, a long spacer (+ - 5cm) and then the adjustment nut. From what you say, whenever I adjust the height of the deck, there is a need for a touch-up on...

My friend, my English is terrible and I use Google for translation ... nicknames or expressions have no translation. I think your numerical references are from the manual I attached ... could you confirm and explain in other words the meaning of "The solution is to put a big shifer on it and...

Murray 42L18G60X8A When I bought this lawn mower, the platform was disassembled, with dents, some tears, broken cable and with rumbling bearings. I noticed some differences between the current platform and the one in the Murray manual (basically in the part of the brake set) I recovered all the...

That's what I imagined ... here we always use a long screwdriver ... I'll do it tomorrow morning and post my impressions, but because I don't know a perfect machine, I don't know if it will help.

Let me see if I understand ... do you mean by a big screwdriver with the cable in the ear and the crack in the motor housing (like a stethoscope)? We do this procedure here to detect bearing snoring on car wheels, bearing alternators, air conditioning compressor ... is that it?

It is my friend, impossible to notice any difference ... by this procedure I would not condemn the gap between the crankshaft and the connecting rod foot (crankpin journal). But the slack can come from the two other points (mag journal or PTO journal).

I agree with the idea, but a millimeter gap that in practice results in a noise, I don't think it's noticed ... but I'll try ... The ideal would be to hold the piston by the head and pull and push (impossible ...), even so I do not know if very small clearances would be perceived. Wait for me...

Here I removed the spark plug and moved the flywheel ... turn up the sound to hear .... Before anyone asks, the tape on the grid marks the TDC. I never had contact with an similar engine in order to compare this noise... As for the screws that hold the engine, they are like rock. As for the...

Well, in practice this happens, but when recording with increased RPM, the noise of the discharge increases (mufler), suppresses the TUC TUC TUC ... and it is not very clear. In the video I forced a low RPM in order to make the TUC TUC TUC clearer ... did you notice?

I understood... In fact, I didn't see any bearings with balls, cylinders or bronzine, and if there is excessive play, both parts are exchanged. I saw a guy (video) assembling one of these and an axial clearance appeared, I will see if it is my case ... in any case, to resolve it has to open and...

Ranamow Screws that close the engine or those that secure the engine to the chassis? Scrubcadet10 Allow me to disagree ... I don't see how a subtle mismatch in valves can cause noise in the crankshaft or connecting rod ... the same happens in cars ... When I speak of subtle noise, it is because...

My engine... Where I pointed out is that the noise occurs

I'm not sure what he said, because I don't speak and hardly understand English (I use the Google translator), but it is possible that with a gap he refers to the lower or tight value ... I always prefer a central point, because it corrects previous positioning errors. I have a good knowledge of...

I have, but only in millimeters ...

Well, I found this video excellent, well prepared and referenced to the Briggs manual ... now I have no doubt. In my case, before the adjustment, it was: Input + - 0.13 mm (+ - 0.0005 inches) Output + - 0.20 mm (+ - 0.0008 inches) After adjustment: Input 0.010 mm (0.0004 inches) Output 0.015 mm...

The machine was stopped, with the starter burned ... I have already recovered and it is operational ... certainly there is a slight malfunction in the valves, but I am still not sure of the right checking / adjustment moments. There are videos showing TDC verification and another 1/4 inch...