Search results

I DO THIS TO MOST 4 CYCLE small ENGINES BEFORE I TAKE THEM APART. (doing so gives me a heads up of how much I will need to bring them to minimum specs on the crank end play) I've even seen some of the Briggs at the upper end of the crank specs (still within Briggs specs) and they would have a...

Plastigauge is your friend in this instance, when used correctly. Now: The engine was running ok before teardown. what caused the change? (maybe rod cap distortion due to torque or ???) You need to check and keep a heads up on the end play of the crankshaft. I check crankshaft end play before...

In my statement, put the rod caps on correctly per the mark is a from the Service manual page that I posted previously. On older equipment the rod caps were actually numbered from the factory as to orientation and even the cylinder number. I always put witness marks on rod caps and stamp the...

Also mic the crank throw. If you cannot see out of round using your mic's try to confirm that both are not out of round (egg shaped) might even try confirming clearances up/down, side to side is not out of round using the plastigauge and do the same with your new rod. You indicated that you...

A member in another forum sent me a Ariens model at jacksmallengine that is a RM830E and I had to use from jacks the number 927004 at the Ariens website and got a unit parts list that is IN THE BALL PARK. The ID tag on this one has 830E, serial 095425 and has 830E PATHFINDER on a decal. This...

Is that a new rod or the old one. Have you heard of using plastigauge? (to check clearances)You can review such on-line. You will probably have to try another rod (new rod) and then use plastigauge to check the clearances since you now know it's the issue. You can test another rod without it...

I'll try Ariens in few days if nothing surfaces. The 830-E and the units serial number will get a red reject when trying to search the Gravely manual doe to not enough numbers and letter in the model number.

What is the model, code and type info on the engine?

Also since it's all gears do not overlook that it might be external to the transaxle in your shifter mechanism. Post up the Model number of your Craftsman tractor and we maybe can look at a IPL and give you another hint. Some of them shifter linkages can be hard to see unless lots of metal is...

Here is some links I've saved where you can download a free Tecumseh Peerless service manual and see if you can ID yours. Most generally the type Peerless that has the Benoite/clay grease's are not intended to be serviceable, specially built to wear out and the heavy grease is also used because...

Anyone have a link to download a Illustrated Parts List (IPL) for a 830-E Gravely Rear Engine Rider lawnmower? (this rig was made in the 80's-90's) and the Gravely site will not even accept the 830-E model number now days. I have a owners/operators manual. It does not have the IPL?

Sometime you can find a re-build kit for decks at 8TEN if you happen to need to replace spindles, blades, pulleys and belts and save several $$'s vs buying individual replacement parts. check with 8tenparts.com. You will need your mower model and serial number. If you just need bearings only you...

It's how you hold your mouth.

AirMaster flyer asked: I will check out the link on repair tips, but as I said, right now all I wanted to know was if there was a way to adjust this carb without a main jet adjustment screw, since in my close to 60 years of messing with theses small engines, I have never seen one before. You...

Here is a link to view some Tecumseh carbs with repair tips. https://outdoorpowerinfo.com/repairs/#id_tecumseh You can also download a FREE Tecumseh L-head service manual that cover several model and Hp of the L-heads. You might try these links for the free manual: I have not visited these...

PM sent

PM sent

If you have not already done so: I would do a leak down test on the engine before throwing any green backs into it for parts. The leak down can be done using a source of compressed air. If you decide on a starter DBelectric on-line has good starters and that type starter used the fiber gear...

TobyU says: People refer to the thing that the spark plug wire comes out of as all of these terms so as long as we know what they mean. or it's sometimes also termed: Check the thingamajiggy with the wire coming out going to the other thingy.

regeland: What is the latest results of your testing? John Deere LA 115 19.5 briggs and stratton starts cold runs 5 minutes and cuts off. loses spark. Has a new spark plug new gas filter, new air filter. Anyone else have this problem?

You asked: . Are any of these likely to be better than the Nikki, in the case this carb makes a habit of failing from microscopic-sized particles? No. If you can remove/install a carb and take one apart and put it back together you should take a shot at yours first. Get a can of carb spray...

That 593197 is the carb part number and it's a Nikki type. Them carbs will have the symptoms you describe. Here is some links that have some repair/re-build info about Nikki's and info about low priced re-build kits/parts. You got lucky that your twin engines does not use the dual throat Nikki...

Has symptoms of the electronic possibly failing in the magneto. (if it's not the spark plug) You can find a magneto for less than $20. If it turns out to not be the magneto, you need a spare anyway, because they are prone to failure eventually. Be careful and keep a heads up when loosening the...

What is the engine model and type?

I've seen similar happen to gas tanks that are of magnesium type. Had a old chainsaw (had been stored for several years and the fuel dried out in the tank) that had a mold type stuff growing inside. It would get past the new in tank fuel filter and clog the carb inlet screen inside the carb. I...

read post #13 and report results of the test with the kill wire disconnected.

Yes, Maybe Yes, Yes

Post up the Make, model, type of the engine on your snapper RER and maybe we can tell you how to disconnect the magneto kill wire for a spark test. Remove all the spark plug wires to look for spark and to make sure the engine does not start/run BEFORE you disconnect the magneto kill wire, This...

Are you saying that the engine cranks over fast with your new battery but the spark plug is not producing a spark when looking at the spark plug with it removed from the cylinder or ??????????????? Or it's not cranking over fast with your new battery but cranks over fast using the jumper cables...

You might consider: Charge up the lawn tractor battery, let it set 24 hours then if you do not have a battery load tester take the battery to O'reillys or a auto shop for a free battery test. If you do not have a battery charger just take it as is and probably have to leave it for few hours for...

I try to find one that wife does not have to strain or sweat to much when pushing it uphill and she prefers one that she does not have to manually wrap the crank rope around a pulley when starting the engine. She likes the auto rope recoil type of starters (after she seen one in use). Upgrading...

Ask DB electric.

I've re-built different models of the Peerless that are not recommended as serviceable. (patience is required) Post up some pic's of your transaxle or the model of the tractor it's used in. Tecumseh/Peerless has a free service manual but that one is not listed in their manual, because it's not...

If you do not have a Hz (frequency meter) just set the voltage at 125 no load then connect a 80% resistive load and see if it maintains the voltage at 110 or above. If you have a Hz meter set the no load cycles (Hertz, HZ or frequency) at about 63-65 (using the speed adjust spring connected to...

Try using a jumper cable to the starter so as to bypass all and see if it cranks. You can do this with the key off. (using your mower battery or a automotive battery) I make a good connection at the starter stud or solenoid stud FIRST for the pos and do the ground last. this reduces the chance...

Do you want owners manual or a service manual? Here is a link to quite a few manual of all kinds. You will have to register then click on the download, manual and links section and start scrolling. Quite often when going to this site a add will jump in, just click the back button and go again...

And try letting it set at idle for awhile before killing the engine. (if it don't have a ABSolenoid) or to keep the neighbors awake and active shut the engine off while it running at high RPM's and let it backfire big time. Might get a visit from the police dept about shots being fired in the...

Grasshopper: Cracking on that black box is not a good thing. Contact dbelectric for a replacement starter then adjust the valves. You can find info on how to do all on you tube.

Appears maybe you have a Walbro LMT carb which is NLA. You can see IPL at this link. https://www.jackssmallengines.com/jacks-parts-lookup/manufacturer/briggs-stratton/briggs-stratton-engine/200000-399999-series/28a700-to-28a799/28a707-0118-01/carburetor-assy Here is a link for tips on...

Gloaso Manual Reset Fuses Circuit Breaker Low Profile ATC Fuse Breakers E39 5A 10A 15A 20A 25A 30A for 12V 24V DC Car Boat RV Solar

You might consider these for use when trying to locate a overload or short. resettable ckt breakers Gloaso Manual Reset Fuses Circuit Breaker Low Profile ATC Fuse Breakers E39 5A 10A 15A 20A 25A 30A for 12V 24V DC Car Boat RV Solar

Did not realize that pic view was from the outside where the ball was removed because I seen other holes exposed. Is that the whole side or the carb at the ball area ground off of the drilled/cast channel or ?????

Maybe take a dremel tool and put a divet or grind a flat spot. Probably have to go really slow with a sharp bit so as to not grab and spin the ball. I would rig a drill stop on the press or the bit. Might not have to drill all the way through the ball??????????? Might have to lever it out...

I've got some different size and type of needle tips (some tapered rubber and some are steel tipped that I can put on the end of my air nozzle and use high pressure air. Be sure and wear eye protection because if the clogg is on the opposite side of the ball, the ball during high pressure the...

If the existing switch is not the 7 terminal type I have 3 choices for your electrical mod. Replace the 5 terminal switch with a 7 terminal so as to keep the Anti BS. solenoid (most involved) Or just cut the pintle off the solenoid. (easiest) Or replace the solenoid with a 5/16-24 fine thread...

Wow, Bubba must have used a big impact driver. Some of them plastic intakes have a steel sleeve through the bolt holes to limit the tightening and prevent breaking the plastic so no really need in trying to do the extra leverage, it's just distorting things. And them kind of people get to...

May have already mentioned this. I usually just add a paper gasket (not really paper, it's a automotive gasket material about 1/16 inch thick) over the old intake manifold o rings. Sometimes these paper gasket material come in a kit in addition to the intake o rings. I trust the thicker intake...

Some of them China engines are a Honda clone like for example the ones labeled Predator by H Freight. If you get hung try looking at the Honda Service data.

amentac wrote: I just cleared the first snow of the year and the tractor ran smoothly, no backfires or sputtering, valve adjustment must have fixed it. Thanks for the comeback.

Hammermechanic and StarTech: Have you guys seen a Nikki produce the spit back in the Briggs Inteks that makes one think that valves are not seating? I've isolated the Nikki engine spit back right down to the carb internals on more than one engine. (not the engine or external manifold leaks...