Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
ILENGINE's latest activity
ILENGINE
reacted to
mwhitnell's post
in the thread
Craftsman 22hp kohler command mower loss of power when pto is on
with
Like
.
You know that was my first thought...I removed plug wires one at a time, one killed the engine, the other kept it running. Good catch.
Nov 17, 2025
ILENGINE
replied to the thread
Craftsman 22hp kohler command mower loss of power when pto is on
.
NO. The governor needs to be in place to both control engine speed based on load and to also prevent overspeed. I suspect that your...
Nov 17, 2025
ILENGINE
replied to the thread
Report Site Issues to Me Here (or PM)
.
Welcome
Nov 17, 2025
ILENGINE
reacted to
Rivets's post
in the thread
Report Site Issues to Me Here (or PM)
with
Like
.
Thank you IL.
Nov 17, 2025
ILENGINE
replied to the thread
Report Site Issues to Me Here (or PM)
.
@Ibrahim Here is your screen shot that I just took a couple minutes ago
Nov 17, 2025
ILENGINE
reacted to
Rivets's post
in the thread
Report Site Issues to Me Here (or PM)
with
Like
.
FYI. 11-15-25. At 5:40 PM I tried to get on the site, got this message. Oops we ran into a problem, can’t load this page try again...
Nov 15, 2025
ILENGINE
replied to the thread
Repeat of Compression Relief Failure Causing Choke-Sputter-Die, or Both?
.
I agree with @Scrubcadet10 about pulling the valve cover and spark plug and turning the engine over by hand to watch the valve for...
Nov 14, 2025
ILENGINE
reacted to
Tiger Small Engine's post
in the thread
Repeat of Compression Relief Failure Causing Choke-Sputter-Die, or Both?
with
Like
.
The carburetor you installed isn’t dead on correct and is probably a large part of the poor starting and running issue. New doesn’t...
Nov 14, 2025
ILENGINE
replied to the thread
Mower Engine Info Needed
.
May be the 331877-0869-G5 But need to confirm by getting the model, type, code from the valve cover.
Nov 12, 2025
ILENGINE
replied to the thread
cub cadet xt1 lt42b brigs and Stratton engine struggles turning over and struggles starting
.
If this is a single OHV briggs engine most likely either the valves are out of adjustment or the camshaft compression release is broken...
Nov 12, 2025
ILENGINE
replied to the thread
Yardman tractor no response when shifting into gear
.
Looks like there is a 13565-7 and 13565-8 which is the 1987 or 1988 model year of the 40 inch deck. Also there is a 13607-7 which is a...
Nov 12, 2025
ILENGINE
replied to the thread
Yardman tractor no response when shifting into gear
.
See if this applies. If not then we will need the actual model number starting with 13 to give better assistance
Nov 11, 2025
ILENGINE
replied to the thread
Kohler 21hp loud knocking
.
I have seen 2 with the Kohler crack and one that ventilated the rear block due to counterweight link failure. Also have a few in my...
Nov 11, 2025
ILENGINE
reacted to
Auto Doc's's post
in the thread
GX270 no start
with
Like
.
I would try a new plug. Often times a plug will show fire in the open air but not work under cylinder compression pressure.
Nov 11, 2025
ILENGINE
replied to the thread
15W50 vs 20W50 for the hydros
.
Hydrogear uses 20w50 from the factory, but also recommends using what ever the mower manufacturer recommends. I have seen mower...
Nov 10, 2025
Top