Hi,
I have an older M281019BE Snapper RER.
Trying to get it running again after buying it for cheap.
Figure to go through it and fix what was needed.
Had to replace some shot wiring and stayed with the old Harness and went by the Wiring Schematic, but...
Having problems with 2 of the...
I have a problem with a Husqvarna Z248F zero-turn mower. It's a 2015 model. When I move the steering levers inward with the seat occupied, the motor stops. It seems logical that the problem is probably with the safety switch under the seat. I've removed the seat switch and by using a...
Working on a 42" Hustler model 927368/ SN 05011533
Helping a friend with his issue: When he turns blade clutch on the engine dies.......mower was operational until this problem developed. I would appreciate help with where to begin the problem search. Fuses are good.
Thanks in advance,
bartles
Craftsman rider. New ignition switch, battery, wiring harness and spark plugs. Turn the switch to on position and volt dial does not move. What should I look for next?
Kentucky Fried Chicken might be switching to Texas Fried Chicken and still call it Kentucky Fried Chicken. I wonder if that going to be Fried Armadillo instead of fried chicken since they moving their HQ to Texas? That way you get four drumsticks and no wings. There are plenty of armadillos to...
I can get my Husqvarna RZ5426 started. When i try to release the e-brake or move the steering arms my mower shuts off. Any help would be greatly appreciated. The steering arms are in the neutral position and when i release e-brake it wants to shut off.
So I own a Huskee LT4200 with a Kohler courage SV530-0222. I went out after winter to start it up and the solenoid just spun and did not rise to engage. So I replaced the solenoid, same symptom. Then I heard chattering coming from under the seat, so I think relay, replace that. Same issue, then...
I recently purchased a 26hp, 60 inch, zero turn Bad Boy from Tractor Supply. Today, I stood up while it was running to see if the seat kill switch worked. The engine died, as it's supposed to, but now it won't start. The brake is engaged. That's not the problem. Does anyone know what's going on?
I have a Z248F. After I start it up and move the levers in from the Park position the left arm being moved in causes it to shut off. I know that moving them both in simultaneously is what you have to do but I did notice that it’s the left arm by moving it in and out it reengages when moved out.
I bought this mower new back in 2016 and due to my not thoroughly checking it out, the seat safety switch has NEVER worked and was out of warranty before I realized it. So, a year or so ago, I replaced the switch but that changed nothing. The only time that switch functions is when I take it...
Motor turns over when key is in the run position. It started when the electric clutch went out. I replaced the electric clutch. I mowed some with it then the clutch stopped working. when I tried to start it, it cranked in the run position. I replaced the switch and switch relay. Didn't help. I...
John Deeree X590 SN:161099 (not sure of the year model......2023+-?)
I would like to replace the blank switch cover (the one intended to serve for the optional mulch system, I think), on the dash, with a Carling Techno, Contura X switch, V6D1S001.
This switch has 3 terminals: 1 power in...
The ignition is stuck in the off position. It's been kind of flaky for a few years. But always worked, until now. I looked online for a replacement part, they don't make it any more and everyone, except eBay is out. Used are selling for $75 and up. Anyway, what I'm wondering is if anyone knows...
I collect Ariens and Brott .. On my Ariens GT20 there is an old Ignition switch with the lugs numbered from 1 to 4 ..it is not a new box type ..
I would like to know what the numbers connect to as there is no wiring diagram for this ..
I have asked Ariens .. but it seems that my tractor is...
BR800 blower, runs perfectly but can not shut off with kill switch. I used ohm meter to verify both the yellow and black wires in the handle have continuity. I also cleaned the contact point on the kill wire inside the handle. I suspected bad ground b/c before cleaning the contact point there...
About five minutes into mowing with my replacement mower the other day and it appears the PTO or PTO switch went bad as the blades disengaged and wont re-engage when I pull the switch.
I have never worked with an electric PTO before. Does anyone know if the switch can be removed from the dash...
I know this topic was discussed on here before but maybe someone else might see it and know the answer. After removing the mower deck to replace blade and replacing on mower the mower will not start. I have traced the safety circuit to the PTO switch but cannot find where the brake switch is to...
Hi,
I just picked up a Craftsman riding mower; 11hp, 36” deck, 917.254270. When I went to get the old battery out I noticed there is no seat safety switch. There’s no bracket and there’s no wiring anywhere near the seat.
I don’t have a manual or wiring diagram for it so I’m not sure if it’s...
I was given a Black and Decker Cordless CMM 1200 24v mower. In spite of the the acid battery weight I love it. To be free of the cord is worth a lot. I was having trouble with the safety key/switch. It wouldn’t make contact. I cleaned up the switch and it worked fine until yesterday when smoke...
I hope someone can help me, I’m struggling to re-connect the wires to my ignition switch on my Honda 1211 ! The three wires I have are White, Brown and Orange, could anyone tell me which wire connects to which terminal G L S M and B please ?
Many thanks in anticipation
Craftsman 917.289272 (YT4000 ??) MFG in 2010. Upgraded front wheel bushings using bearing kit upgrade and added washer bearing also. But now steering control over front wheels has a problem where both front tires direction will suddenly turn just a bit left or right requiring constant steering...
Hi,
I have an older M281019BE Snapper RER.
Trying to get it running again after buying it for cheap.
Figure to go through it and fix what was needed.
Had to replace some shot wiring and stayed with the old Harness and went by the Wiring Schematic, but...
Having problems with 2 of the...