Search results

This happened on a Craftsman T240 with the hydrostatic transmission used on many brands and now only has 198 hours on it. I am assuming other brands built by MTD have the same tractor frame. Over time transmission power drops to the point the tractor will not go up even a very small grade in...

This tractor was purchased used with only about 170 hours on the clock for a local swim club. The tractor transmission now at 198 hours begins to lose power, especially when in reverse. Eventually the transmission did not have enough power to back up into the storage building, and I needed to...

This was a lightly used scrapped tractor with 179 hours on the clock I bought for $25. The front had been hit breaking the hood. It’s been five years trying to level the blades on this deck. First yes, tire pressures are filled to spec and tractor is on level ground. The blades are not bent...

No one tells you, nor is it in the owners manual that the spindle is dry inside and needs a full new tube of grease to fill two or three of them. Only those of us on forums like this know.

This is probably not new news to many here. I hit an object that broke a deck spindle on a Craftsman T-240 46” mower. After the removing the original broken OEM spindle, the guts basically fell out of it. It had a grease fitting built into the spindle but from the factory, no grease was...

StarTech, thank you. Other than the extensive knowledge you have accumulated over the years, how did you find the part number? When I go to web sites, the only information they have is the same parts picture as I have and list no part number for the bearings.

I have been pretty successful keeping this 1998 Yard Machine in service. Model number is 13AM675G062 or just 675. It drives like a drunken sailor because the plastic bearings in the front wheels are worn out. I have the original parts manual from 1997 that shows the inner and outer bearing as...

This is on a 2006 Troybilt Pony, Briggs single cylinder engine. When mowing it intermittently developed a split-second hard misfire. It almost feels like it is a split second electrical short. Sometimes it is hard enough that the engine just about stalls, then picks up and runs. All I have...

I just had the same problem today. I jacked up the right side allowing the left rear tire to remain grounded. From the rear using a long sharp end bar (my jack handle) I put it against the rear side rim center shaft and hit the bar with a hammer, rotating the wheel and repeatedly hitting the...

Still confused. It’s leaf season and I put my home made mulch plate on the deck. I don’t want to get stuck with a broken belt mulching four yards. I ordered the shorter 91.10” belt in the wider 1/2” width and hope it fits. I think it’s easy to change so I’ll test fit it when I receive it.

Thank you for your quick reply, but I am still confused. 1. I do not know what IPL stands for. 2. Both you and I initially came up with the same part number 1732204SM. Partstree.com lists four possible belts. The one noted here is 91.10 x .34” for a shallow groove pulley. This is what I first...

Snapper LT125 Model: 2690872 Serial Number: 2014719099. The old belt shredded badly and was thrown away before ordering a new one. This unit has the electric PTO. When I go online it references two belt sizes. One for a shallow groove pully and one for a deep groove pully. How can I tell...

It has a Briggs 17.5HP I/C Type 0777E2 from 2005. New spart plug, valves adjusted, carburetor cleaned and rebuilt with a kit, new fuel filter, manual fuel shutoff valve added, new battery and the reverse mowing shutoff has been bypassed/unplugged. When mowing it runs fine, then a sharp sputter...

Just had same problem. Did the same thing, bought a solenoid that fixed nothing. Also jumped from battery to starter and got spark as you did. Battery terminals were clean BUT the positive cable attached to battery was rusted. Thoroughly cleaned cable end and bingo, it starts.

The deck has 7 positions. The lowest sets the deck on the concrete. Levels 1 thru 5 are basically too low to cut grass unless you are cutting greens or a fairway. Level 6 is boarder line too low for the average lawn. The highest level is ok. If there is excessively high grass there is no room...

Sorry for the double post. Issue found with unit #2. It was a carburetor issue. I removed the spark plug and gasoline poured out of the cylinder. The motor was hydraulic locked. The carb was removed but the internals looked clean. No crud or varnish. Used brake cleaner to clean ports and...

Unit #1 Model 31A607 Type 0741-E1 Code 070326ZE I/C 15.5HP Unit #2 Model 287707 Type 1224-E1 Code 971009ZO I/C 14.5HP I do not believe either of these units have an ignition safety interlock issue since both solenoids always activate. Both units have had their batteries swapped...

1.Model 31A607 Type 0741 E1 Code 070326ZE 15.5hp 2.Model 287707 Type 1224 E1 Code 971009ZO 14.5hp Unit #1 is a salvage mower that I swapped this 15.5hp engine into. Battery is new. Worked well until no crank, just a solenoid click. Swapped in a used solenoid and it started OK for a couple...

I see said the blind man. Like I said, I’m just a home DIY’ er.

I’m just an average DiYer but here is my two cents. If necessary charge battery just enough to start tractor then shut motor off. Use volt meter to check battery DC voltage with engine off. Then start tractor and recheck battery voltage at battery again. It should be higher now indicating...

A lot of very good advice has been given here. What causes over heating. Among other things, 1. Debris/mouse nests under engine shroud clogging cooling fins. Take the shroud off and inspect. 2. While there go a step further and inspect the flywheel key. Look close at it. If the flywheel has...

OK I lied!! It warmed up a little today, so I made it out to the garage. I released the center brake adjustment nut and the mower shifted OK. I tightened the nut some and it still shifted OK but had no brakes. Kept tightening the nut to the point where I have a very little brake pressure and...

Thank you to those that replied. Things are very hectic this time of year and I’m taking a break from the garage for now. I don’t know why but the brake was shimmed with washers on the adjustment nut and not working at all when I got it. The first thing I’m planning on doing is disengage the...

Craftsman Tractor Model - 917.252510 - 42" Deck - 16HP Briggs Transmission Dana Transaxle Model - 4360.79 This thing is about 30 years old. The engine was blown when I received it (no oil), and previous owner has no history to help. It came with the house. Just completed an engine swap with...

Thank you for letting us know your conclusion. Too many ask for help but never return to add what solved their issue. Inquiring minds need to know what solved the mystery.

I know this is a late response, but my vote goes to the plugged vent hole in the gas cap. They run about 15 minutes with a plugged hole in the gas cap then the vacuum pressure increases greater that the fuel pump can handle starving the carburetor.

Sounds like my Briggs V Twin problem. Tractor came to me not running. With new battery and wiring issues fixed it ran what I thought was ok but then, no power when PTO engaged, it died. Found mine was running on one cylinder. Getting spark. Getting fuel. Compression great. I had two...

Lt125(23420) - Too Fast!! This mower has the automated transmission with a forward and reverse pedal. No gear shift. I love it but in forward it easily goes too fast with just a light push on the pedal especially when trying to go slow mulching leaves. It is ok at first but the foot pressure...

Snapper dealer could not tell me which belt size I needed from model numbers however she sold me the 91.10” size because she said she rarely sells the other size for Snapper. It fit!!!

Timing might be off due to the flywheel key shearing. $2.13 key solved my problem. But it further cost over $250 more because previous owner drove it overheating the cylinder head which pushed out the valve guides bending the pushrods. New cylinder head, new pushrods, new gaskets needed because...

Snapper Model number is 2690875, Serial number 2014719099 42" deck. I have found reference to two belt sizes, 91.10" and 94.45". My old belt is shredded so it is no help. The different belt sizes references one for a shallow groove pully and the other for a deep groove pully. How do I tell...

Made it today. However, the jigsaw was not very effective. Rubber bounced too much. A hacksaw, drill and wire cutters worked.

I am reading a lot of these hard starting, backfire issues today and since I just solved by problem I am throwing this out there. My final solution was solved with a new $2.18 key in the flywheel. Old one was sheared putting timing off 1/8". New key, no more problem. My issue was further...

I'm new to this so I hope others don't mind me asking a question. I just do not know why a crankcase gasket would just fail on its own. Crank shaft oil seals failing yes. But, the case gasket is a non-moving, no friction part. Other parts in that area that I have found the source of leaks...

Third place to look - Remove the flywheel and check the key. Timing is off. I just repaired a Snapper that had multiple issues. Carburetor hooked up wrong, choke was hooked up backwards and fully open not closed when set. Then #1 cylinder pushrods and valve guides broken. Mouse nest...

Can you hook up a temporary fuel tank with a new hose to the carburetor and gravity feed the gas to see if it starts? This will bypass the fuel tank, hoses, filter and pump to determine if you are looking in the right area.

Oh I like this!!!!! Better than metal on metal. Thank you.

Tractor Model 2690872 Circa 2014 - I am looking for a mulch plate to fit onto my 42" deck to use for mulching leaves in the fall. I do not want to pay $160/$260 for a full mulch kit. Just looking to find only a plate to McGyver and make it fit the discharge on the deck. Any suggestions on one...

SUCCESS!! I owe everyone who replied a big thank you!! After pondering the issue for two days I pulled the flywheel. The key was sheared!! $2.18 later and it purrs. This has been a journey. I purchased this Snapper LT125 (2014) with 23.5HP from a scrapper for $25.00 last fall. It is the...

Thanks to everyone posting suggestions. I removed, disassemble and cleaned the carb including using torch tip wires in all the tiny ports. Internally, the carb showed absolutely no dirt at all. One of the cleanest one I have seem. Have not installed it yet. Giving the task a couple days off to...

Had same problem on my D105. Deck was bent where one of the spindles mounts holding the blade. Grandson must have hit something. (Make sure one blade is not bent first.). Remove the deck and turn it over. Rotate the blades by hand and see where they meet in the middle. They should match each...

Thank you for the reply. The plot thickens. It backfires intermittently when running and appears to be the cylinder with the new head. The other cylinder never appeared to have a problem. Remember I received this tractor running but I have no history. A wire going to the brake safety...

The valves were installed in the new Briggs head with the springs and keepers as an assembly when I received the head. I did not lap them. All I did was install the rocker arms and set the new push rod gaps to .005 after installing the new head. I just did a compression test and both...

Follow up - Still have issues. Cleaned and removed all carbon from the piston head and head gasket contact surface. Checked gap on both spark armatures. Installed new #1 cylinder head assembly w new valves, a new head gasket and new push rods. Cylinder walls were smooth as h*ll with no...

Thank you. I edited the original post. The valve tappets are moving free and that both cylinder heads were heavily covered in mouse nests so I know it had to of over heated. All parts of both pushrods are accounted for so I do not think I don't need to do anything other than head replacement...

Running on one cylinder with both sides getting spark and fuel. When running the cylinder opposite fuel pump makes no change when pulling spark plug but engine dies when pulling plug wire on the fuel pump side. On the dead cylinder I removed the valve rocker cover and found both push rods bent...

I'm looking for a mulch plate for a 42" Snapper deck. I found a mulch kit that includes hardware etc. Has anyone used one of these on this site? Is it easy to remove the mulch plate, leave the hardware in place and side discharge?

I'm looking for a mulch plate for a 42" Snapper deck. I found a mulch kit that includes hardware etc. Has anyone used one of these on this site? Is it easy to remove the mulch plate, leave the hardware in place and side discharge?

Snapper LT125 with Briggs 23Hp Model 44L777 V-Twin. The cylinder on the brake side valve cover is much hotter to the touch than the other side. It runs fine but does exhibit some popping when the engine is shut off unless it is throttled to an idle first. Why would one valve cover be hotter...