scag

Hi all, I need to replace a worn out idler arm for my 52" Scag walk behind SWZ-14KA built in 1990. The hub portion has been damaged by letting the bronze bushing wear out very badly. Problem is: The part needed is the 46145 but it is no longer available at Scag and they do not provide any...

Hello. 5 acres of former cow pasture in South Central Texas. Mostly native grasses, but will seed turf at some point. Soil has a good bit of clay and is pitted from hooves, so it is not smooth. Most flat, but a couple ditches/swales. Looking at the Patriot and lower levels based on budget...

I overhauled my hydro pumps after a slow leak for a couple seasons now. After replacing the seals and reinstallation, I followed the procedure to purge the system while the transaxle is released, then reengaged, but still have frothy oil. I can’t find any leaks from the pumps anywhere and the...

It is Part # 483422, approx 1/18" side play, normal or not ? Only the one pulley.. May be beginning of very slight noise down there. Only has 58 hours on it.

I have a Scag Turf Tiger with a 26 Kohler EFI engine. The engine is relatively new however, I have changed the stator regulator and key switch. The battery isn’t charging. All fuses check out ok and the gauge on the console shows on the low side not charging while running. The battery shows...

Scag diesel alternator good not charging

Hi! My Scag 36" walk behind has a problem i can't figure out. When i try to put the blades in gear or put the trans in gear the motor sta;;s. Can't figure it out Any help is very much appreciated Thank You

Have a Scag SW36-14KA with a Kawasaki one cylinder OHV engine on it. There is no label on the engine for information. In the parts breakdown of the mower this unit should have a flathead engine. Was there a serial number or year that the mower came with an OHV engine?

I have a scag turf tiger with the kohler aegis motor. Starts up fine but after 5 mins starts coughing here and there then eventually dies. it cranks but doesn’t start up. I leave it alone for while, then when I try again starts right back up like nothing wrong. Eventually does it again after...

My scag 36" walk behind comercial mower stalls when i try to turn blades on or put it in gear. Any idea why

First post, new member from Indiana. Let me tell you first I got over 3 acre yard. All flat ground. Got a cub cadet regular lawn mower now but it takes us over three hours to do the whole yard. Couple friends told me about this outdoor equipment place that is about 30 minutes from the house...

My father is 81 years old and having some memory/cognitive issues but has unfortunately continued to use his ~20 year old Scag mower. My mother told me that three times he has added oil to the oil filler on the left side (the hydraulic oil reservoir) and she keeps finding a puddle of oil under...

I'm really excited to have taken home a 21" Scag this past week. It will be replacing my 2022 Honda HRX217HYA. This mower is actually is a bit of a unicorn. According to the deck model, it's technically a 5v. However, it appears that someone at the factory put the wrong CV224 engine on it...

Has anyone had a problem keeping their Turf Tiger in a straight line? It does not slowly drift one way or the other but moves erratically away from your intended line. Steering shocks have been replaced with new HD units. Would front wheel preload have any bearing on this? Any thoughts would be...

Hi! two things . How do you tell the model number if there is no plate or sticker on it with the info and my problem is when i try to switch the blades o nor put it in gear the motor stalls. Ran great then one day got the problem. Thanks hope someone can help

Looking for parts for a Scag Wildcat 61. Kawasaki 26 hp . Cover. Part # 140912106 Case Part # 320996006 Bolt.flanged. part # 130BA0660. Qty 2 All three are back ordered at Kawasaki with no ship date suggested.

I mow about 5 acers and do it now with a BX2380. It has 2 steeper slopes and sort of worried if I can use a Turf Tiger on it. I measured the slope on the steepest one and it varied between 16 and 21 degrees. I really want to go with a zero turn to finish faster but don't want to waste my money...