Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
ILENGINE's latest activity
ILENGINE
replied to the thread
Engine replacement
.
The rod cap bolts being loose was a symptom not the cause of the failure. Unless the engine failed within the first few hours the rod...
Jul 26, 2025
ILENGINE
replied to the thread
Kohler Courage single cylinder engines.
.
Yep, they are still trying to beat the SV singles to death because of a few engines that had mistorqued top cover bolts, without...
Jul 26, 2025
ILENGINE
replied to the thread
husqvarna gt2254 transmission belt installed pic wanted
.
Don't see that configuration anymore. From the bottom of the transmission pulley start the belt and go to the left side of the engine...
Jul 26, 2025
ILENGINE
replied to the thread
Won't Spin Past Compression Stroke
.
Yes, but the valves need to be properly set within tolerance to make the final decision if the compression release has failed. But...
Jul 24, 2025
ILENGINE
replied to the thread
Spindle Bearings
.
Red and tacky is a #2 NGLI grease. And is recommended for high speed and wheel bearings.
Jul 24, 2025
ILENGINE
replied to the thread
Snapper LT 125 Mower deck pin.
.
Here you go part number 721221 https://www.partstree.com/parts/snapper-721221/ item 17 on this diagram...
Jul 24, 2025
ILENGINE
replied to the thread
Briggs & Stratton OHV Plastic Engine No Compression
.
I wouldn't really call those gouges. More like deep scratches, and like you I have seen mowers run with far worse cylinders. I agree...
Jul 24, 2025
ILENGINE
replied to the thread
Snapper LT 125 Mower deck pin.
.
For us to look up the part number we will need the actual model number of the mower from the model/serial number tag.
Jul 24, 2025
ILENGINE
reacted to
Auto Doc's's post
in the thread
Website slow
with
Like
.
Thanks to all the folks that have stuck with this issue and finally hammered it out (I hope). So far, knock on wood, everything has...
Jul 24, 2025
ILENGINE
reacted to
Auto Doc's's post
in the thread
Mower and lights quit on my Grasshopper 727k
with
Like
.
Hello MedicineMan7, Look for a main fuse box and check all fuses, then inspect all harness wires for any rub through damage. Will it...
Jul 24, 2025
ILENGINE
replied to the thread
Briggs & Stratton OHV Plastic Engine No Compression
.
From the looks of the intake valve and cylinder walls, there is a high amount of dirt ingestion causing excessive wear The intake...
Jul 24, 2025
ILENGINE
replied to the thread
Troy Bilt B&S pressure washer throttle linkage
.
Looks like incorrect choke return spring, and the thermochoke control lever is rotated away from the choke hold open tab. So the...
Jul 23, 2025
ILENGINE
replied to the thread
Vanguard Problem -smoking
.
Doesn't appear to be any dealers in Iowa that have both Landmaster and Briggs status. I wish I was closer since I am Landmaster...
Jul 23, 2025
ILENGINE
replied to the thread
DOV
.
If it starts and runs fine after using starting fluid I would think the camshaft would be fine. But not starting without fluid makes...
Jul 23, 2025
ILENGINE
replied to the thread
Raptor SD 60
.
First thought is hole in fuel line leaking gas and/or sucking air into the line. Second thought is to check the oil to make sure it...
Jul 23, 2025
Top