Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
ILENGINE's latest activity
ILENGINE
replied to the thread
Carb Rebuild Kit Info
.
The Kawasaki part number for the complete carb is 15003-7037 JD price is pretty close to the Kawasaki list price.
Jul 12, 2025
ILENGINE
reacted to
slomo's post
in the thread
Bad boy revolt not charging
with
Like
.
Where are you getting these regulators from? Think I know where....... And having to move some pins around doesn't sound normal. Get a...
Jul 11, 2025
ILENGINE
replied to the thread
Rear Engine Mowers
.
Snapper has been licensed by Briggs to DAYE. If I remember correctly production of the RER was ended a few years back.
Jul 11, 2025
ILENGINE
posted the thread
Grasshopper 325 overheating
in
Grasshopper
.
Grasshopper 325 with the WG750 Kubota gas engine. Showing in the red when running, tried new temp sensor and that sensor reads higher...
Jul 10, 2025
ILENGINE
reacted to
MParr's post
in the thread
Kohler Engine 7000 Series fuel filter
with
Like
.
I use the Kohler filter. 10 microns and extra capacity.
Jul 10, 2025
ILENGINE
replied to the thread
445 jd
.
Rear side of the transmission toward the top center. Has a plug with 2 wires that is tucked up in the frame on the right side if facing...
Jul 10, 2025
ILENGINE
replied to the thread
Rear Engine Mowers
.
It is the Tim Taylor effect. More power.
Jul 10, 2025
ILENGINE
replied to the thread
One coil or both???
.
In some cases when 1 coil fails the other one is also going out, and in some cases with advance in part supercessions, a new coil can...
Jul 10, 2025
ILENGINE
replied to the thread
no spark issue, inteck 12.5hp won't start
.
Spark with the kill wire disconnected proves the coil is fine, and it is not failing. So the issue is someplace between where it...
Jul 10, 2025
ILENGINE
replied to the thread
Pivot Bar
.
Pivot bar is the terminalogy that SBD uses for the front axle. Like Stihl uses rope rotor for the starter rope pulley
Jul 10, 2025
ILENGINE
replied to the thread
Rear Engine Mowers
.
Don't focus so much on horsepower because unless you are mowing foot tall grass it will never be an issue. Rear engine riders have more...
Jul 9, 2025
ILENGINE
replied to the thread
no spark issue, inteck 12.5hp won't start
.
With that wire disconnected you cannot shutoff the engine, without grounding that terminal or choking the engine. On some engines the...
Jul 8, 2025
ILENGINE
reacted to
Rivets's post
in the thread
no spark issue, inteck 12.5hp won't start
with
Like
.
Today’s coils cannot be tested without an expensive piece of equipment. If you are getting no spart through your inline tester, remove...
Jul 8, 2025
ILENGINE
replied to the thread
Engine shakes while engaging blades
.
Seems like the deck belt is shaking really bad. Check the V pulleys for something stuck in the groove, or check the deck belt for an...
Jul 8, 2025
ILENGINE
replied to the thread
have snapperpro with a 406577-0139-E1 installed governor problem
.
Could be that gasket but don't overlook the float valve 698537 and be careful and don't drop the jet out of the white plastic...
Jul 8, 2025
Top