Export thread

snapper starting problem...

#1

S

suepic

Hello, i have a snapper frp216016 with starting issues. I cleaned the carburetor and it will start right up with starter fluid and will go all day but if i try to prime it then pull start it it won't start. took the primer all apart and put two gaskets behind the air cleaner, seems to prime nicely now but still won't start with the pull start. Any ideas where i should look next? Would it still be a carb problem? thanks for any advice.....


#2

M

mechanic mark

https://www.lawnmowerpros.com/pdfs/snapper/7006059.pdf

check air filter for replacement & adjust valves with engine cold, post engine make & all numbers from engine


#3

Boudreaux In Eunice La.

Boudreaux In Eunice La.

suepic said:
Hello, i have a snapper frp216016 with starting issues. I cleaned the carburetor and it will start right up with starter fluid and will go all day but if i try to prime it then pull start it it won't start. took the primer all apart and put two gaskets behind the air cleaner, seems to prime nicely now but still won't start with the pull start. Any ideas where i should look next? Would it still be a carb problem? thanks for any advice.....
Click to expand...

What year is that engine ???? I assume its the Briggs engine you have on there by the way you describe it..... Doesn't have to be exact on the date......

Let us know Mon Ami ~!~!


#4

S

suepic

Hi everyone and thanks in advance...... hopefully i have done this right, i have sent 4 photos.....

Attachments











#5

Boudreaux In Eunice La.

Boudreaux In Eunice La.

suepic said:
Hi everyone and thanks in advance...... hopefully i have done this right, i have sent 4 photos.....
Click to expand...

Well either something wasn't clean all the way or that O ring on that intake is really worn...... Or the intake tube is loose where it bolts to the block......

The intake is in the center of that plate in pic 2 ....... The O ring is on the tube ............. Does it sputter a lil bit while running ?????

Let us know Mon Amie ~!~!


#6

S

suepic

Thanks Boudreaux, with your suggestion I will go through the carb one more time and then also check the things that you suggest, but I will have to wait till after this snowstorm stops! Lol
Much appreciated!


#7

Boudreaux In Eunice La.

Boudreaux In Eunice La.

BTW check the 2 bolts that hold the carb plate to the block ..... Those get loose also.......


#8

M

mechanic mark

mechanic mark said:
https://www.lawnmowerpros.com/pdfs/snapper/7006059.pdf

check air filter for replacement & adjust valves with engine cold, post engine make & all numbers from engine
Click to expand...


https://www.searspartsdirect.com/partsdirect/user-manuals/frp216016-snapper-parts-manual

click on manual see page 18 troubleshooting


#9

S

suepic

Boudreaux In Eunice La. said:
Well either something wasn't clean all the way or that O ring on that intake is really worn...... Or the intake tube is loose where it bolts to the block......

The intake is in the center of that plate in pic 2 ....... The O ring is on the tube ............. Does it sputter a lil bit while running ?????

Let us know Mon Amie ~!~!
Click to expand...
hi boudreaux, took the carb off and recleaned and also replaced small gasket under needle. Also i replaced o ring around intake valve, everything looks good, will still start right up with starter fluid but won't start with the primer bulb which works very well and a pull ......(also doesn't sputter at all). any suggestions what i should look at next? any help much appreciated.......


#10

Boudreaux In Eunice La.

Boudreaux In Eunice La.

Here's a video I made some time back.............. In the video I said GAS goes thru there NO I MEAN'T AIR..... Air goes in there and forces the gas.....

Seems like you have a issue with your box or primer not working just right.... Hope this helps .....

https://youtu.be/iuIWIC6NjF8


#11

S

suepic

Boudreaux In Eunice La. said:
Here's a video I made some time back.............. In the video I said GAS goes thru there NO I MEAN'T AIR..... Air goes in there and forces the gas.....

Seems like you have a issue with your box or primer not working just right.... Hope this helps .....

https://youtu.be/iuIWIC6NjF8
Click to expand...
thanks, wish i had seen that video sooner......primer works great now but still won't start with a pull.....bummer ready to give up


Footer Links 1

Top