Recent content by VirginiaIron

  1. VirginiaIron

    Core Aerator

    I got a simple hitch pin pull behind Agrifab 48” 1/2” core aerator that works well with the tray filled with CMU’s behind my riding mower. Of course any core aerator is limited by the quality of your soil and moisture. Sometimes I get 1/4” long plugs other times 2” or less. These can be found...
  2. VirginiaIron

    Turning a 3 stage snowblower to a 2 stage

    Was there enough clearance to keep the secondary accelerator closest to the third stage impeller?
  3. VirginiaIron

    Turning a 3 stage snowblower to a 2 stage

    I own a 3 stage and sometimes it is fabulous. Other times the primary augers are moving too slowly to clear the caked snow and the blades do not extend into and towards the accelerators and third stage inlet to clear any dam that has formed. I thought of extending the primary auger blades to...
  4. VirginiaIron

    Loose Hydro Dipstick - Fix?

    Here is my thought on o-rings, if you can get them. They do not have to be thick; just enough resistance for a moisture tight seal.
  5. VirginiaIron

    Loose Hydro Dipstick - Fix?

    It MUST be a coincidence, since I am a real person with some history in other forums and I do not know those other posters. I came across this thread in the ‘unanswered thread’ queue open to members. While my experience with this “type” of dipstick issue is new my wisdom in mechanic repairs and...
  6. VirginiaIron

    Loose Hydro Dipstick - Fix?

    I think I would go with a no name before using tape.
  7. VirginiaIron

    New Member

    Hey You…! Welcome to the forum.
  8. VirginiaIron

    new member

    Hey You…! Welcome to the forum.
  9. VirginiaIron

    Scag Grass Collector Modification

    I would think it should be equall or not be much lower than the deck height for clearance above whatever your deck height is set.
  10. VirginiaIron

    717-0800 Variable Speed Pulley Install

    I was thinking of having my belts replaced. I was told the main non tensioned belt can be seen flopping a bit. Both belts appear serviceable but it’s been 30 years. When we searched for the belts we did not see any matched sets from the same manufacturer. Did you use a matched belt set or get...
  11. VirginiaIron

    2014 TB30R REVS HIGH EVEN IN TURTLE MODE

    Did you try bringing the rpm DOWN with your hand/fingers?
  12. VirginiaIron

    2014 TB30R REVS HIGH EVEN IN TURTLE MODE

    I’m assuming this rpm/rev jump is NOT affected by movement of the throttle cable. Did you remove the throttle cable connection; and Is there any way you have put the throttle on reversed where fast is turtle and slow is rabbit?
  13. VirginiaIron

    2014 TB30R REVS HIGH EVEN IN TURTLE MODE

    I had an engine in the early ‘90’s that ran full throttle and it was due to the failure of the internal plastic governed spool. But it ran wide open at all times, even on startup. The OP says the engine will run at idle [upon startup] for 30 seconds then all of a sudden goes full throttle...
  14. VirginiaIron

    Ariens 46 in riding mower. 960460023-03, 93605600/A20H46

    Aye Matey! Not sure how many Seadogs are on board, ifins their not all lubbers, but this might help you out if it is the correct diagram. You might need to dig deeper. I hope this helps. Thanks for serving...
  15. VirginiaIron

    2014 TB30R REVS HIGH EVEN IN TURTLE MODE

    We need more information. You say it idles for 30 seconds; Is it idling smoothly or rough? Also, does the rpm speed creep up to high rev slowly, or at 30 seconds it just shoots up immediately to max rev? Is it a steady rev at max speed or is it an elevated rev above idle? Is the rev varying...
Back
Top